2003 SUBARU BAJA spare wheel

Driving tips8-7
–
CONTINUED –
ing. Therefore, when driving down a slope or turning corners, be sure to
reduce your speed and maintain an ample distance from other vehicles.When replacing a tire, make sure you use only the same size, circum-
ference, construction, brand, and load range as the original tires listed on
the tire placard. Using other sizes, circumferences or construction may re-
sult in severe mechanical damage to the drive train of your vehicle and
may affect ride, handling, braking, speedometer/odometer calibration, and
clearance between the body and tires. It also may be dangerous and lead
to loss of vehicle control. If you use a temporary spare tire to replace a flat tire, be sure to use
the original temporary spare tire stored in the vehicle. Using other sizes
may result in severe mechanical damage to the drive train of your vehicle. Always check the cold tire pressure before starting to drive. The rec-
ommended tire pressure is provided on the tire placard, which is locatedunder the door latch on the driver ’s side.
Tire chains should always be placed on the front wheels only.
There are some precautions that you must observe when towing your
vehicle. For detail information, see “Towing” section in Chapter 9.
Off road driving
WARNING
Always maintain a safe driving speed according to the road
and weather conditions in order to avoid having an accident on asharp turn, during sudden braking or under other similar condi-tions. Always use the utmost care in driving – overconfidence
because you are driving an all wheel drive vehicle could easilylead to a serious accident.
Because of the AWD feature and higher ground clearance, your Subaru
can be driven on ordinary roads or off-road. But please keep in mind that
an AWD Subaru is neither a conventional off-road vehicle nor an all-ter-
rain vehicle. If you do take your Subaru off-road, certain common sense
precautions such as the following should be taken:

Driving tips8-15
–
CONTINUED –
When driving with tire chains, drive at speeds below 19 mph (30 km/h).
When a temporary spare tire is on a front wheel, replace the temporary
spare tire with the rear tire on the same side of the vehicle, and then fit
chains on the front tires.
Always use the utmost care when driving with tire chains – overconfi-
dence because you are driving with tire chains could easily lead to a se-rious accident. Rocking the vehicle
If you must rock the vehicle to free it from snow, sand, or mud, depress the
accelerator pedal slightly and move the selector lever back and forth be-
tween “D” and “R” repeatedly. Do not race the engine. For the best possible
traction, avoid spinning the wheels when trying to free the vehicle.
When the road surface is extremely slippery, you can obtain better trac-
tion by starting the vehicle with the transmission in 2nd than 1st (both for
MT and AT). Refer to the “Automatic transmission ” section in Chapter 7 for information
on holding the transmission in 2nd position.
Loading your vehicle
WARNING
Never allow passengers to ride on the folded rear seatback or
in the cargo bed. Doing so may result in serious injury. Never stack luggage or other cargo higher than the top of the
seatback because it could tumble forward and injure passengersin the event of a sudden stop or accident. Keep luggage or cargo
low, as close to the floor as possible. When you carry something inside the vehicle, secure it when-
ever you can to prevent it from being thrown around inside the
vehicle during sudden stops, sharp turns or in an accident. Do not pile heavy loads on the roof. These loads raise the
vehicle’ s center of gravity and make it more prone to tip over.

9-6
NOTE
Confirm no looseness exists after securing the jack. Looseness may cause a rattle while the vehicle is moving.CAUTION
After the jack and the tool bag have been restored in the rearquarter pocket, make sure that the rear seatback has been
securely locked. When securely locked, the red marks on thelocking knobs are no longer visible.
Spare tire
HB9053BA
The spare tire is stored in the spare tire holder located under the rear of the cargo bed.
The spare tire holder has a hoist mechanism that can lower and raise the
spare tire easily. The spare tire holder is designed to carry only the tem-
porary spare tire that comes with your vehicle.
Before using the temporary spare tire, see the “Temporary spare tire ”
section in this Chapter for instructions and precautions.
Removing the spare tire
1. Take the wheel nut wrench out of the tool bag. Refer to the “Jack
and tools ” section in this Chapter for its storage location.

