
When an  air  baa  jnflates,  there is dust  in  the 
air.  This  dust  could  cause  breathing  problems 
for  people  with  a  history  of  asthma  or  other  breathing  trouble. 
To avoid this, everyone in 
the  vehicle  should  get  out  as  soon  as it is safe 
to  do 
so. If  you  have breathing  problems but 
can’t  get  out  of  the  vehicle  after  an  air  bag 
inflates,  then  get  fresh  air  by  opening  a 
window  or  a  door. 
If you  experience  breathing 
problems  following  an  air  bag  deployment, 
you  should  seek medical  attention. 
In  many  crashes  severe  enough to inflate an  air  bag, 
windshields  are  broken  by  vehicle deformation. 
Additional  windshield  breakage  may  also occur from 
the  right  front  passenger  air  bag. 
Air  bags  are designed to  inflate only once. After  an 
air  bag  inflates,  you’ll  need some  new  parts for 
your  air  bag  system.  If  you don’t  get them,  the air 
bag  system  won’t  be  there to help protect you 
in  another  crash. 
A new  system  will include air  bag 
manual  for  your  vehicle  covers the  need to replace 
other  parts. 
modules and possibly other parts. The service 
Your vehicle is equipped  with an electronic frontal 
sensor,  which helps the sensing system distinguish 
between  a moderate frontal impact and  a more 
severe  frontal  impact.  Your vehicle  is also equipped 
with  a  crash sensing and diagnostic module, 
which  records information about the frontal air  bag 
system.  The  module records information about 
the  readiness  of the system,  when the system 
commands  air bag inflation and driver’s safety belt 
usage  at deployment. The  module 
also records 
speed,  engine 
RPM, brake and throttle  data. 
Let only qualified technicians  work on your air  bag 
systems.  Improper service can  mean  that an air 
bag system  won’t  work properly. See your dealer 
for  service. 
Notice: If you  damage  the  covering  for  the  driver’s 
or the  right  front  passenger’s  air  bag, or  the  air 
bag  covering  on  the  driver’s  and  right  front 
passenger’s  seatback,  the  bag  may  not  work 
properly.  You  may  have  to replace  the  air  bag 
module 
in the  steering  wheel,  both  the  air  bag 
module  and  the  instrument  panel  for  the  right  front 
passenger’s  air  bag,  or  both  the  air  bag  module 
and  seatback  for  the  driver’s  and  right  front 
passenger’s  side  impact  air  bag. 
Do not  open  or 
break  the  air  bag  coverings. 
1 -75  

REVERSE (R): Use this gear to  back  up. 
Notice: Shifting to REVERSE (R) while  your  vehicle 
is  moving  forward  could  damage  your  transaxle. 
Shift  to REVERSE 
(R) only  after  your  vehicle 
is  stopped. 
To rock  your  vehicle  back  and forth to get out  of snow, 
ice  or sand  without  damaging your  transaxle,  see 
If You Are  Stuck: In Sand, Mud, Ice  or Snow on 
page 4-30. 
NEUTRAL  (N):  In this position, your  engine  doesn’t 
connect  with  the  wheels.  To restart  when  you’re  already 
moving,  use  NEUTRAL 
(N) only.  Also,  use  NEUTRAL (N) 
when  your  vehicle  is being towed. 
Shifting  into  a  drive  gear while  your  engine 
Unless  your  foot 
is firmly  on  the  brake  pedal, 
your  vehicle  could  move  very  rapidly.  You 
could  lose  control  and 
hit people  or  objects. 
Don’t  shift  into  a  drive  gear while  your  engine 
is  racing. 
“rqcjng” (running 3t high speed) i$ dangP?rQl!s 
Notice: Damage  to  your  transaxle  caused  by 
shifting  into  a  drive  gear  with  the  engine  racing 
isn’t  covered  by  your  warranty. 
AUTOMATIC  OVERDRIVE  (D): This position is for 
normal driving.  If you  need more power for  passing, 
and  you’re: 
Going less than 35 mph (55 km/h),  push your 
Going about 35 mph (55 km/h)  or  more, push  the 
You’ll shift down to the  next gear  and  have more power. 
Notice; If  your  vehicle  seems  to  start  up  rather 
slowly,  or  if 
it seems  not  to  shift  gears  as  you  go 
faster,  something  may  be  wrong  with  a  transaxle 
system  sensor.  If  you  drive  very  far  that  way, 
your  vehicle  can  be  damaged. 
So, if this happens, 
.lave  your  vehicle  serviced  right  away. Until  then, 
you  can  use  SECOND 
(2) when  you  are  driving 
less  than 
35 mph (55 km/h)  and  AUTOMATIC 
accelerator pedal 
about halfway down. 
accelerator all the way down. n\~nnn~
= In s-” L:-L-” -.......A. w v LnurlI Y L \YI tui 1 utyt IC# apr;r?wa. 
2-37  

