2003 NISSAN X-TRAIL lock

LT-20
HEADLAMP - DAYTIME LIGHT SYSTEM -

HEADLAMP - DAYTIME LIGHT SYSTEM -PFP:26010
System DescriptionEKS003BB
DESCRIPTION
The headlamp system on vehicles for North Europe contains a daytime light control unit. The unit activates the
following whenever the engine is running with the lighting switch in the OFF position:

Low beam headlamps

Parking, license, tail and illumination lamps
Power is supplied at all times

through 10A fuse (No. 31, located in the fuse and fusible link box)

to daytime light control unit terminal 1 and

to lighting switch terminal 11.
Power is also supplied at all times

through 15A fuse (No. 41, located in the fuse and fusible link box)

to daytime light control unit terminal 3 and

to lighting switch terminal 5.
Power is also supplied at all times

through 15A fuse (No. 40, located in the fuse and fusible link box)

to daytime light control unit terminal 2 and

to lighting switch terminal 8.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 13, located in the fuse block (J/B)]

to daytime light control unit terminal 7.
With the ignition switch in the START position, power is supplied

through 10A fuse [No. 7, located in the fuse block (J/B)]

to daytime light control unit terminal 6.
HEADLAMP OPERATION (DAYTIME LIGHT CANCEL OPERATION)
When the lighting switch is turned to the 1st or 2nd position, power is supplied

through lighting switch terminal 12

to daytime light control unit terminal 11.
Then daytime light will be canceled. And the lighting system operation will be the same as no daytime light
system.
DAYTIME LIGHT OPERATION
With the engine running and the lighting switch in the OFF position, power is supplied

from alternator terminal 3

to daytime light control unit terminal 8,

through daytime light control unit terminal 5

to terminal 3 of headlamp LH,

through daytime light control unit terminal 4

to terminal 3 of headlamp RH and

through daytime light control unit terminal 10

to tail lamp and illumination.
Ground is supplied to terminal 2 of each headlamp through body grounds E24 and E50.
DRIVING LAMP OPERATION
To turn the driving lamp on, push the driving lamp switch when the lighting switch is turned to the 2ND position
and placed in HIGH position or PASS position, power is supplied

from lighting switch terminal 9

to headlamp LH terminal 1

to driving lamp relay-1 terminal 1

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-31
C
D
E
F
G
H
I
J
L
MA
B
LT

TURN SIGNAL AND HAZARD WARNING LAMPSPFP:26120
System Description EKS003BX
TURN SIGNAL OPERATION
With the hazard switch in the OFF position and the ignition switch in the ON or START position, power is sup-
plied

through 10A fuse [No. 2, located in the fuse block (J/B)]

to hazard switch terminal 2

through hazard switch terminal 1

to combination flasher unit terminal 1

through combination flasher unit terminal 3

to turn signal switch terminal 1.
Ground is supplied

to combination flasher unit terminal 2 through grounds M27 and M70.
LH Turn
When the turn signal switch is moved to the LH position, power is supplied from turn signal switch terminal 3

to front turn signal lamp LH terminal 1

to side turn signal lamp LH terminal 1

to combination meter terminal 52

to rear combination lamp LH terminal 2.
Ground is supplied

to the front turn signal lamp LH terminal 2 through grounds E24 and E50

to the side turn signal lamp LH terminal 2 through grounds E24 and E50

to the rear combination lamp LH terminal 4 through grounds B8 and B18

to combination meter terminal 64 through grounds M27 and M70.
With power and ground supplied, the combination flasher unit controls the flashing of the LH turn signal lamps.
RH Turn
When the turn signal switch is moved to the RH position, power is supplied from turn signal switch terminal 2

