2003 SUBARU BAJA ac lock up

1-6
Reclining the seatback
HB1072BA
Pull the reclining lever up and adjust the seatback to the desired posi-
tion. Then release the lever and make sure the seat is securely locked
into place.
The seatback placed in a reclined position can spring back upward
with force when released. When operating the reclining lever to return
the seatback, hold it lightly so that it may be raised back gradually. Head restraint adjustment
HB1016BA
To raise the head restraint, pull it up. To lower it, push the head
restraint down while pressing the release button on the top of theseatback.
The head restraint should be adjusted so that the center of the head
restraint is closest to the top of the occupant ’s ears.

Seat, seatbelt and SRS airbags1-9
–
CONTINUED –
To avoid the possibility of serious injury or death, passengers
must never be allowed to sit on the rear center console while the
vehicle is in motion. The rear seat of this vehicle is designed forno more than two passengers and is equipped with only two seat-belts. Make sure that the rear seatback is securely locked. When it is
securely locked, the red marking on the lock is no longer visible.If it is not locked, the seatback may move forward when the ve-hicle is operated. Secure skis and other lengthy items properly to prevent them
from being thrown around inside the vehicle and causing serious
injury during a sudden stop, a sudden steering or a rapid accel-eration.
HB0302
Sit well back and upright.

1-10
Rear headrest
HB1153AA
Rear headrest are hot adjustable, nor removable. Folding down the rear seat
WARNING
After returning the rear seat to its original position, be certain
to place all of the seatbelts and the tab attached to the seat cush- ion above the seat cushion. And make certain that the shoulderbelts are fully visible. Make sure that the rear seatback is securely locked after
returning the seatback to its original position. When securely
locked, the red marking on the lock is no longer visible. If it is not
locked securely, the rear seatback may fold down during driving.

Seat, seatbelt and SRS airbags1-11
–
CONTINUED –
Folding down the seatback
HB1110BA
HB1109BB
1. Unlock the seatback by pulling the release knob up and then fold the seatback down. Folding down the seat cushion and seatback
1. Move the front seat forward.
2. Store the seatbelts in the seatbelt pockets to prevent them from fal-ling below the cushion.
HB1111BA
3. Raise the seat cushion by pulling up the tab.

1-12
HB1112BAHB1109CA
4. Unlock the seatback by pulling the release knob up and fold the
seatback down. Confirm that the pin located at the bottom of the seat
cushion is inserted into the slot at the top of the seatback.
CAUTION
Be careful not to pinch your hand or fingers with the seat cushionor the seatback when performing the fold down operation.
HB1113BAHB1112CB
CAUTION
Confirm that the rear seatbelts are stored in the seatbelt pocket prior to returning the seat cushion to its original position.

Seat, seatbelt and SRS airbags1-13
–
CONTINUED –
5. To return the rear seat to its original position, raise the seatback
and seat cushion until they lock into place and make sure that they
are securely locked.
Make sure that the rear seatbelt buckles are not under the seat cush-
ion or seatback, when returning the seat cushion and the seatback totheir original position.

1-16
Expectant mothers also need to use the seatbelts. They should con-
sult their doctor for specific recommendations. The lap belt should be
worn securely and as low as possible over the hips, not over thewaist.
Emergency Locking Retractor (ELR)
The driver ’s seatbelt has an Emergency Locking Retractor (ELR).
The emergency locking retractor allows normal body movement but the
retractor locks automatically during a sudden stop, impact or if you pull
the belt very quickly out of the retractor. Automatic/Emergency Locking Retractor (A/ELR)
Each passenger ’s seatbelt has an Automatic/Emergency Locking Re-
tractor (A/ELR). The Automatic/Emergency Locking Retractor normally
functions as an Emergency Locking Retractor (ELR). The A/ELR has an
additional locking mode “Automatic Locking Retractor (ALR) mode ” in-
tended to secure a child restraint system. When the seatbelt is once
drawn out completely and is then retracted even slightly, the retractorlocks the seatbelt in that position and the seatbelt cannot be extended.
As the belt is rewinding, clicks will be heard which indicate the retractor
functions as ALR. When the seatbelt is retracted fully, ALR mode is re-leased.
When securing a child restraint system on the passengers ’ seats, the
seatbelt must be changed over to the Automatic Locking Retractor (ALR) mode.
When the child restraint system is removed, make sure that the retractor
is restored to the Emergency Locking Retractor (ELR) function by allow-
ing the seatbelt to retract fully.
For instructions on how to convert the retractor to the ALR mode and re-
store it to the ELR mode, see the “Child restraint systems ” section in this
chapter. Seatbelt warning light and chime
Your vehicle is equipped with a seatbelt warning device at the driver ’s
seat.

Seat, seatbelt and SRS airbags1-19
–
CONTINUED –
2. Sit well back in the seat.
3. Pick up the tongue plate and pull the belt out slowly. Do not let it
get twisted. If the belt stops before reaching the buckle, return the
belt slightly and pull it out more slowly. If the belt still cannot be
unlocked, let the belt retract slightly after giving it a strong pull, thenpull it out slowly again.
4. Insert the tongue plate into the buckle until you hear a click.
5. To make the lap part tight, pull up on the shoulder belt. And placethe lap belt as low as possible on your hips, not on your waist. nAdjusting the front seat shoulder belt anchor height
WARNING
When wearing the seatbelts, make sure the shoulder portion of the webbing does not pass over your neck. If it does, adjust the
seatbelt anchor to a lower position. Placing the shoulder beltover the neck may result in neck injury during sudden braking orin a collision.
HB1029BB
The shoulder belt anchor height should be adjusted to the position
best suited for you. To lower the anchor height, push the release but-
ton and slide the anchor down. To raise the anchor height, slide the
anchor up. Pull down on the anchor to make sure that it is locked inplace.