Warm-up Shift 
Your vehicle has a computer controlled transaxle 
designed  to warm  up the engine  faster  when the  outside 
temperature  is 
35°F (2°C) or colder.  You  may notice 
that  the transaxle will shift at a higher vehicle speed until 
the engine is warmed  up. This  is a  normal condition 
designed  to provide heat  to the  passenger compartment 
and defrost the  windows more quickly.  See 
Climate 
Control  System  on 
page 3-25 for more information. 
THIRD 
(3): This  position  is also used for  normal driving, 
but  it  offers  more power and lower fuel  economy than 
AUTOMATIC  OVERDRIVE (D). 
Here are  some times you  might choose THIRD 
(3) 
instead  of AUTOMATIC  OVERDRIVE (D): 
When driving on hilly, winding  roads. 
When towing a trailer (so there is less shifting 
When going down a steep hill. between gears). 
SECOND 
(2): This  position gives  you more power, 
but lower fuel economy.  You can  use SECOND 
(2) on 
hills. It can help control  your speed as you  go down 
steep mountain roads,  but then you would also want to 
use your  brakes 
off and  on. 
Notice: Don’t  drive  in  SECOND (2) for  more  than 
25 miles (40 km), or at speeds  over 55 mph (90 km/h), 
or  you  can  damage  your  transaxle.  Use  THIRD 
(3) or 
AUTOMATIC  OVERDRIVE (D) as much  as possible. 
Don’t 
shift into  SECOND (2) unless  you  are  going 
slower  than 
65 mph (105 km/h)  or  you  can  damage 
your  engine. 
Notice: If your  vehicle  seems to start up  rather 
slowly,  or  if 
it seems  not  to  shift gears as you  go 
faster,  something  may  be  wrong  with  a  transaxle 
system  sensor.  If  you  drive  very  far  that  way, your 
vehicle  can  be  damaged. 
So, if  this happens,  have 
your  vehicle  serviced 
right away.  Until then,  you can 
use  SECOND 
(2) when  you  are driving  less  than 
35 mph (55 km/h)  and  THIRD (3) for  higher speeds. 
FIRST 
(1): This position  gives  you  even  more  power 
(but  lower  fuel economy)  than 
SECOND (2). You  can  use 
it  on  very  steep  hills, or in deep  snow  or  mud. 
If the  shift 
lever is  put in FIRST 
(I), the transaxle  won’t downshift 
into  first  gear  until the vehicle is going  slow  enough. 
Notice: If  your  front  wheels  won’t  turn, don’t  try  to 
drive.  This  might  happen  if  you  were stuck  in  very 
deep  sand  or  mud  or  were up  against  a  solid  object. 
You could  damage  your  transaxle.  Also, if  you  stop 
when  going 
uphill, don’t  hold  your  vehicle  there  with 
only  the  accelerator  pedal. This  could  overheat  and 
damage  the  transaxle.  Use  your  brakes  to  hold  your 
vehicle  in  position  on  a 
hill. 
2-38  

Daytime Running Lamps/Automatic 
Headlamp  System 
Daytime  Running  Lamps  (DRL) can make it easier for 
others  to  see  the front  of your vehicle during the 
day.  DRL  can be helpful  in many different driving 
conditions,  but  they  can be especially helpful 
in the short 
periods  after  dawn  and before sunset.  Fully functional 
daytime  running  lamps  are  required on all vehicles 
first  sold  in  Canada. 
A light  sensor  on  top of the  instrument panel makes 
the 
DRL work, so be  sure  it isn’t covered.  The DRL 
system  will  make  your  front  parking and turn signal 
lamps  come  on in daylight  when: 
The ignition is  on, 
the  exterior  lamps  control is off,  and 
the  parking  brake  is  released. 
When  the DRL  are  on,  only  your front parking and turn 
signal  lamps  will  be on.  Your  instrument panel  won’t 
Le I:+ . .- ue 111 up. 
When it’s  dark  enough outside,  the exterior lamps  will 
come on automatically. When  it’s bright enough outside, 
the exterior lamps  will turn 
off and the  DRL will turn 
on.  Of  course, you  may still turn on the  headlamps  any 
time you  need  to. 
If you start your vehicle in  a dark  garage,  the automatic 
headlamp system will come on immediately. Once 
you  leave the  garage, it will take  approximately 
one minute for the automatic headlamp system to 
change to  DRL 
if it is  light  outside.  During that  delay, 
your  instrument panel cluster  may not be  as bright 
as  usual.  Make sure  your  instrument panel brightness 
control  is  in the full  bright position. See “Instrument 
Panel Brightness  Control’’ under 
lnterior Lamps 
on  page 
3-17. 
To idle your vehicle  with the DRL  and automatic 
headlamp control 
off, set  the  parking brake while the 
ignition  is in OFF  or  LOCK.  Then start the vehicle. 
The  DRL  and automatic  headlamp control will  stay 
off 
until you  release the  parking brake. 
As with any vehicle.  you  should turn on the  reuular 
headlamp system  when you  need 
it. 
3-1 5  