to front turn signal lamp RH terminal 1

to side turn signal lamp RH terminal 1

to combination meter terminal 18

to rear combination lamp RH terminal 2.
Ground is supplied

to the front turn signal lamp RH terminal 2 through grounds E24 and E50

to the side turn signal lamp RH terminal 2 through grounds E24 and E50

to the rear combination lamp RH terminal 4 through grounds B8 and B18

to combination meter terminal 64 through grounds M27 and M70.
With power and ground supplied, the combination flasher unit controls the flashing of the RH turn signal
lamps.
HAZARD LAMP OPERATION
Power is supplied at all times to hazard switch terminal 3

through 10A fuse (No. 35, located in the fuse and fusible link box).
With the hazard switch in the ON position, power is supplied

through hazard switch terminal 1

to combination flasher unit terminal 1

through combination flasher unit terminal 3

to hazard switch terminal 4.
Ground is supplied

to combination flasher unit terminal 2 through grounds M27 and M70.

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-37
C
D
E
F
G
H
I
J
L
MA
B
LT

Trouble Diagnoses EKS003BG
Electrical Components InspectionEKS0034C
COMBINATION FLASHER UNIT CHECK

Before checking, ensure that bulbs meet specifications.

Connect a battery and test lamp to the combination flasher unit,
as shown. Combination flasher unit is properly functioning if it
blinks when power is supplied to the circuit.
Symptom Possible cause Repair order
Turn signal and hazard warning lamps do
not operate.1. Hazard switch
2. Combination flasher unit
3. Open in combination flasher unit circuit1. Check hazard switch.
2. Refer to combination flasher unit check.
3. Check wiring to combination flasher unit
for open circuit.
Turn signal lamps do not operate but haz-
ard warning lamps operate.1. 10A fuse
2. Hazard switch
3. Turn signal switch
4. Open in turn signal switch circuit1. Check 10A fuse [No. 2, located in fuse
block (J/B)]. Turn ignition switch ON and
verify battery positive voltage is present
at terminal 2 of hazard switch.
2. Check hazard switch.
3. Check turn signal switch.
4. Check the wire between combination
flasher unit terminal 3 and turn signal
switch terminal 1 for open circuit.
Hazard warning lamps do not operate but
turn signal lamps operate.1. 10A fuse
2. Hazard switch
3. Open in hazard switch circuit1. Check 10A fuse (No. 35, located in the
fuse and fusible link box). Verify battery
positive voltage is present at terminal 3
of hazard switch.
2. Check hazard switch.
3. Check the wire between combination
flasher unit terminal 3 and hazard switch
terminal 4 for open circuit.
Front turn signal lamp LH or RH does not
operate.1. Bulb
2. Grounds E24 and E501. Check bulb.
2. Check grounds E24 and E50.
Rear turn signal lamp LH or RH does not
operate.1. Bulb
2. Grounds B8 and B181. Check bulb.
2. Check grounds B8 and B18.
Side turn signal lamp LH or RH does not
operate.1. Bulb
2. Grounds E24 and E501. Check bulb.
2. Check grounds E24 and E50.
LH and RH turn indicators do not operate. 1. Ground 1. Check grounds M27 and M70.
LH or RH turn indicator does not operate. 1. Bulb 1. Check bulb in combination meter.
SEL122E

LT-38
TURN SIGNAL AND HAZARD WARNING LAMPS

Bulb ReplacementEKS0034D
FRONT TURN SIGNAL LAMP
1. Remove the front turn signal lamp. Refer toLT- 3 8 , "Removal and
Installation for Front Turn Signal Lamp"
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
SIDE TURN SIGNAL LAMP
1. Remove side turn signal lamp. Refer toLT- 3 8 , "Removal and
Installation for Side Turn Signal Lamp"
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
REAR TURN SIGNAL LAMP
Refer to LT- 6 3 , "Bulb Replacement" .
Removal and Installation for Front Turn Signal LampEKS003BH
REMOVAL
1. Press the upper pawl to remove front turn signal lamp toward
the front of the vehicle.
2. Disconnect front turn signal lamp connector.
INSTALLATION
1. Connect front turn signal lamp connector.
2. Insert the pawl into head lamp hole, and install front turn signal lamp.
Removal and Installation for Side Turn Signal LampEKS003BI
1. Push the side turn signal lamp toward A direction in the figure,
and pull up B direction in the figure.
2. Disconnect the side turn signal lamp connector.Front turn signal lamp : 12V 21W (amber)
SKIA0053E
Side turn signal lamp : 12V 5W
PKIA0468E
SKIA0054E
PKIA0469E