In case of emergency9-7
–
CONTINUED –
HB9054BA
2. Open the tailgate and remove the rubber cap from the cargo bed. Pull up the “RELEASE” portion of the cap when removing it.
3. Locate the hex-headed hoist shaft end inside the hole.
HB9055BA
4. Turn the hoist shaft end counterclockwise with the wheel nut
wrench until the temporary spare tire is on the ground with enough
cable slack to allow you to pull it out from under the vehicle.
CAUTION
Do not put your fingers into the center hole of the temporaryspare tire while you pulling it out, because they might be pinched
in between the wheel and the retainer.

In case of emergency9-9
–
CONTINUED –
Re-storage of spare tire
1. Turn the spare tire hoist shaft end counterclockwise with the wheel
nut wrench to loosen the cable sufficiently enough to allow the cable
end retainer go through center hole of the temporary spare tire.
2. Insert the retainer through the center hole of the temporary tire
(with the outside of the tire facing up).
3. Turn the hoist shaft end clockwise with the wheel nut wrench towind the cable up completely until you hear a few clicking sounds.
Confirm that the temporary spare tire holding cable has been wound
up completely by shaking the temporary tire.
CAUTION
If the temporary spare tire is not stored securely, it could damage
adjacent areas of the vehicle and make an abnormal noise.
4. Put the rubber cap on the hoist shaft end hole.
5. Place the wheel nut wrench back into the tool bag and store thejack and tool bag in their storage locations.
Temporary spare tire Using the temporary spare tire
WARNING
Never tow a trailer when the temporary spare tire is used. The temporary spare tire is not designed to sustain the towing load.
Use of the temporary spare tire when towing can result in failureof the spare tire and/or less stability of the vehicle and may leadto an accident.
CAUTION
Never use any temporary spare tire other than the original. Usingother sizes may result in severe mechanical damage to the drivetrain of your vehicle.

9-10
The temporary spare tire is smaller and lighter than a conventional tire
and is designed for emergency use only. Remove the temporary spare
tire and re-install the conventional tire as soon as possible because the
spare tire is designed only for temporary use.
Check the inflation pressure of the temporary spare tire periodically to
keep the tire ready for use. The correct pressure is 60 psi (420 kPa, 4.2
kg/cm 2
).
When using the temporary spare tire, note the following: Do not exceed 50 mph (80 km/h).
Do not put a tire chain on the temporary spare tire. Because of the
smaller tire size, a tire chain will not fit properly. Do not use two or more temporary spare tires at the same time.
Do not drive over obstacles. This tire has a smaller diameter, so
road clearance is reduced. When the wear indicator appears on the tread, replace the tire.
HB8003BB
HG0106
Indicator location mark
Tread wear indicator bar
NOTE [Automatic transmission vehicle] Before driving your vehicle with the temporary spare tire, put a spare fuse inside the FWD connectorlocated in the engine compartment and confirm that the Front-wheeldrive warning light comes on. The all wheel drive capability of the
vehicle has now been deactivated. After re-installing the convention-al tire, remove the spare fuse from the FWD connector in order to
reactivate all wheel drive.

9-12
HGS038BA
4. Put wheel blocks at the front and rear of the tire diagonally opposite
the flat tire.
5. Take out the spare tire, jack, and wheel nut wrench. Refer to the sections “Spare tire ” and “Jack and tools ” in this chapter for
their location, instructions and precautions.
After the spare tire is removed from the spare tire holder, the cable must
be wound up completely by turning the hoist nut shaft clockwise until
you hear a clicking sound. Also visually inspect the cable to make cer-
tain that there is no longer any slack present.
Removing the flat tire and installing the spare tire
HS9008BA
1. Loosen the wheel nuts using the wheel nut wrench but do not re- move the nuts.

9-14
HB9060BA
4. Insert the jack drive tube into the jackscrew and attach the wheel
nut wrench into the jack drive tube, and turn the handle until the tire
clears the ground. Do not raise the vehicle higher than necessary.
5. Remove the wheel nuts and the flat tire.
HG0104
OM-H0172
6. Before putting the spare tire on, clean the mounting surface of the wheel and hub with a cloth.
7. Put on the spare tire. Replace the wheel nuts. Tighten them byhand.
WARNING
Do not use oil or grease on the wheel studs or nuts when the
spare tire is installed. This could cause the nuts to become looseand lead to an accident.