2003 YAMAHA BEAR TRACKER 250 recommended oil

5-13
EBU01180
Engine oil
Make sure the engine oil is at the specified level.
Fill with oil as necessary. (See pages 8-13–8-19
for details.)
Recommended oil:
Recommended engine oil classification:
API Service SE, SF, SG type or higher
-20˚ -10˚ 0˚
10˚20˚ 30˚40˚50˚C
10W/30
15W/4020W/4020W/50
10W/40
5W/30
U4XE64.book Page 13 Thursday, May 30, 2002 1:49 PM

5-17
EBU00493
Final gear oil
Make sure the final gear oil is at the specified level.
Add oil as necessary. (See pages 8-21–8-25 for
details.)
If desired, an SAE 80W90 hypoid gear oil may be
used for all conditions.NOTE:GL-4 is a quality and additive rating, GL-5 or GL-6
rated hypoid gear oils may also be used.
EBU01083
Throttle lever
Check to see that the throttle lever operates cor-
rectly. It must open smoothly and spring back to
the idle position when released. Have a Yamaha
dealer repair as necessary for proper operation.Recommended oil:
SAE 80 API GL-4 Hypoid gear oil
U4XE64.book Page 17 Thursday, May 30, 2002 1:49 PM

8-8 * It is recommended that these items be serviced by a Yamaha dealer.
** Lithium soap base grease.
NOTE:Recommended brake fluid: DOT 4
Brake fluid replacement:
1. When disassembling the master cylinder or caliper, replace the brake fluid. Normally check the brake
fluid level and add fluid as required.
2. On the inner parts of the master cylinder and caliper, replace the oil seals every two years.
3. Replace the brake hoses every four years, or if cracked or damaged.Wheels*•Check balance/damage/runout.
•Repair if necessary.Wheel bearings*•Check bearing assemblies for looseness/damage.
•Replace if damaged.Front and rear
suspension*•Check operation.
•Correct if necessary.Steering system*•Check operation.
•Correct if damaged.
•Check toe-in.
•Adjust if necessary.Steering shaft*
•Lubricate every 6 months**.Fittings and Fasteners*•Check all chassis fittings and fasteners.
•Correct if necessary.Battery*•Check specific gravity.
•Check that the breather hose is working properly.
•Correct if necessary.
ITEM ROUTINEINITIAL EVERY
1
month3
months6
months6
months1
year
U4XE64.book Page 8 Thursday, May 30, 2002 1:49 PM

8-19
CAUTION:_ Be sure no foreign material enters the crank-
case. _12. Warm up the engine for several minutes at
idle speed. Check for oil leakage while warm-
ing up.CAUTION:_ If oil leakage is found, stop the engine immedi-
ately and check for the cause. _
Recommended engine oil:
See page 10-2.
Oil quantity:
Periodic oil change:
1.5 L
With oil filter element cleaning:
1.6 L
Total amount:
1.8 L
U4XE64.book Page 19 Thursday, May 30, 2002 1:49 PM

8-23 1. Drain bolt
1. Boulon de vidange
1. Tapón de vaciado
4. Remove the oil filler bolt and the drain bolt to
drain the oil.
5. Install the drain bolt and tighten it to the spec-
ified torque.
6. Fill the final gear case with oil.CAUTION:
Be sure no foreign material enters the final
gear case. Tightening torque:
Drain bolt (final gear case):
23 Nm (2.3 m·kgf)
Recommended oil:
See page 10-2.
Oil quantity:
Periodic oil change:
0.25 L
Total amount:
0.27 L
U4XE64.book Page 23 Thursday, May 30, 2002 1:49 PM

8-45 1. Minimum level mark
1. Repère de niveau minimum
1. Marca de nivel mínimo
EBU00755
Brake fluid level inspection
Insufficient brake fluid may let air enter the brake
system, possibly causing the brakes to become in-
effective.
Before riding, check that the brake fluid is above
the lower level and replenish when necessary.
Observe these precautions:
1. When checking the fluid level, make sure the
top of the master cylinder is level by turning
the handlebars.
2. Use only the designated quality brake fluid.
Otherwise, the rubber seals may deteriorate,
causing leakage and poor brake perfor-
mance.
3. Refill with the same type of brake fluid. Mixing
fluids may result in a harmful chemical reac-
tion and lead to poor brake performance.
4. Be careful that water does not enter the mas-
ter cylinder when refilling. Water will signifi-
cantly lower the boiling point of the fluid and
may result in vapor lock. Recommended brake fluid: DOT 4
U4XE64.book Page 45 Thursday, May 30, 2002 1:49 PM

8-61
EBU00570
Cable inspection and lubrication
WARNING
Inspect cables frequently and replace if dam-
aged. Corrosion can result when the outer cov-
ering of control cables becomes damaged.
Cables can also become frayed or kinked. Op-
eration of controls could be restricted, which
could cause an accident or injury. Lubricate the inner cables and the cable ends. If
the cables do not operate smoothly, ask a Yamaha
dealer to replace them.
Recommended lubricant:
Engine oil
U4XE64.book Page 61 Thursday, May 30, 2002 1:49 PM