STOP LAMP
LT-43
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS0034K
STOP LAMP
Refer to LT- 6 3 , "Bulb Replacement" .
HIGH-MOUNTED STOP LAMP
1. Remove the high-mounted stop lamp cover. Refer to LT- 4 3 ,
"HIGH-MOUNTED STOP LAMP" .
2. Turn the high-mounted stop lamp bulb socket counterclockwise
and unlock it.
3. Remove the bulb.
Removal and InstallationEKS0034L
STOP LAMP
Refer toLT- 6 3 , "Removal and Installation" .
HIGH-MOUNTED STOP LAMP
1. Pull the edge of the cover (A in the figure below) to each side in
turn downward until the pawls inside the cover are released.
2. Pull down the cover toward under the vehicle.
3. Remove the high-mounted stop lamp mounting bolts.
4. Disconnect the high-mounted stop lamp connector and remove
it from the vehicle.High-mounted Stop Lamp : 12V 5W
PKIA0496E
PKIA8618E
PKIA5577E

FRONT FOG LAMP
LT-55
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb Replacement EKS003DI
1. Remove fog lamp. Refer to LT- 5 5 , "Removal and Installation" .
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
4. Install in the reverse order of removal.
CAUTION:

Do not touch the glass of bulb directly by hand. Keep
grease and other oily matters away from it. Do not touch
bulb by hand while it is lit or right after being turned off.
Burning may result.

Do not leave bulb out of fog lamp housing for a long time because dust, moisture smoke, etc. May
affect the performance of fog lamp. When replacing bulb, be sure to replace it with new one.
Removal and Installation EKS003DJ
REMOVAL
1. Remove fender protector. Refer to EI-21, "FENDER PROTECTOR" .
2. Disconnect fog lamp connector.
3. Remove fog lamp mounting nuts from fog lamp bracket.
4. Pull out fog lamp from vehicle and disconnect connector.
INSTALLATION

Install fog lamp in the reverse order of removal, observing the tightening torque shown below.Front fog lamp :12V 55W (H11)
PKIA5559E
PKIA5560E
Fog lamp mounting bolt
Tightening torque
: 5.5 N·m (0.56 kg-m, 49 in-lb)

REAR FOG LAMP
LT-59
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS0015L
1. Remove rear fog lamp. Refer to LT- 5 9 , "Removal and Installa-
tion" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
Removal and InstallationEKS0015M
REMOVAL
1. Remove rear fog lamp mounting screws (2).
2. Take out rear fog lamp from bumper, then disconnect connector.
INSTALLATION
Install in the reverse order of removal, paying attention to the following.Rear fog lamp : 12V 21W
SKIA0052E
SKIA0090E
Rear fog lamp mounting screws
Tightening torque : 1.4 N·m (0.14 kg-m, 12 in-lb)

REAR COMBINATION LAMP
LT-63
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS00164
1. Remove rear combination lamp mounting bolts (2).
2. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb.
Removal and InstallationEKS00165
REMOVAL
1. Remove luggage-side lower finisher. Refer to EI-35, "BODY
SIDE TRIM" in "EI EXTERIOR & INTERIOR" section.
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting bolts (2).
4. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
5. From outside the vehicle, pull harness grommet rearward, and
remove harness.
INSTALLATION
Install in the reverse order of removal, paying attention to the following.Stop/taillight : 12V 21/5W
Rear turn signal lamp : 12V 21W
Backup lamp : 12V 21W
SKIA0057E
PKIA8620E
Rear combination lamp mounting bolts
Tightening torque
: 5.4 N·m (0.55 kg-m, 48 in-lb)