2003 Peugeot 206 SW Owner's Manual

26-05-2003
INSTRUMENTS AND CONTROLS33
Seat belt not fastened warning light*
When the ignition is switched on, thisindicator light comes on if the driverhas not fastened his seat belt.
Front and side airbags warning light
The light will come on for a few secondswhen the ignition is switched on. With the engine running, illumination of this warning light is accompaniedby an audible signal and a messageon the multifunction display indicat-ing a fault in the air bags.
Consult a PEUGEOT dealer.
Battery charge warning light
This indicates one of the following:
Ð faulty operation of the charging circuit,
Ð slack battery or starter terminals,
Ð a cut or slack alternator belt,
Ð an alternator failure.
Consult a PEUGEOT dealer. Engine diagnostics warning light
This comes on each time the ignitionis switched on. If it comes on with the engine running, this indicates incorrect operation ofthe injection, ignition or emission con-
trol system. There is a risk of damageto the catalytic converter (petrolengine only).
Consult a PEUGEOT dealer.
Dynamic stability control system(ESP/ASR) warning light
This comes on for a few secondseach time the ignition is switched on.
Consult a PEUGEOT dealer if the ESP/ASR switch indicator light flash-es and this warning light remains onor comes on with the engine running,vehicle moving. With the engine running and the vehi- cle moving, it flashes if the system isactivated. It lights permanently when the system is disarmed.
* According to destination.
Water in diesel filter indicator*
Consult a PEUGEOT dealer as soonas possible. There is a risk of damage to the injection system. Passenger air bag disarming warninglight*
Illumination of this warning light is
accompanied by an audible signaland the message "Passenger air
bag deactivated" on the multifunction
display. If the passenger air bag is disarmed, the warning light comes on when the igni-tion is switched on and it remains on.
Always consult a PEUGEOT dealer if the warning light flashes.
Low fuel level warning light
When this light first comes on, you have enough fuel to drive at least 30 miles
(50 km). The tank capacity is approxi-
mately 50 litres. Diesel engine pre-heat warning light
Wait until the warning light goes out before starting the engine. If the temperature is high enough, the warning light comes on for less
than one second. You can start theengine without waiting.

26-05-2003
INSTRUMENTS AND CONTROLS
34
Engine oil temperature indicator With the engine running, this indicates the oil temperature:
Ð needle in zone (C), the temperature
is correct,
Ð needle in zone (D), the temperature
is too high. To lower the oil tempera- ture, reduce your speed.
Coolant temperature indicator
Ð needle in zone (A), the temperature
is correct,
Ð needle in zone (B), the temperature
is too high. The central STOP
warning light flashes.
You must stop.
Consult a PEUGEOT dealer.

26-05-2003
Instrument panel display After switching on the ignition, three functions are shown in succession:
Ð service indicator (see corresponding section),
Ð engine oil level indicator,
Ð total distance recorder (total or trip distances).Note:the total or trip distances are displayed for 30 seconds when the ignition is switched off, on opening the driver's door,
as well as on locking and unlocking the vehicle. Engine oil level When the ignition is switched on, the engine oil level is indicated for approximately 10 seconds, after the servicing informati on.
Maximum oil level If the flashing of the six squares is confirmed by checking using the dipstick, a surplus of oil can cause damage to the engine.
Consult a PEUGEOT dealer without delay. Lack of oilFlashing of the six segments and "min" on the display indicate a lack of oil which can cause damage to the engine. If the lack of oil is confirmed by checking using the dipstick, it is essential to top up the level.
Oil level gauge fault Flashing of the six segments indicates a fault in the oil level gauge.There is a risk the engine will be damaged.
Consult a PEUGEOT dealer.
INSTRUMENTS AND CONTROLS 35
The level indicated when checking using the dipstick is only correct if the vehicle has been on level ground, with the engine stopped, for more than 10 minutes.

