2003 SUBARU FORESTER service indicator

1-61
Seat, seatbelt and SRS airbags
–CONTINUED –
Airbag control module (including impact sensors)
Frontal airbag module (Driver’s side)
Frontal airbag module (Passenger’s side)
Side airbag sensor (Driver’s side – if equipped)
Side airbag sensor (Passenger’s side – if equipped)
Side airbag module (Driver’s side – if equipped)
Side airbag module (Passenger’s side – if
equipped) Seatbelt pretensioner (Driver’s side)
Seatbelt pretensioner (Passenger’s side)
All related wiring
In the event of a malfunction indicated by any of follow-
ing, the vehicle should be taken promptly to your near-
est SUBARU dealer to have the system checked.
Unless checked and repaired, the SRS airbags will not
function reliably: Flashing or flickering of the indicator light.
No illumination of the warning light when the ignition
switch is first turned to the “ON” position. Continuous illumination of the warning light.
Illumination of the warning light while driving.
SRS airbag system servicing
When discarding an airbag module or scrap- ping the entire car damaged by a collision, con-
sult your SUBARU dealer.
The SRS airbag has no user-serviceable
parts. Do not use electrical test equipment on
any circuit related to the SRS airbag system.
For required servicing of the SRS airbag, see
your nearest SUBARU dealer. Tampering with
or disconnecting the system

7-8
Starting and operating
or there is one or more diagnostic trouble codes stored
in vehicle’s computer with the
“CHECK ENGINE”
warning light/MIL illuminated. A state emission inspection may reject (not pass or
fail) a vehicle if the number of OBD system readiness
monitors “Not Ready” is greater than three. Under
this condition, the vehicle operator should be instruct-
ed to drive his/her vehicle for a few days to set the
monitors and return for an emission re-inspection. Owners of rejected or failing vehicles should contact
their Subaru Dealer for service.Preparing to drive
You should perform the following checks and adjust-
ments every day before you start driving.
1. Check that all windows, mirrors, and lights are
clean and unobstructed.
2. Check the appearance and condition of the tires.
Also check tires for proper inflation.
3. Look under the vehicle for any sign of leaks.
4. Check that the hood and rear gate are fully closed.
5. Check the adjustment of the seat.
6. Check the adjustment of the inside and outside mir-
rors.
7. Fasten your seatbelt. Check that your passengers
have fastened their seatbelts.
8. Check the operation of the warning and indicator
lights when the ignition switch is turned to the “ON” po-sition.
9. Check the gauges, indicator and warning lights af-
ter starting the engine.
NOTE
Engine oil, engine coolant, brake fluid, washer flu-
id and other fluid levels should be checked daily,
weekly or at fuel stops.

11 - 2
Maintenance and service
Tire inspection ................................................. 11-38
Tire pressures and wear ................................. 11-38
Wheel balance .................................................. 11-41
Wear indicators ................................................ 11-41
Tire rotation ...................................................... 11-42
Tire replacement .............................................. 11-43
Wheel replacement .......................................... 11-43
Aluminum wheels (If equipped) ................. 11-44
Windshield washer fluid ............................. 11-45
Replacement of windshield wiper blades . 11-46
Battery .......................................................... 11-49
Fuses ............................................................ 11-50
Main fuse ...................................................... 11-53
Installation of accessories ......................... 11-53
Replacing bulbs ........................................... 11-54 Headlight .......................................................... 11-55
Front turn signal, side marker light and
parking lights ................................................... 11-57
Front fog light .................................................. 11-61
Rear combination lights .................................. 11-61
License plate light ........................................... 11-62
Dome light, map light and cargo area light ... 11-63
High mount stop light ..................................... 11-64

11 -3 5
Maintenance and service
–CONTINUED –
Hill holder (MT vehicles — if
equipped)
Ensure that the hill holder operates properly under the
following circumstances:
1. Stop the vehicle on an uphill grade by depressing
the brake pedal and clutch pedal, with the engine run-
ning.
2. Make sure that the vehicle does not move back-
ward even after the brake pedal is released.
3. Then make sure the vehicle starts climbing the
grade by following the normal starting procedures.
If the hill holder does not operate as described above,
contact with your SUBARU dealer.
Replacement of brake pad and lining
The front disc brakes and the right rear disc brake
have an audible wear indicators on the brake pads. If
the brake pads wear close to their service limit, the
wear indicator makes a very audible scraping noise
when the brake pedal is applied.
If you hear this scraping noise each time you apply the
brake pedal, have the brake pads serviced by your
SUBARU dealer as soon as possible.
HS7012BA