How the System Works 
Unless  disabled,  the  URPA  will turn on automatically 
when  the shift lever is  moved into REVERSE  (R). 
When  the system  turns  on,  the three  lights on  the 
display  will  illuminate for  one  and  a  half  seconds  to let 
you  know  that  the system  is working.  If your vehicle 
is  moving  in REVERSE  (R)  at a  speed  greater 
than 
3 mph (5 km/h),  the  red light will flash to  remind 
you  that  the system  does  not work  at speed  greater than 
3 mph (5 km/h). 
If  an  object  is detected  at a REVERSE  (R)  speed  of 
less than 
3 mph (5 km/h),  one  of the following will occur: 
Description 
1.5 m 5 ft. 
amber  light  Metric 
English I - I 
ambedamber  lights 
0.5  m 
continuous  chime 1.0 m 40 in. 
ambedambedred  lights 
& 20 in. 
1 ambedambedred lights 
chime I I 
A  chime will sound  the  first  time an object is detected 
between 
20 inches (0.5 m)  and  5 feet (1.5 m)  away. 
flashing 
& continuous I 0.3 m 
L 
When 
the  System Does Not Seem to 
Work  Properly 
The  light  may flash  red  when  the  vehicle is in 
REVERSE  (R) if the ultrasonic sensors are  not kept 
clean. 
So be  sure  to keep  your rear  bumper  free of mud, 
dirt,  snow,  ice and slush.  Other conditions that  may 
affect  system  performance  include things like  the 
vibrations from  a  jackhammer  or  the compression  of 
air brakes  on a very  large truck.  If after cleaning 
the  rear  bumper and then  driving forward  at least 
15  mph 
(25 km/h),  the display continues to flash  red, 
see  your dealer. 
If  a  trailer  was attached  to your  vehicle,  or  a bicycle or 
an  object  was  on  the back  of,  or hanging  out of your 
liftgate during your  last drive cycle,  the light  may 
also flash  red.  The light will continue  to flash  whenever 
in  REVERSE  (R)  until your vehicle  is driven forward 
at least  15 mph  (25 km/h)  without  any  obstructions 
behind  the vehicle. 
For  cleaning instructions,  see 
Cleaning the Outside of .I- I#-#-. I UUI vellrdc oli p/ayt. a-rv. r 
URPA cannot  detect objects that are  above liftgate level. 
In order  for  the  rear  sensors to  recognize  an object, 
it  must  be  within detection  range behind  the vehicle. 
3-23  

I Fuse I Usage I 
Blank I Not Used 
I PCM/CRANK I Powertrain  Control  Module (PCM), 
Ignition Crank 
I PASS  KEY I PASS-Key@ Ill System I 
I PWR  LOCK I Power  Door  Locks I 
I HTD MIRROR I Heated  Mirrors I 
I 
RH  T/LP I Driver’s  Side  Taillamp (Export  Only) I 
I 
RR FOG LP I Fog  Lamps  (Export  Only) I 
CIGAR/DIC/ 
Auxiliary Power Outlets,  Data Link 
APO  FRT  Cigarette 
Lighter,  DIC,  Front 
I T/SIG I Turn Signal  Switch I 
PWR  QTR 
VENT  Interior  Lamp 
and Multifunction 
Switch  (Power  Vent  Switch), 
Auto  Level 
Windshield  WiperNVasher  Motor 
and  Switch 
I HAZARD I Hazard  Switch I 
I RR  PWR  SCKT I Rear  Electric  Accessory  Plug 
Housing 
I DRL  Daytime  Running 
Lamp Control 
Module  Fuse 
I Usage 
LH T/LP 
I 
Passenger’s  Side  Taillamp 
(Export  Only) 
RR DEFOG/  Rear  Window  Defogger  Relay, 
HTD  MIRROR  Heated  Mirrors 
ON STAR onstar@ 
SIR  Inflatable  Restraint  Control  Module  HVAC 
I Heater-A/C  Control 
BLOWER 
MALL 
CLUSTER  Instrument  Cluster,  Body  Control 
Module,  Electronic  Level  Control 
(ELC)  Sensor  and  Relay,  Theft, 
Door  Ajar 
STOP  LAMP 
I Stoplamp  Switch 
CLUSTER  BATT  Module/Electronic  Brake  Control 
Module/Electronic  Brake  Traction 
Control  Module  (EBCM/EBTCM) 
Evaporative  Emissions  (EVAP) 
Canister  Vent  Solenoid  Valve, 
All-Wheel  Drive  (AWD) 
ENHANCED 
Blank  Not  Used 
ELC  Air  Compressor  and  ELC 
Heiaht  Sensor.  Trailer  Harness 
5-98