2003 SUBARU OUTBACK service

11
Maintenance and service11-55
–
CONTINUED –
Replacing bulbs
HB5019EB
Wattage Bulb No.
1 Headlight
GT and OUTBACK modelsLow beam 12V –55W H1
High beam 12V –60W 9005 (HB3)
Except GT and OUTBACK models 12V –65/55W 9007 (HB5)
2 Front turn signal 12V –27W 1156NA (Amber)
3 Spot light 12V –8W —
4 Dome light 12V –8W —
5 Door step light 12V –3.4W —
6 Front turn signal light/
parking and front side marker light 12V –27/8W 1157NA (Amber)
7 Front fog light
Except OUTBACK 12V –55W H3
OUTBACK 12V– 51W 9006 (HB4)

11
Maintenance and service11-57
–
CONTINUED –

Headlight
CAUTION
Halogen headlight bulbs become very hot while in use. If you touch the bulb surface with bare hands or greasy gloves, fingerprints or grease on the bulb surface develop into hot spots, caus-ing the bulb to break. If there are finger prints or grease on thebulb surface, wipe them away with a soft cloth moistened with al-cohol.
NOTE If headlight aiming is required, consult your SUBARU dealer for proper adjustment of the headlight aim. For GT and OUTBACK models
HBB040BB
HBB039BA
Remove the headlight bulb cover, by turning it counterclockwise.

11
Maintenance and service11-59
–
CONTINUED –
5. To install the bulb to the headlight assembly, turn it clockwise until it clicks.
6. Install the headlight bulb cover.
Except GT and OUTBACK models
HBB046BAHBB045BB
1. Disconnect the electrical connector while pressing the lock release tab.
2. Remove the bulb holder from the headlight assembly by turning it
counterclockwise.
3. Remove the bulb from the headlight assembly.
4. Install the new bulb.
5. Install the bulb holder in the headlight assembly by turning it clock-wise until it locks.
6. Remove the electrical connector.
Front fog light (if equipped)
It may be difficult to replace the bulbs. Have your SUBARU dealer
replace the bulbs if necessary. Front turn signal light, parking light and side marker light
The headlight assembly must be removed before the front turn signal
light and parking light bulbs can be replaced. When the headlight as-
sembly has been removed and then reinstalled, it may become neces-
sary to make a headlight aiming adjustment. After a bulb has been re-
placed, it is recommended that the headlight aiming adjustment be

11
Maintenance and service11-61
–
CONTINUED –

Rear combination lights Sedan
HBB034BCHBF014DA
HBB035BB
1. Open the trunk lid.
2. Open the rear combination light cover. For covers on the trunk lid:
Unlatch the cover by pushing the knob and open the cover.For covers on the trunk wall:
Unlatch the cover by moving the knob upward and open the cover.
3. Remove the bulb socket from the light assembly by turning it coun-
terclockwise.
4. Remove the bulb from the socket.Rear turn signal light: Remove the bulb from the socket by pushing
it and turning it counterclockwise.Others: Pull the bulb out of the socket.

11-625. Install a new bulb in the socket.
6. Set the bulb socket into the rear combination light assembly and
turn it clockwise until it locks.
7. Close the cover and latch the clock.
Station wagon
n Brake/tail and rear turn signal light bulbs
It may be difficult to replace the bulbs. It is recommended that you
have the bulbs replaced by your SUBARU dealer.
HBB022BB
HBB021BB
1. Remove the light bulb replacement service hole covers at two
places by prying the edge of the cover with a regular screwdriver.
2. Remove the upper and lower nuts. Then, slide the rear combina-
tion lamp assembly to the rear and remove it from the vehicle.
HBB070BB

11
Maintenance and service11-63
–
CONTINUED –
3. Using a Phillips screwdriver, remove the upper and lower screws
that secure the side cover of the rear combination light assembly.
4. Remove the bulb socket from the rear combination light assembly
by turning it counterclockwise.
HBB025BB
HBB048BB
5. Remove the bulb from the socket.
Turn signal light: Pull the bulb out of the socket.
Brake/tail light: Remove the bulb from the socket by pushing it and
turning it counterclockwise.
6. Install a new bulb in the socket.
7. Set the bulb holder into the rear combination light assembly and
turn it clockwise until it locks.
8. Using a Phillips screwdriver, install the side cover to the rear com-
bination light assembly.
9. Fit the rear combination light assembly into the vehicle body and
tighten the nuts from the interior of the vehicle.
10. Reinstall the light bulb replacement service hole covers.

11
Maintenance and service11-65
–
CONTINUED –
2. Remove the cover and lens.
3. Pull the bulb out of the socket. Install a new bulb.
4. Reinstall the lens and cover.
5. Tighten the mounting screws.
Map light, dome light, luggage compartment light and door step light
HBB068BD
HBB029BD
HBB067BB
HSA005BB

11
Maintenance and service11-67
–
CONTINUED –

High mount stop light Sedan
OM-H2350
1. Remove the high mount stop light cover by prying on the edge
with a screwdriver.
2. Pull the bulb out of the socket. Install a new bulb.
3. Reinstall the cover. Station wagon
HBB028BA
1. Remove the mounting screw covers by prying on the edge with a
screwdriver.
2. Remove the mounting screws using a phillips screwdriver and then
remove the high mount stop light cover.
3. Pull the bulb out of the socket. Install a new bulb.