2003 NISSAN X-TRAIL sunroof

MA-4
DESCRIPTION

DESCRIPTIONPFP:00000
Pre-delivery Inspection ItemsELS000Y5
Shown below are Pre-delivery Inspection Items required for the new vehicle. It is recommended that
necessary items other than those listed here be added, paying due regard to the conditions in each
country.
Perform applicable items on each model. Consult text of this section for specifications.
Install vehicle protection kit
Fit all accessories ordered (if applicable) (e.g. towbar, audio, navigation, air conditioner, styling kit)
UNDER HOOD — engine off
Check coolant level and cooling system for leaks
Charge battery and check terminals for condition
Check drive belts tension (diesel only)
Check fuel filter for water or dust (diesel only) and fuel system for leaks
Check engine oil level and for oil leaks
Check brake and clutch fluid levels and fluid lines for leaks
Check and top up washer reservoirs
Check power steering fluid level and fluid lines for leaks (if applicable)
Check air conditioning system for gas leaks (if applicable)
ON INSIDE AND OUTSIDE
Install transit fuse if removed for vehicle storage
Check instruments, gauges, lamps, horn and accessories for operation
Check wipers and washers for operation and adjustment
Check interior and door mirrors and sun visors for operation
Set radio code and set clock
Check parking brake adjustment
Check clutch pedal adjustment
Check steering lock operation
Check seat adjusters and seat belts for operation
Check all windows for operation and alignment
Check mouldings, trim and fittings for fit and alignment
Check weatherstrips for fit and adhesion
Check hood, trunk lid, door panels and fuel lid for fit and alignment
Check latches, keys, remote key, door locks and remote trunk lid and fuel lid release for operation
Check wheel nut torques
Check tyre pressure (incl. spare tyre)
Check tool kit and jack for operation
Check automatic transmission/transaxle starter inhibitor (if applicable)
Check sunroof for operation and alignment (if applicable)
UNDER BODY
Check manual transmission/transaxle, differential and transfer box for oil level and oil leaks
Tighten bolts and nuts steering linkage and gear box, axle/suspension parts, propeller and exhaust system
Check brake and clutch lines, and oil/fluid reservoirs for leaks
Remove front suspension spacer blocks (if applicable)
Check body mounting torque (if applicable)

CHASSIS AND BODY MAINTENANCE
MA-45
C
D
E
F
G
H
I
J
K
MA
B
MA

Drive ShaftELS000CL

Check boot and drive shaft for cracks, wear, damage and
grease leakage.
Lubricating Locks, Hinges and Hood LatchesELS000BR
Checking Seat Belts, Buckles, Retractors, Anchors and AdjustersELS000BS
Checking Body CorrosionELS000C0
Visually check body panels for collision damage (scratches, chipping, rubbing, etc.) or damage to the anti-cor-
rosion materials. In particular, check the following locations.
HEMMED PANELS
Hood front end, door lower end, trunk lid rear end, etc.
PA N E L J O I N T
Side sill of rear fender and center pillar, rear wheel housing of rear fender, around strut tower in engine com-
partment, etc.
PA N E L E D G E
Trunk lid opening, sunroof opening, fender wheel-arch flange, fuel filler lid flange, around holes in panel, etc.
PARTS CONTACT
Waist moulding, windshield moulding, bumper, etc.
SFA108A
Front door Refer to BL-18, "DOOR" .
Back door Refer to BL-99, "
BACK DOOR" .

