2003 SUBARU FORESTER fog light

4-7
Climate control
– CONTINUED –
Heating and defrosting
To direct warm air toward the floor and the windshield:
1. Set the air flow control dial to the “ ”position.
2. Set the temperature control dial to the most com-
fortable level.
3. Set the fan speed control dial to the desired speed.
If your vehicle is equipped with an air conditioner,
when the “ ” or “ ” position is selected, the air
conditioner compressor automatically operates re-
gardless of the position of the air conditioner button to
defog the windshield quickly.
However, the air conditioner indicator light does not
come on at this time.NOTE
Warm air also comes out from the right and left air
outlets. To stop warm air flow from these outlets,
turn the corresponding thumb-wheel down. Heating
To direct warm air toward the floor:
1. Set the air inlet selection button to the OFF position
2. Set the air flow control dial to the “ ” position.
3. Set the temperature control dial to the most com-
fortable level.
4. Set the fan speed control dial to the desired speed.
HS4014AA
HS4015AA

4-10
Climate control

Defrosting or defogging
To direct warm air to the windshield and front door win-
dows:
1. Set the air flow control dial to the “ ” position.
2. Set the temperature control dial to the red side.
3. Set the fan speed control dial at the highest speed.
The air conditioner compressor automatically oper-
ates when the air flow control dial set in the “ ” or
“ ” position to provide better defogging perfor-
mance.
However, the air conditioner indicator light does not
come on at this time. Automatic climate control system (if
equipped)
NOTE
Operate the automatic climate control system
when the engine is running. When the engine coolant is cold, the blower
does not run. In the “AUTO” mode, when the air temperature
in the passenger compartment is sufficiently cool,
the air conditioner compressor does not operate.
For efficient defogging or dehumidifying in cold
weather, press the “A/C” switch on. Even when cooling is not necessary, setting the
temperature much lower than the current outlet air
temperature turns on the air conditioner compres-
sor automatically and the “A/C” indicator light on
the control panel comes on.
The automatic climate control system automatically
controls outlet air temperature, fan speed, air flow dis-
tribution air-inlet control, and air conditioner compres-
sor operation. It activates when the “AUTO” switch is
pressed, and is used in conjunction with the Temper-
ature control dial to maintain a constant, comfortable
climate within the passenger compartment.
The temperature can be set within a range of 65 –
HS4013AA

4-11
Climate control
– CONTINUED –
85°F(18–32 °C).
NOTE
The temperature is shown in units of Fahrenheit
for the US model and in Centigrade for the Canadi-
an model. Control panel
1) Temperature control dial
2) AUTO switch
3) Fan speed control dial
4) Air conditioner switch
5) Air flow control dial
6) Defroster switch
7) Rear window defogger switch (Refer to the “Rear win- dow defogger switch” in chapter 3.)
8) Air inlet selection switch
9) OFF/BRIGHT switch
AUTO switch
AUTO mode operation:
When the “AUTO” switch is pressed, the indicator light
on the switch illuminates, indicating that the Automatic
Climate Control system is operating in the automatic
mode. In the automatic mode, the system maintains
the desired cabin air temperature (this is set using the
temperature control dial) by automatically controlling
the fan speed, air flow mode, air inlet selection, and air
conditioner compressor operation.
123456
7
8
9
HS4019BB
HS4023BA

4-13
Climate control
– CONTINUED –
— Defroster switch
To defrost or dehumidify the windshield and side win-
dows, push the defroster switch “ ”. When the
“ ” switch is pushed, regardless whether the air
conditioner is operating or not, outside air is drawn into
the passenger compartment, the air conditioner com-
pressor turns on, air flow is directed towards the wind-
shield and side windows, and the indicator light on the
switch comes on.
After eliminating the fogging from the windshield, re-
turn the climate control system to the AUTO mode by
pushing the “AUTO” switch or turn off by pushing the
“OFF” switch.
Alternatively, push the “ ” switch again to return the system to the setting that was selected before you
activated the defroster.
Fan speed control dial
The fan operates only when the ignition switch is in the
“ON” position. Select any of the four fan speeds by
turning the fan speed control dial. The selected fan
speed is indicated by illumination of the corresponding
indicator light around the dial.
HS4021CA
HS4020AA

