2003 NISSAN X-TRAIL battery

EM-38
[QR]
FUEL INJECTOR AND FUEL TUBE

b. With the sleeve side of quick connector release facing quick connector, install quick connector release
onto fuel tube.
c. Insert quick connector release into quick connector until sleeve
contacts and goes no further. Hold quick connector release on
that position.
CAUTION:
Inserting quick connector release hard will not disconnect
quick connector. Hold quick connector release where it
contacts and goes no further.
d. Draw and pull out quick connector straight from fuel tube.
CAUTION:

Pull quick connector holding “A” position in the figure.

Do not pull with lateral force applied. O-ring inside quick
connector may be damaged.

Prepare container and cloth beforehand as fuel will leak out.

Avoid fire and sparks.

Keep parts away from heat source. Especially, be careful when welding is performed around
them.

Do not expose parts to battery electrolyte or other acids.

Do not bend or twist connection between quick connector and fuel feed hose during installa-
tion/removal.

To keep clean the connecting portion and to avoid dam-
age and foreign materials, cover them completely with
plastic bags or something similar.
4. Remove intake manifold collector. Refer to EM-20, "
Removal and Installation (QR25DE)" .
5. Disconnect sub-harness for fuel injector.
6. Loosen mounting bolts in reverse order as shown in the figure.
7. Remove fuel tube and fuel injector assembly and insulators.
CAUTION:

When removing, be careful to avoid any interference with
fuel injector.

Use a shop cloth to absorb any fuel leaks from fuel tube.
KBIA0702E
PBIC2205E
KBIA0239E

CYLINDER HEAD
EM-67
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

CYLINDER HEADPFP:11041
On-Vehicle ServiceEBS00KNP
CHECKING COMPRESSION PRESSURE
1. Warm up engine thoroughly. Then, stop it.
2. Release fuel pressure by “Without CONSULT-II”. Refer to EC-48, "
FUEL PRESSURE RELEASE" (WITH
EURO-OBD) or EC-510, "
FUEL PRESSURE RELEASE" (WITHOUT EURO-OBD).

Leave fuel pump fuse disconnecting to avoid fuel injection during measurement.
3. Remove ignition coil and spark plug from each cylinder. Refer to EM-29, "
IGNITION COIL" and EM-30,
"SPARK PLUG" .
4. Connect engine tachometer (not required in use of CONSULT-II).
5. Install compression tester with adapter onto spark plug hole.

Use compression gauge whose picking up end inserted to
spark plug hole is smaller than 20 mm (0.79 in) in diameter.
Otherwise, it may be caught by cylinder head during removal.
6. With accelerator pedal fully depressed, turn ignition switch to “START” for cranking. When the gauge
pointer stabilizes, read the compression pressure and engine rpm. Perform these steps to check each cyl-
inder.
Compression pressure:
Unit: kPa (bar, kg/cm2 , psi) /rpm
CAUTION:
Always use a fully changed battery to obtain specified engine speed.

If the engine speed is out of specified range, check battery liquid for proper gravity. Check engine
speed again with normal battery gravity.

If compression pressure is below minimum value, check valve clearances and parts associated with
combustion chamber (Valve, valve seat, piston, piston ring, cylinder bore, cylinder head, cylinder head
gasket). After the checking, measure the compression pressure again.

If some cylinders have low compression pressure, pour small amount of engine oil into the spark plug
hole of the cylinder to re-check it for compression.
–If the added engine oil improves the compression, piston rings may be worn out or damaged. Check
piston rings and replace if necessary.
KBIA0130E
SBIA0533E
Engine type Standard Minimum Differential limit between cylinders
QR20DE 1,190 (11.9, 12.1, 173) / 250 990 (9.9, 10.1, 144) / 250
100 (1.0, 1.0, 14) / 250
QR25DE 1,250 (12.5, 12.8, 181) / 250 1,060 (10.6, 10.8, 154) / 250

ENGINE ASSEMBLY
EM-79
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

Preparation
1. Remove hood assembly. Refer to BL-12, "HOOD" .
2. Release fuel pressure. Refer to EC-48, "
FUEL PRESSURE RELEASE" (WITH EURO-OBD) or EC-510,
"FUEL PRESSURE RELEASE" (WITHOUT EURO-OBD).
3. Disconnect both battery terminals. Refer to SC-3, "
BATTERY" .
4. Drain engine coolant from radiator. Refer to CO-9, "
DRAINING ENGINE COOLANT" .
5. Remove the following parts.

LH and RH undercovers

Front road wheels and tyres

Battery; Refer to SC-3, "BATTERY" .

Drive belt; Refer to EM-13, "DRIVE BELTS" .

Air duct and air cleaner case assembly; Refer to EM-15, "AIR CLEANER AND AIR DUCT" .