HARNESS
PG-63
C
D
E
F
G
H
I
J
L
MA
B
PG

PGC/V EC EVAP Canister Purge Volume Control Solenoid Valve
PHASE EC Camshaft Position Sensor (PHASE)
PHONE AV Telephone (Pre-wire)
PNP/SW AT Park/Neutral Position Switch
PNP/SW EC Park/Neutral Position Switch
PNPSW1 EC Park/Neutral Position Switch
POS EC Crankshaft Position Sensor (CKPS) (POS)
POWER PG Power Supply Routing
PRGVLV EC EVAP Canister Purge Volume Control Solenoid Valve
PRWIRE BL Theft Warning System (Pre-wire)
PS/SEN EC Power Steering Pressure Sensor
PST/SW EC Power Steering Oil Pressure Switch
R/FOG LT Rear Fog Lamp
ROOM/L LT Interior Room Lamp
RP/SEN EC Refrigerant Pressure Sensor
RRO2 EC Rear Heated Oxygen Sensor
RRO2/H EC Rear Heated Oxygen Sensor Heater
S/LOCK BL Power Door Lock - Super Lock
S/SIG EC Start Signal
S/WARN SB Seat Belt Warning System
SEAT SE Power Seat
SEN/PW EC Sensor Power Supply
SHIFT AT A/T Shift Lock System
SROOF RF Sunroof
SRS SRS Supplemental Restraint System
SSV/A AT Shift Solenoid Valve A
SSV/B AT Shift Solenoid Valve B
START SC Starting System
STEP/L LT Step Lamp
STOP/L LT Stop Lamp
TAIL/L LT Parking, License and Tail Lamps
TCC/V EC Turbocharger Boost Control Solenoid Valve
TCCSV EC Turbocharger Boost Control Solenoid Valve
TCV AT Torque Converter Clutch Solenoid Valve
TPS AT Throttle Position Sensor
TPS1 EC Throttle Position Sensor (Sensor 1)
TPS2 EC Throttle Position Sensor (Sensor 2)
TPS3 EC Throttle Position Sensor
TURN LT Turn Signal and Hazard Warning Lamp
VIAS EC Variable Induction Air Control System
VSSA/T AT Vehicle Speed Sensor A/T (Revolution Sensor)
VSSMTR AT Vehicle Speed Sensor MTR
WARN DI Warning Lamps
WINDOW GW Power Window Code Section Wiring Diagram Name

