2003 Peugeot 307 CC warning

22-09-2003
YOUR 307 CC IN DETAIL95
THE ALARM This provides two types of protec- tion: Ð
exterior protection: it sounds if a
door, the boot or the bonnet is opened.
Ð interior protection: it sounds if
the volume inside the passengercompartment changes (breaking ofa window or a movement insidethe vehicle).
Note: the interior protection alarm
does not function if the vehicle's roofis open (cabriolet position). Setting the alarm  Switch off the ignition and get out of the vehicle.
 Set the alarm by locking or dead-locking using the remote control(button Aindicator light flashes
once per second).
Note: if you wish to lock your vehicle
without setting the alarm, use thedoor lock. When the alarm is triggered, thesiren sounds and the direction indi-cator lights flash for thirty seconds. After triggering, the alarm remains set.
Warning:
if the alarm has been trig-
gered ten times in succession, on the eleventh time it becomes inac-tive. Note: if button Aindicator light flash-
es rapidly, the alarm has been trig- gered while you were away fromyour vehicle. Disarming Unlock the vehicle with the remote control key (button Aindicator light
goes out). Note: if the alarm has been triggered
while you were away from your vehi- cle, the rapid flashing of the indicatorlight will stop when you switch on theignition.
To set the alarm with exterior protection only If, while you are away from the vehi- cle, you wish to leave a window par-tially open or a pet inside the vehicle,you should choose exterior protec-
tion only.  Switch off the ignition,
 In the next ten seconds, press button Auntil the indicator light is
on continuously,
 Get out of the vehicle, 
Set the alarm by locking or dead-locking using the remote control(button Aindicator light flashes
once a second).
Note: when the alarm is set but the
remote control does not operate:  Unlock the door with the key and
open it. The alarm is triggered.
 Switch on the ignition. The alarmis disarmed.
Incorrect operation When the ignition is switched on, if button Alights for ten seconds, there
is a fault in the siren connection.
Contact a PEUGEOT dealer to have the system checked. Automatic activation* The alarm is activated automatically two minutes after the last closure ofa door or the boot. In order to avoid accidental triggering of the alarm when a door or the bootis opened, it is essential to first pressthe unlocking button on the remotecontrol.
* According to destination.

22-09-2003
YOUR 307 CC IN DETAIL97
BOOT Opening the boot 
Press and hold button Bon the
remote control to partially open the boot, or press button Con the
boot.Locking/Unlocking from the inside Pressing button Apermits:
Ð locking of the vehicle,
Ð unlocking of the vehicle (and in particular the boot) if you place the key in the switch.
"Door open" or "boot open" warnings When the engine is running, if a door
or the boot is not closed correctly,you are warned by an audible signaland a diagram on the multifunctiondisplay for a few seconds. In addition, when the vehicle is mov- ing, the courtesy lights flash.To protect the boot against theft, but- ton Ccan be disarmed. Turn the lock
D a quarter of a turn to the right using
the key. The boot can only be opened using the remote control. The boot locks automatically when the vehicle is being driven at 6 mph(10 km/h). It unlocks when one of thedoors is opened, if the speed is
below 6 mph (10 km/h) and the keyis in the ignition. Closing the boot  Use the interior grab handles to close the boot.
 Press the centre of the boot withboth hands until it locks.

22-09-2003
YOUR 307 CC IN DETAIL97
BOOT Opening the boot 
Press and hold button Bon the
remote control to partially open the boot, or press button Con the
boot.Locking/Unlocking from the inside Pressing button Apermits:
Ð locking of the vehicle,
Ð unlocking of the vehicle (and in particular the boot) if you place the key in the switch.
"Door open" or "boot open" warnings When the engine is running, if a door
or the boot is not closed correctly,you are warned by an audible signaland a diagram on the multifunctiondisplay for a few seconds. In addition, when the vehicle is mov- ing, the courtesy lights flash.To protect the boot against theft, but- ton Ccan be disarmed. Turn the lock
D a quarter of a turn to the right using
the key. The boot can only be opened using the remote control. The boot locks automatically when the vehicle is being driven at 6 mph(10 km/h). It unlocks when one of thedoors is opened, if the speed is
below 6 mph (10 km/h) and the keyis in the ignition. Closing the boot  Use the interior grab handles to close the boot.
 Press the centre of the boot withboth hands until it locks.

22-09-2003
YOUR 307 CC IN DETAIL99
OPENING THE BONNET From inside:
push the handle on the
left-hand side under the fascia. From outside: lift the catch and
raise the bonnet. Bonnet strut Secure the strut to hold the bonnet open. Before closing the bonnet, replace the strut in its housing.
To close Lower the bonnet and release it at the end of its travel. Check that thebonnet is properly locked. "Bonnet open" warning With the engine running or the vehi- cle moving, flashing of the central
"STOP"
warning light accompanied
by an audible signal and a diagram
on the multi-function display, warnsyou that the bonnet is not properlyclosed. FILLING WITH FUEL Low fuel level
When the minimum fuel level in the tank isreached, this warninglight comes on.
You can still drive approximately30 miles (50 km). Flashing of the warning light indi-cates a malfunction of the fuelgauge.
Contact a PEUGEOT dealer. The engine must be switched off when filling with fuel. 
Open the fuel filler flap.
 Insert the key then turn it to the left.
 Remove the cap and hang it onthe hook located on the inside ofthe flap.
A label affixed to the inside of the fuelfiller flap indicates which type of fuelto use. When you fill your tank, do not con-
tinue after the third cut-off of the
pump. This could cause your vehicleto malfunction. The capacity of the tank is approxi- mately 60 litres.  After filling the tank, lock the cap and close the fuel filler flap.