4-14
Climate control

A/C — Air conditioner switch
If the windshield starts to fog when the climate control
system is operated in the AUTO mode, push the air
conditioner switch “A/C” to defog and dehumidify.
When this switch is pushed, the air conditioner com-
pressor turns on and the indicator light comes on. Af-
ter eliminating the fogging from the windshield, set the
system back to the AUTO mode by pushing the “AU-
TO” switch.
NOTE
The air conditioner compressor does not operate
when the outside air temperature is below 32 °F
(0 °C).
Air flow control dial
Select the desired air flow mode by turning the air flow
control dial. The selected air flow mode is indicated by
illumination of the corresponding indicator light around
the dial. (Ventilation): Air flows through the instrument panel
outlets.
(Bi-level): Air flows through the instrument panel
outlets and the foot outlets.
(Heat): Air flows through the foot outlets and some
through the windshield defroster outlets.
HS4020DAHS4021AA

4-15
Climate control
– CONTINUED –
(Heat-def): Air flows through the windshield de-
froster outlets and foot outlets. Air inlet selection switch
Select air flow by pushing the air inlet selection switch “” .
ON (Recirculation): Interior air recirculates inside the
passenger compartment. Use this position when
quickly cooling down the passenger compartment or
to prevent outside air from entering the passenger
compartment. The indicator light comes on when the
“Recirculation” mode is selected.
OFF (Outside air): Outside air is drawn into the pas-
senger compartment. When the climate control sys- tem is operated in the “AUTO” mode, this position is
selected automatically. The indicator light goes off
when the “Outside air” mode is selected.
Continued operation in the ON position may fog
up the windows. Switch to the OFF position as
soon as the outside dusty condition clears.
Temperature sensors
1) Interior air temperature sensor
2) Solar sensor
HS4020CA
1 2HS4028BB

11 - 2
Maintenance and service
Tire inspection ................................................. 11-38
Tire pressures and wear ................................. 11-38
Wheel balance .................................................. 11-41
Wear indicators ................................................ 11-41
Tire rotation ...................................................... 11-42
Tire replacement .............................................. 11-43
Wheel replacement .......................................... 11-43
Aluminum wheels (If equipped) ................. 11-44
Windshield washer fluid ............................. 11-45
Replacement of windshield wiper blades . 11-46
Battery .......................................................... 11-49
Fuses ............................................................ 11-50
Main fuse ...................................................... 11-53
Installation of accessories ......................... 11-53
Replacing bulbs ........................................... 11-54 Headlight .......................................................... 11-55
Front turn signal, side marker light and
parking lights ................................................... 11-57
Front fog light .................................................. 11-61
Rear combination lights .................................. 11-61
License plate light ........................................... 11-62
Dome light, map light and cargo area light ... 11-63
High mount stop light ..................................... 11-64

11 -5 3
Maintenance and service
–CONTINUED –
Main fuse
Main fuse box
The main fuses are designed to melt during an over-
load to prevent damage to the wiring harness and
electrical equipment. Check the main fuses if any elec-
trical component fails to operate (except the starter
motor) and other fuses are good. A melted main fuse
must be replaced. Use only replacements with the
same specified rating as the melted main fuse. If a
main fuse blows after it is replaced, have the electrical
system checked by your nearest SUBARU dealer.Installation of accessories
Always consult your SUBARU dealer before installing
fog lights or any other electrical equipment in your ve-
hicle. Such accessories may cause the electronic sys-
tem to malfunction if they are incorrectly installed or if
they are not suited for the vehicle.
HSB065BA