2003 SUBARU IMPREZA change

Instruments and controls
3-15
– CONTINUED –
Always make sure this light is out before you start to drive. Front-wheel drive warning light
(for AT vehicles – if equipped)
This light comes on when All Wheel Drive is disen-
gaged and the drive mechanism is switched to FrontWheel Drive for maintenance or similar purposes. Shift position indicator (AT vehicles)
This indicator shows the position of the shift lever. Turn signal indicator lights
These lights show the operation of the turn signal or
lane change signal.
If the indicator lights do not blink or blink rapidly, the
turn signal bulb may be burned out. Replace thebulb as soon as possible. Refer to the “Replacing
bulbs” section in chapter 11.
High beam indicator light
This light shows that the headlights are in the highbeam mode.This indicator light also comes on when the head-
light flasher is operated. Clock
1) “S”
button
2) “H” button 3) “M”
button
To set the hour, press the “H” button. To set the min-
utes, press the “M” button. To reset the minutes the
“00” with a radio time signal, push the “S” button.
CAUTION
To ensure safety, do not attempt to set the
time while driving, as an accident from inade-quate attention to the road could result.

Instruments and controls
3-17
– CONTINUED –
High/low beam change (dimmer)
To change from low beam to high beam, push the
turn signal lever forward. When the headlights areon high beam, the high beam indicator light “a ”
on the instrument panel is also on.
To switch back to low beam, pull the lever back tothe detent position.
Headlight flasherTo flash the headlights, pull the lever toward you and
then release it. The high beam will stay on for as
long as you hold the lever. The headlight flasher
works even though the lighting switch is in the “OFF”
position.
When the headlights are on high beam, the high beam indicator light “a ” on the instrument panel
also comes on.

Instruments and controls
3-18
CAUTION
Do not hold the lever in the flashing position for more than just a few seconds.
Daytime running light system
The low beam headlights will automatically come on
at reduced brightness when the engine has started,
under the following conditions: The parking brake is fully released.
The light switch is in the “OFF” or “p ” position.
The automatic transmission selector lever is set at
other than the “P” position.
WARNING
The tail lights, parking lights, and side marker
lights are not turned on by the daytime run-ning light system. The light switch must al-ways be turned to the “a ” position when it
is dark outside. Turn signal lever
1) Right turn
2) Left turn
3) Lane change for right
4) Lane change for left
To activate the right turn signal, push the turn signal
lever up. To activate the left turn signal, push the
turn signal lever down. When the turn is finished, the
lever will return automatically. If the lever does not
return after cornering, return the lever to the neutralposition by hand.
To signal a lane change, push the turn signal lever

Instruments and controls
3-19
– CONTINUED –
up or down slightly and hold it during the lane
change. The turn signal indicator lights will flash in
the direction of the turn or lane change. The lever
will return automatically to the neutral position when
you release it. Illumination brightness control
When the lighting switch is in the
“p ” or “a ”
position, you can adjust brightness of the instrument
panel illumination for better visibility.
To brighten, turn the control dial counterclockwise.
To darken, turn the control dial clockwise.

5
5-1
– CONTINUED –
Antenna system 5-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FM reception 5-2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation of accessories 5-2 . . . . . . . . . . . . . . . . . . . . . . .
Audio set 5-3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Type A audio set 5-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Type B audio set 5-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
In-dash 6 CD auto changer 1 (Optional audio unit – if equipped) 5-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Type A audio set (if equipped) 5-5 . . . . . . . . . . . . . . . . .
Radio operation 5-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compact disc player operation 5-10 . . . . . . . . . . . . . . . . .
CD changer control (If optional in-dash CD
changer is connected) 5-12 . . . . . . . . . . . . . . . . . . . . . . . . . .
Type B audio set (if equipped) 5-16 . . . . . . . . . . . . . . . . .
Radio operation 5-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cassette player operation 5-22 . . . . . . . . . . . . . . . . . . . . . . . .
Built in CD changer operation 5-26 . . . . . . . . . . . . . . . . . . .
In-dash 6 CD auto changer 1 (if equipped) 5-31 .
Loading and unloading compact discs 5-31 . . . . . . . .
Precautions to observe when handling
a compact disc (CD) 5-34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio

Audio
5-3
– CONTINUED –
Audio set
Your SUBARU may be equipped with one of the fol- lowing audio sets. See the pages indicated in thissection for operating details. Type A audio set
Radio operation: refer to page 5-5
Compact disc player operation: refer to page 5-10
CD changer control: refer to page 5-12
Type B audio set
Radio operation: refer to page 5-16
Cassette player operation: refer to page 5-22
Built-in CD changer operation: refer to page 5-26

Audio
5-4
In-dash 6 CD auto changer 1 (Optional audio unit – if equipped)
Inserting and removing a disc or all discs: refer to
page 5-31

Audio
5-6
Power switch and volume/bass/treble/fader/ balance control (PWR/VOL)
The dial (2) is used for both power (ON/OFF) and
volume control. The radio is turned ON and OFF by
pushing the dial and the volume is controlled by
turning the dial.
n Tone and balance control
The “VOLUME” control knob normally function as
volume control. This knob become a control for
Treble, Bass, Fader or Balance when you select the
appropriate audio mode.
Choose desired volume level for each mode by turn-ing the “VOLUME” control knob. The control function
returns to volume control mode after about 5seconds. To change control modes
: Each brief press of the
“T/B” button changes control modes in the following
sequence starting from volume control mode. (When
the radio is first turned on, the control mode is in the
volume control.)
Volume(VOL)
Bass (BAS) Treble(TRE)
Fader
(FAD)
Balance(BAL)