LT-2 HAZARD SWITCH .................................................... 41
Removal and Installation ........................................ 41
REMOVAL ........................................................... 41
INSTALLATION .................................................... 41
STOP LAMP .............................................................. 42
Wiring Diagram — STOP/L — ................................ 42
Bulb Replacement .................................................. 43
STOP LAMP ........................................................ 43
HIGH-MOUNTED STOP LAMP ........................... 43
Removal and Installation ........................................ 43
STOP LAMP ........................................................ 43
HIGH-MOUNTED STOP LAMP ........................... 43
BACK-UP LAMP ....................................................... 44
Wiring Diagram — BACK/L — ................................ 44
GASOLINE ENGINE ........................................... 44
DIESEL ENGINE ................................................. 45
Bulb Replacement .................................................. 46
Removal and Installation ........................................ 46
PARKING, LICENSE PLATE AND TAIL LAMPS ...... 47
Wiring Diagram — TAIL/L — .................................. 47
LHD MODELS ..................................................... 47
RHD MODELS ..................................................... 49
Bulb Replacement .................................................. 51
PARKING AND TAIL LAMPS ............................... 51
LICENSE PLATE LAMP ...................................... 51
Removal and Installation ........................................ 51
PARKING AND TAIL LAMPS ............................... 51
LICENSE PLATE LAMP ...................................... 51
FRONT FOG LAMP .................................................. 52
System Description ................................................. 52
DESCRIPTION .................................................... 52
FOG LAMP OPERATION .................................... 52
Wiring Diagram — F/FOG — .................................. 53
Aiming Adjustment .................................................. 54
Bulb Replacement .................................................. 55
Removal and Installation ........................................ 55
REMOVAL ........................................................... 55
INSTALLATION .................................................... 55
REAR FOG LAMP ..................................................... 56
System Description ................................................. 56
DESCRIPTION .................................................... 56
FOG LAMP OPERATION .................................... 56
Wiring Diagram -R/FOG-/Without Front Fog Lamp ... 57
Wiring Diagram -R/FOG-/With Front Fog Lamp ..... 58
Bulb Replacement .................................................. 59
Removal and Installation ........................................ 59
REMOVAL ........................................................... 59
INSTALLATION .................................................... 59
CLEARANCE LAMP/TAIL LAMP ............................. 60
Bulb Replacement (Clearance Lamp) .................... 60
Bulb Replacement (Tail lamp) ................................. 60
Removal and Installation of Clearance Lamp ......... 60
Removal and Installation of Tail lamp ..................... 60HIGH-MOUNTED STOP LAMP ................................. 61
Bulb Replacement ................................................... 61
Removal and Installation ......................................... 61
REAR COMBINATION LAMP ................................... 62
Wiring Diagram —STOP/L— .................................. 62
Bulb Replacement ................................................... 63
Removal and Installation ......................................... 63
REMOVAL ............................................................ 63
INSTALLATION .................................................... 63
COMBINATION SWITCH .......................................... 64
Removal and Installation ......................................... 64
Switch Circuit Inspection ......................................... 64
ASHTRAY ILLUMINATION ....................................... 65
Bulb Replacement, Removal and Installation ......... 65
ILLUMINATION .......................................................... 66
System Description ................................................. 66
Schematic ............................................................... 67
Wiring Diagram -ILL- ............................................... 68
LHD MODELS ...................................................... 68
RHD MODELS ..................................................... 72
INTERIOR ROOM LAMP .......................................... 76
System Description ................................................. 76
POWER SUPPLY AND GROUND ....................... 76
SWITCH OPERATION ......................................... 76
INTERIOR ROOM LAMP TIMER OPERATION ... 77
ON-OFF CONTROL ............................................. 77
Wiring Diagram -ROOM/L- ...................................... 78
LHD MODELS ...................................................... 78
RHD MODELS ..................................................... 80
Interior Room Lamp Timer Does Not Operate ........ 82
Interior Room Lamp Timer Does Not Cancel .......... 85
Bulb Replacement ................................................... 86
INTERIOR ROOM LAMP ..................................... 86
LUGGAGE ROOM LAMP .................................... 86
Removal and Installation ......................................... 87
INTERIOR ROOM LAMP ..................................... 87
LUGGAGE ROOM LAMP .................................... 87
STEP LAMP .............................................................. 88
Wiring Diagram — STEP/L — ................................. 88
LHD MODELS ...................................................... 88
RHD MODELS ..................................................... 89
MAP LAMP ................................................................ 90
Wiring Diagram —INT/L— ...................................... 90
Bulb Replacement ................................................... 91
MAP LAMP (WITHOUT SUNROOF) ................... 91
MAP LAMP (WITH SUNROOF) ........................... 91
Removal and Installation ......................................... 91
MAP LAMP (WITHOUT SUNROOF) ................... 91
MAP LAMP (WITH SUNROOF) ........................... 91
BULB SPECIFICATIONS .......................................... 92
Headlamp ................................................................ 92
Exterior Lamp .......................................................... 92
Interior Lamp/Illumination ........................................ 92

LT-76
INTERIOR ROOM LAMP

INTERIOR ROOM LAMPPFP:26410
System DescriptionEKS003BQ
POWER SUPPLY AND GROUND
Power is supplied at all times:

through 10A fuse [No. 28, located in the fuse block (J/B)]

to key switch terminal 1 and

to time control unit terminal 1

through 10A fuse [No. 26, located in the fuse block (J/B)]

to interior room lamp terminal 1

to luggage room lamp terminal 1

to map lamp terminal 1 (with sunroof models)
When the key is removed from ignition key cylinder, power is interrupted

through key switch terminal 2

to time control unit terminal 18.
With the ignition key switch in the ON or START position, power is supplied

through 10A fuse [No. 5, located in the fuse block (J/B)]

to time control unit terminal 17.
Ground is supplied

through grounds terminals M27 and M70

to time control unit terminal 16.
When the driver side front door is opened, ground is supplied

