2003 SSANGYONG MUSSO oil temperature

1B2-100 M161 ENGINE MECHANICAL9. Fill up engine oil through the engine oil filler opening.
10. Check for oil leaks at normal engine temperature after starting the engine.
11. Stop the engine and wait 5 minutes. Check the oil level and fill up as specified if necessary.
4. Remove the drain plug (1) and drain the engine oil.
Notice Leave the oil filler cap (3) open to ease the engine oil discharge.
5. Tighten the engine oil drain plug after cleaning it. Installation Notice
Tools Required
103 589 02 09 00 Oil Filter Socket Wrench Replacement Procedure
1. Install the socket wrench ”7” (special tool : 103 589 02 09
00) on the oil filter cover (2). NoticeMake the screw cover removable by tightening the bolt at the side of the socket wrench (special tool).
2. Install the wrench to the upper bolt in the socket wrench and remove the oil cover by turning it.
3. Remove the oil filter element.
Notice Work with a cloth under the vehicle when removing the oil filter element to not drain the oil. Replace the seal washer with new one.
6. Replace the O-ring(5) in the oil filter cover with new one.
Notice Apply the engine oil to the O-ring.
7. Insert new oil filter element into the oil filter housing.
Tightening Torque 25 Nm
8. Temporarily tighten the oil filter cover (2). Install the socket wrench “7” (special tool : 103 589 02 09 00), and then
completely tighten it. Installation Notice
2 Oil Filter Cover
5 O-ring
6 Oil Filter Element
7 Special Tool (Socket Wrench)
Tightening Torque 25 Nm

1B3-44 OM600 ENGINE MECHANICAL
22. Remove the cable channel.
23. Disconnect the cables from the glow plug sensor andcoolant temperature sensor.
24. Remove the heater pipe bracket from the oil filter.
25. Pry off the clamp and push the heater feed pipe forward and then pull out the pipe.

OM600 ENGINE ELECTRICAL 1E3-3
1. Preheating time - control relay.Control relay functions as followings :
Switching of preheating current.
Indication of preheating finish.
Control of preheating sequence.
Indication of fault.
2. Coolant temperature sensor. Coolant temperature sensor senses coolant ’s temperature
and signals it to the preheating relay continuously.
3. Glow plug The glow plug parts are housing with M12 ´ 1.25 thread
and heating pin in housing. It is connected in a parallel circuit
with the specified voltage of 11.5V. The heating element has a heating coil and a control coil and they are connected in series.
1. Control Coil 2. Heater Coil
4. Current and temperature of glow plug Current of glow plug While the preheating system operates, current of about
30A flows in each glow plug and temperature of heating coil rises very fast.
Due to the rise of temperature, the resistance of control
coil increases therefore the current is controlled to
about 8~15A and that protects the glow plug from over-
heating.
Temperature of glow plug The temperature of the glow plug reaches up to 900 °C
after about 9 seconds and up to 1,050 °C after 30
seconds.

M162 ENGINE CONTROLS 1F1-7
41 44455657 58 59606264 65 66677172 73 74757677 78 79808182 83 86 8789
0001 02 0304 05 08091011 17 1819 20 21 2324 25 26272930 31 34 3540
Failure
code Description
Coolant temperature sensor open Coolant temperature sensor shortCoolant temperature sensor signal failureIntake temperature sensor openIntake temperature sensor short Intake temperature sensor signal failure Low battery voltageHFM sensor signal failureHFM sensor signal failure(Low)HFM sensor signal failure(High) Crankshaft position sensor signal failure (no engine revolution signal)Crankshaft position sensor signal failure(rpm > max. value)No.1 cylinder recognition failure Crankshaft position sensor signal failure (gab recognition failure)
Transmission coding failureCAN communication failure : ASR-
Transponder signal failure CAN communication failure : TCU(A/T only)CAN communication failure : TOD(E32 only)-- CAN communication failure : communication initialization failureFuel pump relay short(PWR)Fuel pump relay open/short(GND)Purge valve short
Fa
ilure
code Description
Purge valve open/short Condenser fan(HI) relay short(PWR)Condenser fan(HI) relay short(GND)No.1 knock sensor signal failureNo.2 knock sensor signal failure No.1 cylinder synchronization failure --Cluster S/W defectaveNo ignition voltage output(No.1 ignition coil) No ignition voltage output(No.2 ignition coil) No ignition voltage output(No.3 ignition coil)Crankshaft position sensor adaptation failureStart signal recognition failureNo.1 injector short(PWR) No.1 injector open/short(GND) No.2 injector short(PWR)No.2 injector open/short(GND)No.3 injector short(PWR)No.3 injector open/short(GND) No.4 injector short(PWR) No.4 injector open/short(GND)High oxygen sensor voltageLow oxygen sensor amplifying voltageOxygen sensor operating failure Not excessive lean indication in oxygen sensor(during coasting)Oxygen sensor heater short(PWR)Oxygen sensor heater open/short(GND)Low oxygen sensor voltage
SELF DIAGNOSIS FAILURE CODE