Alternator; Refer to SC-12, "CHARGING SYSTEM" .

Radiator and radiator cooling fan assembly; Refer to CO-12, "RADIATOR" .
6. Disconnect engine room harness from the engine side and set it aside for easier work.
7. Disconnect all vacuum hoses and air hoses connected to vehicle side at engine side.
Engine Room LH
1. Disconnect fuel feed hose, and plug it to prevent fuel from draining. Refer to EM-32, "FUEL INJECTOR
AND FUEL TUBE"
2. Disconnect heater hose, and install plug it to prevent engine coolant from draining.
3. Disconnect control cable from transaxle (A/T models). Refer to AT- 4 0 4 , "
ON-VEHICLE SERVICE" .
4. Disconnect clutch operating cylinder from transaxle, and move it aside (M/T models). Refer to CL-10,
"OPERATING CYLINDER" .
5. Disconnect shift and select cable from transaxle (M/T models). Refer to MT-14, "
CONTROL LINKAGE" .
Engine Room RH
1. Remove engine coolant reservoir tank. Refer to CO-12, "RADIATOR" .
2. Remove A/C compressor with piping connected from engine. Temporarily secure it on vehicle side with a
rope to avoid putting load on it. Refer to ATC-144, "
Removal and Installation of Compressor" .
Vehicle Underbody
1. Remove exhaust front tube. Refer to EX-2, "EXHAUST SYSTEM" .
2. Remove propeller shaft. Refer to PR-3, "
REAR PROPELLER SHAFT" .
3. Remove steering lower joint from steering gear. Refer to PS-10, "
STEERING COLUMN" .
4. Disconnect power steering fluid piping at a point between vehicle and engine. Refer to PS-34, "
HYDRAU-
LIC LINE" .
5. Remove rear plate cover from oil pan (upper). Then remove bolts fixing drive plate to torque converter
(A/T models). Refer to EM-25, "
OIL PAN AND OIL STRAINER" and AT- 4 1 3 , "REMOVAL AND INSTALLA-
TION" .
6. Remove transaxle joint bolts which pierce at oil pan (upper) lower rear side. Refer to MT-17, "
TRAN-
SAXLE ASSEMBLY" (M/T models) or AT- 4 1 3 , "REMOVAL AND INSTALLATION" (A/T models).
7. Remove front wheel sensor (LH and RH) for ABS from steering knuckle. Refer to BRC-45, "
WHEEL SEN-
SORS" (ABS) or BRC-116, "WHEEL SENSORS" (ESP/TCS/ABS).
8. Remove brake caliper assembly with piping connected from steering knuckle. Temporarily secure it on
vehicle side with a rope to avoid load on it. Refer to BR-27, "
FRONT DISC BRAKE" .
9. Remove lower ends of left and right strut from steering knuckle. Refer to FSU-5, "
FRONT SUSPENSION
ASSEMBLY" .
Removal
1. Install engine slingers into front left of cylinder head and rear right of cylinder head.

EM-196
[YD22DDTi]
CYLINDER HEAD

CYLINDER HEADPFP:11041
On-Vehicle ServiceEBS00LRV
CHECKING COMPRESSION PRESSURE
1. Warm up engine thoroughly. Then, stop it.
2. Using CONSULT-II, make sure no error codes are indicated for self-diagnosis items. Refer to EC-905,
"Basic Inspection" (WITH EURO-ODB) or EC-1231, "Basic Inspection" (WITHOUT EURO-ODB).

Do not disconnect CONSULT-II until the end of this operation; it will be used to check engine rpm and
for error detection at the end of this operation.
3. Disconnect the negative battery terminal.
4. Remove charge air cooler. Refer to EM-135, "
Removal and Installation"
5. To prevent fuel from being injected during inspection, remove
fuel pump fuse [ENG CONT 2 (20A)] from fuse box on the left
side of engine room.

Among marks on fuse box, [ENG CONT 2 (20A)] is for fuel
pump fuse.
6. Remove glow plugs from all the cylinders. Refer to EM-152,
"Removal and Installation" .
CAUTION:

Before removal, clean the surrounding area to prevent
entry of any foreign materials into engine.

Carefully remove glow plugs to prevent any damage or
breakage.

Handle with care to avoid applying any shock to glow plugs.
7. Install compression gauge adapter (special service tool) to
installation holes of glow plugs and connect compression gauge
for diesel engine.
8. Connect battery negative terminal.
9. With accelerator pedal fully depressed, turn ignition switch to
“START” for cranking. When the gauge pointer stabilizes, read
the compression pressure and engine rpm. Perform these steps
to check each cylinder.

Always use a fully-charged battery to obtain specified engine
speed.
Compression pressure
Unit: kPa (bar, kg/cm2 , psi)/rpm

When engine rpm is out of the specified range, check the specific gravity of battery liquid. Measure
again under corrected conditions.