26-05-2003
INSTRUMENTS AND CONTROLS
36
Total distance records Briefly pressing button
1alternates
between the total and trip distance displays.
To reset the trip recorder to zero, when it is displayed press the buttonfor more than 3 seconds. HAZARD WARNING LIGHTS
Press the button, the direction indica- tors flash.
They can operate with the ignition off. Automatic lighting of hazard warning lights*
When braking in an emergency, depending on the force of decelera-tion, the hazard warning lights come
on automatically. They switch off auto-matically the first time you accelerate.
It is also possible to switch them off by pressing the button.
* According to destination.
Lighting rheostat With the lights on, press the button to vary the intensity of the lighting ofthe instruments and controls. Whenthe lighting reaches the minimum (ormaximum) setting, release the but-ton then press it again to increase(or reduce) the brightness. As soon as the lighting is of the required brightness, release thebutton.

26-05-2003
YOUR 206 IN DETAIL37
DISPLAY A This displays the following information:
Ð the time,
Ð the date,
Ð the outside temperature (this
flashes if there is a risk of ice),
Ð the audio system displays,
Ð a door check (e.g.: ''left front door open''),
Ð warning messages (e.g. ''remote control battery flat'') or information messages (e.g. ''economy mode
active''), displayed temporarily. Adjusting the parameters Press and hold button
1for two seconds to access the settings; the data
flashes, indicating it is ready to be modified. Then, each press of button 1scrolls through the various data in the following
order:
Ð language of information displayed,
Ð hours (12 then 24 hour mode),
Ð minutes,
Ð year,
Ð month,
Ð day,
Ð unit of temperature (degrees Celsius or Fahrenheit).Pressing button 2alters the value of the parameter selected. Press and hold for
rapid advance (return to start after the last possible value). After 7 seconds with no action, the main display returns; the modified data are now recorded. Note: Pressing button 2briefly displays the outside temperature for a few
seconds.

26-05-2003
YOUR 206 IN DETAIL
38
Setting the parameters Press and hold button 1for two seconds to access the settings. The data
flashes, indicating it is ready to be modified. Then, individual presses on button 1allow you to scroll through the various data
in the following sequence:
Ð language in which the information is displayed,
Ð unit of distance (kms or miles),
Ð unit of temperature (degrees Celsius or Fahrenheit),
Ð time format (12 then 24 hour mode),
Ð hour,
Ð minutes,
Ð year,
Ð month,
Ð day.Pressing button 2allows you to change the data selected. Maintain the pressure
for rapid scrolling.After 7 seconds without moving, the main display returns; the modified data are now recorded.
DISPLAY B This enables the following informa- tion to be displayed:
Ð the time,
Ð the date,
Ð the outside temperature (this flashes when there is a risk of ice),
Ð the radio displays,
Ð the status of the doors. The dis- play shows you, by means of a graphic, whether a door is open,
Ð the warning messages (e.g. ''bat- tery charge low'') or informationmessages (e.g. "fuel tank low''),
displayed temporarily, can becleared by pressing button 1or 2,
Ð the trip computer.

26-05-2003
YOUR 206 IN DETAIL39
DISPLAY C This enables the following informa- tion to be displayed:
Ð the time,
Ð the date,
Ð the outside temperature (this flashes when there is a risk of ice),
Ð the radio displays,
Ð the status of the doors. The dis- play shows you, by means of a graphic, whether a door is open, Ð the warning messages (e.g. "fuel level low''), displayed temporarily. These can
be cleared using the remote control,
Ð the trip computer (see corresponding section),
Ð the satellite navigation system (see corresponding section). Setting the parameters
The remote control allows you to access the settings. Accessing the different menus is described in the section ''Satellite Navigation System''.

26-05-2003
AUDIO RB3
YOUR 206 IN DETAIL
42
Stalk movement
Function
1- Press (behind) Increase volume
2- Press (behind) Decrease volume
1 + 2 - Simultaneous press Sound cut-off (mute); restoring of the sound by pressing any button
3- Press Automatic search of higher frequencies (radio) -
Selection of the next track (CD)
4- Press Automatic search of lower frequencies (radio) -
Selection of the previous track (CD)
5- Press the end Change of source (radio/cassette/CD changer)
6- Rotation Selection of next station stored in memory (radio) -
(clockwise) Selection of next CD
7- Rotation Selection of previous station stored in memory (radio) -
(anti-clockwise) Selection of previous CD