M162 ENGINE CONTROLS 1F1-39
Engine Connector
Pin No.Abbreciation
Decription
61 62636465666768697071727374757677787980 EV5EV6EV1EV4EV2EV3
M+M-
TM.31
ZSC16 ZSA25ZSB34 NWS ----
MT
GND LT
Injector-cylinder 2Injector-cylinder 4Injector-cylinder 1Injector-cylinder 6Injector-cylinder 5Injector-cylinder 3E-GAS motor plusE-GAS motor minusPower ground TM.31Ignition coil cylinder 1+6Ignition coil cylinder 2+5Ignition coil cylinder 3+4Camshaft control----Engine coolant temperature
Temperature groundIntake air temperature

M162 ENGINE CONTROLS 1F1-43
Pin No.
61 626364 65 666768 69 70 71727374 75 7677787980 81 82838485 86 87888990
Description
Injector-cylinder 2 Injector-cylinder 4Injector-cylinder 1Injector-cylinder 6 Injector-cylinder 5 Injector-cylinder 3E-GAS motor plusE-GAS motor minus Power ground TM.31 Ignition coil cylinder 1+6 Ignition coil cylinder 2+5Ignition coil cylinder 3+4Camshaft control- - --Engine coolant temperature
Temperature groundIntake air temperature Hot film air mass signal --E-GAS potentiometer groundE-GAS potentiometer 2 signal - E-GAS potentiometer 1 signal---EV5 EV6EV1EV4 EV2 EV3M+M-
TM.31
ZSC16
ZSA25ZSB34 NWS - - --
MT
GND LT
HFM
--
GND IP2S -
IP1S ---












- - --



--

-
- - -












- - --



- -

-
--- Remarks
Abbreviation E32 ENG,
5speed M/T
E32 ENG,
4speed A/T (BTRA)

FrontRear
Front Rear
SECTION 4F
ANTILOCK BRAKE SYSTEM
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting thiscable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCKunless otherwise noted.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application Model
ECUNumber of Pins
Operating TemperatureMotor Operating CurrentSolenoid Coil Resistance External Resistance Air Gap
Number of teeth Description
ABS 5.3 31
-40 ~ +120 °C
Below MAX 40A
1.28K - 1.92K
0.35 - 1.60 mm 0.15 - 1.20 mm 52 52 ABS/ABD 5.3
83
-40 ~ +85 °C
Below MAX 45A
8.04 - 9.04 except AV,
HSV 4.04 - 4.54
1.28K - 1.92K
0.35 - 1.60 mm 0.15 - 1.20 mm
52 52
Hydraulic System
Wheel Speed Sensor Impulse Ring
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4F-1
General Specifications . . . . . . . . . . . . . . . . . . 4F-1
Schematic and Routing Diagrams . . . . . . . . 4F-2 ABS 5.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-2
ABS/ABD 5.0 . . . . . . . . . . . . . . . . . . . . . . . . . 4F-3
ABS 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-4
ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . 4F-5
Component Locator . . . . . . . . . . . . . . . . . . . 4F-6 ABS, ABS/ABD . . . . . . . . . . . . . . . . . . . . . . . . 4F-6
ABD System Description . . . . . . . . . . . . . . . 4F-7 Self Diagnosis . . . . . . . . . . . . . . . . . . . . . . . 4F-9
ABS, ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . 4F-9
ABS, ABS/ABD 5.0 . . . . . . . . . . . . . . . . . . . . 4F-11
Defect Codes . . . . . . . . . . . . . . . . . . . . . . . . 4F-13
Maintenance and Repair . . . . . . . . . . . . . . 4F-19
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 4F-19
Wheel Speed Sensor . . . . . . . . . . . . . . . . . . 4F-19
Hydraulic Circuit . . . . . . . . . . . . . . . . . . . . 4F-21 ABS 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-21
ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . . . . 4F-24

AUTOMATIC TRANSMISSION 5A-25
producing a low resistance.
Temperature/Resistance characteristics and location within the solenoid wiring loom are given in tables 3-1 and 3- 2, and figures 3.2 and 3.3.
If the transmission sump temperature exceeds 135°C, the TCU will impose converter lock-up at lower vehicle
speeds and in some vehicles flashes the mode indicator lamp. This results in maximum oil flow through the
external oil cooler and eliminates slippage in the torque converter. Both these actions combine to reduce the oil
temperature in the transmission.
Connects To
Solenoid 1 Solenoid 2Solenoid 3Solenoid 4Solenoid 5 Solenoid 6 Solenoid 7Solenoid 5
Temp Sensor
Temp SensorWire Color Red
Blue
Yellow
Orange GreenViolet
Brown
Green White WhitePin No.
1 2345 6 789
10
Table 3.2 - Pin No. Codes for Temperature Sensor Location In Solenoid Loom
Figure 3.3 - Temperature Sensor Location in Solenoid Loom