2003 YAMAHA BREEZE light

7-61
CROSSING A SLOPE
Traversing a sloping surface on your ATV
requires you to properly position your weight to
maintain proper balance. Be sure that you have
learned the basic riding skills on flat ground
before attempting to cross a sloping surface.
Avoid slopes with slippery surfaces or rough ter-
rain that may upset your balance.
As you travel across a slope, lean your body in
the uphill direction. It may be necessary to cor-
rect the steering when riding on loose surfaces
by pointing the front wheels slightly uphill. When
riding on slopes be sure not to make sharp turns
either up or down hill.
5VJ-9-60-07 3/26/02 9:15 PM Page 62

8-39
V-belt case air filter element
1. Remove the front cover by removing the
screws and bolts.
2. Remove the air filter element cover.
3. Pull out the air filter element.
4. Tap the air filter element lightly to remove
most of the dust and dirt. Blow out the
remaining dirt with compressed air. If the air
filter element is damaged, replace it.
5. Assemble by reversing the removal proce-
dure. Be sure the air filter element is seated
properly against the case.
2
21
3 3
w
q
e
1. Front cover 2. Screw (
× 2) 3. Bolt (× 2)
1. Cache avant 2. Vis (×2) 3. Boulon (×2)1. Tapa frontal 2. Tornillo (× 2) 3. Tapón (× 2)
1. Element cover 2. Screw 3. Element1. Cache de l’élément 2. Vis 3. Elément1. Tapa del elemento 2. Tornillo 3. Elemento
5VJ-9-60-08 3/26/02 9:17 PM Page 8-40

8-83
EBU01179Replacing the headlight bulb
If the headlight bulb burns out, replace the bulb
as follows.
1. Remove the screws holding the headlight
unit to the headlight body.
2. Remove the headlight bulb holder cover,
turn the bulb holder counterclockwise and
remove the defective bulb.wThe headlight bulb is hot when it is on and
immediately after it is turned off. Wait for the
bulb to cool before touching or removing it.
You can be burned, or a fire could start if the
bulb touches something flammable.3. Put a new headlight bulb into position and
secure it in place with the bulb holder.
1
1
1. Screw (× 2)1. Vis (× 2)1. Tornillo (×2)
1. Headlight bulb holder1. Fixation d’ampoule de phare1. Portabombillas del faro
5VJ-9-60-08 3/26/02 9:17 PM Page 8-84

8-85
4. Install the headlight bulb holder cover.cCMake sure the bulb holder cover is securely
fitted over the bulb holder and seated
against the reflector.5. Install the headlight unit assembly by
installing the screws.
6. Adjust the headlight beam if necessary.
5VJ-9-60-08 3/26/02 9:17 PM Page 8-86

1. Bulb holder1. Fixation d’ampoule1. Portabombillas
1. Bulb 2.Bulb holder1. ampoule 2.Fixation d’ampoule1. Bombilla 2.Portabombillas
8-87
EBU00861Tail/brake light bulb replacement
1. Remove the bulb holder (together with the
bulb) by turning it counterclockwise.
2. Remove the defective bulb from the bulb
holder by pushing it inward and turning it
counterclockwise.
3. Install a new bulb in the bulb holder by push-
ing it inward and turning it clockwise.
4. Install the bulb holder (together with the bulb).
q
q
w
5VJ-9-60-08 3/26/02 9:17 PM Page 8-88

8-89
EBU00410Headlight beam adjustmentcCIt is advisable to have a Yamaha dealer make
this adjustment.Vertical adjustment:
To raise the beam, loosen the adjusting screw
and pull the headlight assembly toward you.
To lower the beam, push it away from you. After
adjusting, be sure to tighten the screw.
q
1. Adjusting screw1. Vis de réglage1. Tornillo de ajuste
5VJ-9-60-08 3/26/02 9:17 PM Page 8-90

8-93
wDo not smoke when checking the fuel sys-
tem. Fuel can ignite or explode, causing
severe injury or property damage. Make sure
there are no open flames or sparks in the
area, including pilot lights from water
heaters or furnaces.
5VJ-9-60-08 3/26/02 9:17 PM Page 8-94

9-9
3. Clean the drive chain thoroughly and lubri-
cate it. (See page 8-59.)
4. Lubricate all control cables.
5. Block up the frame to raise all wheels off the
ground.
6. Tie a plastic bag over the exhaust pipe out-
let to prevent moisture from entering.
7. If storing in a humid or salt-air atmosphere,
coat all exposed metal surfaces with a light
film of oil. Do not apply oil to any rubber
parts or the seat cover.
8. Remove the battery and charge it. Store it in
a dry place and recharge it once a month.
Do not store the battery in an excessively
warm or cold place (less than 0°C or more
than 30°C).NOTE:
Make any necessary repairs before storing the
machine.
5VJ-9-60-09~11 3/26/02 9:18 PM Page 10