22-09-2003
YOUR 307 CC IN DETAIL
106
Colour screen DT
Ð the
"Current information" with:
¥ the range,
¥ the current consumption,
¥ the distance still to be driven.
Ð "Route 1" with:
¥ the distance travelled,
¥ the average consumption,
¥ the average speed,
Ð "Route 2" with the same features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-setWhen the required route is dis- played, press the button for morethan two seconds.
TRIP COMPUTER
Each time the button on the end of the wiper stalk
is pressed, the following
sequence of data is displayed:
Monochrome screen CT
Ð the "vehicle" tab with:
¥ range, current consumption and the distance still to be driven,
Ð tab "1'(route "1") with:
¥ the distance driven, the average consumption and the average speed calculated over route "1"
Ð tab "2"(route "2") with the same
features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-set When the required route is dis- played, press the button for morethan two seconds.
Monochrome screen B
Ð the remaining range
Ð the distance travelled
Ð the average consumption
Ð the current consumption
Ð the average speed In addition, it allows access to the warning log
information and to the
Excess speed warning* function.
Zero reset Press the stalk for more than two seconds.
* During the year.

22-09-2003
YOUR 307 CC IN DETAIL107
Distance remaining to be travelled This is the distance remaining to the destination. It can either be calculat-ed by the navigation if guidance is
activated, or entered by the user,minus the distance covered since thedistance was entered. Note:
if digits are missing, dashes
are displayed in their place.
Average speed This is the average speed calculated since the computer was last set tozero (with the ignition on). The warning log This summarises the active warning messages by displaying them on the
multi-function display. The excess speed warning function* This monitors the maximum speed required. In the event that the pro-grammed speed is exceeded, themessage ''Speed too high'' appears
on the multi-function display, accom-panied by an audible signal. Activation Keep pressing the control until the display indicates "Excess speed
ON" .
* During the year.
Range This shows the distance that can still be covered with the fuel remaining inthe tank. Note:
this figure may increase if
there is a change in the style of dri- ving or the road surface, producing asignificant drop in current consump-tion. If horizontal segments are displayed for long periods instead of digits,
contact a PEUGEOT dealer. Current consumption This is the average quantity of fuel consumed during the last few se-conds. This function is displayed only when the vehicle is travelling at a speedgreater than 20 mph (30 km/h).
Average consumption This is the average fuel consumption since the computer was last set tozero. Distance travelled This indicates the distance travelled since the computer was last set tozero. Programming
Press the control briefly. Accelerate to the desired speed.Keep pressing the control to store in
memory. Switching off Keep pressing the control until the display indicates
"Excess speed
OFF" .
The routes The routes "1"and "2"are indepen-
dent but have identical application.Route "1" for example allows you to
make daily calculations and route "2" monthly calculations.

22-09-2003
YOUR 307 CC IN DETAIL
106
Colour screen DT
Ð the
"Current information" with:
¥ the range,
¥ the current consumption,
¥ the distance still to be driven.
Ð "Route 1" with:
¥ the distance travelled,
¥ the average consumption,
¥ the average speed,
Ð "Route 2" with the same features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-setWhen the required route is dis- played, press the button for morethan two seconds.
TRIP COMPUTER
Each time the button on the end of the wiper stalk
is pressed, the following
sequence of data is displayed:
Monochrome screen CT
Ð the "vehicle" tab with:
¥ range, current consumption and the distance still to be driven,
Ð tab "1'(route "1") with:
¥ the distance driven, the average consumption and the average speed calculated over route "1"
Ð tab "2"(route "2") with the same
features.
It also permits access to the warn-
ing log information and to the
Excess Speed Warning* function.
Zero re-set When the required route is dis- played, press the button for morethan two seconds.
Monochrome screen B
Ð the remaining range
Ð the distance travelled
Ð the average consumption
Ð the current consumption
Ð the average speed In addition, it allows access to the warning log
information and to the
Excess speed warning* function.
Zero reset Press the stalk for more than two seconds.
* During the year.

22-09-2003
YOUR 307 CC IN DETAIL107
Distance remaining to be travelled This is the distance remaining to the destination. It can either be calculat-ed by the navigation if guidance is
activated, or entered by the user,minus the distance covered since thedistance was entered. Note:
if digits are missing, dashes
are displayed in their place.
Average speed This is the average speed calculated since the computer was last set tozero (with the ignition on). The warning log This summarises the active warning messages by displaying them on the
multi-function display. The excess speed warning function* This monitors the maximum speed required. In the event that the pro-grammed speed is exceeded, themessage ''Speed too high'' appears
on the multi-function display, accom-panied by an audible signal. Activation Keep pressing the control until the display indicates "Excess speed
ON" .
* During the year.
Range This shows the distance that can still be covered with the fuel remaining inthe tank. Note:
this figure may increase if
there is a change in the style of dri- ving or the road surface, producing asignificant drop in current consump-tion. If horizontal segments are displayed for long periods instead of digits,
contact a PEUGEOT dealer. Current consumption This is the average quantity of fuel consumed during the last few se-conds. This function is displayed only when the vehicle is travelling at a speedgreater than 20 mph (30 km/h).
Average consumption This is the average fuel consumption since the computer was last set tozero. Distance travelled This indicates the distance travelled since the computer was last set tozero. Programming
Press the control briefly. Accelerate to the desired speed.Keep pressing the control to store in
memory. Switching off Keep pressing the control until the display indicates
"Excess speed
OFF" .
The routes The routes "1"and "2"are indepen-
dent but have identical application.Route "1" for example allows you to
make daily calculations and route "2" monthly calculations.