through grounds B8 and B18

to front door switch driver side terminal 3

from front door switch driver side terminal 2

to time control unit terminal 30.
When any door (except back door) is opened, ground is supplied

through case ground of each door switch

to each door switch terminal 1

to time control unit terminal 31.
When back door is opened, ground is supplied:

through ground D53

to back door switch terminal 3

from back door switch terminal 1

to time control unit terminal 31.
When the driver side door is unlocked, the time control unit receives a ground signal

through grounds terminals M27 and M70

to front door lock actuator terminal 1

from front door lock actuator terminal 5

to time control unit terminal 28.
When a signal, or combination of signals is received by the time control unit, ground is supplied

through time control unit terminal 26

to interior room lamp terminal 2.

to map lamp terminal 3 (with sunroof models)
With power and ground supplied, the interior room lamp illuminates.
SWITCH OPERATION
When interior room lamp switch is ON, ground is supplied

through case grounds of interior room lamp

to interior room lamp.

INTERIOR ROOM LAMP
LT-77
C
D
E
F
G
H
I
J
L
MA
B
LT

When map lamp switch is ON, ground is supplied (with sunroof models)

through ground M27 and M70

to map lamp terminal 2.
INTERIOR ROOM LAMP TIMER OPERATION
When interior room lamp nad map lamp (with sunroof models) switch is in the “DOOR” position, the time con-
trol unit keeps the interior room lamp and map lamp (with sunroof models) illuminated for about 30 seconds
when

unlock signal is supplied from driver's door unlock sensor while all doors are closed and key is out of igni-
tion key cylinder

key is removed from ignition key cylinder while all doors are closed

driver's door is opened and then closed while key is out of the ignition key cylinder. (However, if the
driver's door is closed with the key inserted in the ignition key cylinder after the driver's door is opened
with the key removed, the timer is operated.)
The timer is canceled when

driver's door is locked,

driver's door is opened, or

ignition switch is turned ON.
ON-OFF CONTROL
When the driver side door, front passenger door, rear LH or RH door is opened, the interior room lamp and
map lamp (with sunroof models) turns on while the interior room lamp and map lamp (with sunroof models)
switch is in the “DOOR” position.

MAP LAMP
LT-91
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS00F89
MAP LAMP (WITHOUT SUNROOF)
1. Remove the lens using a clip driver or a suitable tool.
2. Remove the shade mounting screw and remove the shade from
the map lamp.
3. Remove the bulb.
MAP LAMP (WITH SUNROOF)
1. Remove the lens using a clip driver or a suitable tool.
2. Remove the bulb.
Removal and InstallationEKS00F8A
MAP LAMP (WITHOUT SUNROOF)
1. Using a clips driver or a suitable tool, press and remove the
metal clip of the map lamp.
2. Disconnect the map lamp connector.
MAP LAMP (WITH SUNROOF)
1. Using a clips driver or a suitable tool, press and remove the
metal clip of the map lamp.
2. Disconnect the map lamp connector and sunroof connector.Map lamp (Without sunroof) : 12V 8W
PKIA5761E
Map lamp (With sunroof) : 12V 10W
SKIA0065E
PKIA0472E
SKIA0066E

LT-92
BULB SPECIFICATIONS

BULB SPECIFICATIONSPFP:26297
HeadlampEKS003GS
Exterior LampEKS003GT
Interior Lamp/IlluminationEKS003GU
Item Wattage (W)
Low/High55 /60(H4)
Driving lamp65(H1R1)
Item Wattage (W)
Front combination lamp Clearance lamp 5
Front turn signal lamp21(amber)
Side turn signal lamp5
Fog lampFront fog lamp 55(H11)
Rear fog lamp 21
Rear combination lampStop/Tail lamp 21/5
Turn signal lamp 21
Back-up lamp 21
License plate lamp5
High-mounted stop lamp5
Item Wattage (W)
Ashtray illumination1.4
Interior room lamp10
Spot lampWithout sunroof 8
With sunroof 10
Luggage room lamp10