If engine rpm exceeds the limit, check valve clearance and combustion chamber components (valves,
valve seats, cylinder head gaskets, piston rings, pistons, cylinder bores, cylinder block upper and lower
surfaces) and measure again.

If compression pressure is low in some cylinders, apply engine oil from glow plug installation hole. Then
check pressure again.
–If compression pressure becomes normal after applying engine oil, piston ring may be worn or dam-
aged. Check piston ring for malfunction. If any, replace piston ring.
–If compression pressure is still low after applying engine oil, valve may be malfunctioning. Check valve
for malfunction. If contact malfunction is found, replace valve or valve seat.

If compression pressure in adjacent two cylinders is low after applying engine oil, pressure may be
leaking from gasket. In this case, replace cylinder head gasket.
PBIC0680E
: 18 - 22 N·m (1.8 - 2.2 kg-m, 13 - 16 ft-lb)
SEM112G
Standard Minimum Difference limit between cylinders
2,991 (29.9, 30.5, 434)/200 2,452 (24.5, 25.0, 356)/200 490 (4.9, 5.0, 71)/200

CYLINDER HEAD
EM-197
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

10. Complete this operation as follows:
a. Turn the ignition switch to “OFF”.
b. Disconnect battery negative terminal.
c. Install glow plug and install all the parts removed in step 4.
d. Install fuel pump fuse [ENG CONT (20A)].
e. Connect battery negative terminal.
f. Using CONSULT-II make sure no DTC is indicated for items of self-diagnosis.
Removal and InstallationEBS00LRW
REMOVAL
1. Drain engine coolant. Refer to CO-31, "Changing Engine Coolant" .
2. Remove the following:

Charge air cooler (Refer to EM-135, "Removal and Installation" .)

Rocker cover (Refer to EM-168, "Removal and Installation" .)

Air cleaner and air duct (Refer to EM-133, "Removal and Installation" .)

Vacuum pump (Refer to EM-153, "Removal and Installation" .)

Spill tube and fuel injector (Refer to EM-157, "Removal and Installation" .)

Intake manifold (Refer to EM-136, "Removal and Installation" .)

Exhaust manifold and Turbocharger (Refer to EM-141, "Removal and Installation" .)

Secondary timing chain (Refer to EM-180, "Removal and Installation" .)

Camshaft (Refer to EM-170, "Removal and Installation" .)
3. Remove cylinder head assembly.
1. Glow plug 2. Cylinder head assembly 3. Cylinder head bolt
4. Copper washer 5. Engine coolant temperature sensor 6. Gasket
7. Water outlet 8. Dowel pin 9. Gasket
10. Glow harness 11. Glow plate 12. Cap
PBIC2437E

ENGINE ASSEMBLY
EM-209
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

REMOVAL
Description of work
Remove engine, transaxle and transfer assembly with front suspension member from vehicle downward. Sep-
arate suspension member, and then separate engine and transaxle.
Preparation
1. Remove hood assembly. Refer to BL-12, "HOOD" .
2. Drain engine coolant from radiator drain plug. Refer to CO-31, "
DRAINING ENGINE COOLANT" .
3. Remove the following parts.

LH/RH engine undercover

LH/RH front wheels

Battery; Refer to SC-3, "BATTERY" .

Drive belts; Refer to EM-132, "Removal and Installation" .

Air duct and air cleaner case assembly; Refer to EM-133, "Removal and Installation" .

Alternator; Refer to SC-16, "Removal and Installation" .

Radiator and cooling fan assembly; Refer to CO-34, "Removal and Installation" and CO-36, "COOL-
ING FAN" .

Charge air cooler; Refer to EM-135, "CHARGE AIR COOLER" .
4. Disconnect engine room harness from the engine side and set it aside for easier work.
5. Disconnect all the body-side vacuum hoses and air hoses at engine side.
Engine room LH
1. Disconnect fuel feed hose and return hose, and plug it to prevent fuel from draining. Refer to EM-136,
"INTAKE MANIFOLD" .
2. Disconnect heater hose, and install plug it to prevent engine coolant from draining. Refer to EM-136,
"INTAKE MANIFOLD" .
3. Remove clutch operating cylinder from transaxle, and move it aside. Refer to MT-17, "
TRANSAXLE
ASSEMBLY" and CL-10, "OPERATING CYLINDER" .
4. Disconnect shift cable from transaxle. Refer to MT-14, "
CONTROL LINKAGE" .
Engine room RH
1. Remove engine coolant reservoir tank. Refer to CO-34, "RADIATOR" .
2. Remove A/C compressor with piping connected from engine. Temporarily secure it on body with a rope to
avoid putting load on it. Refer to ATC-144, "
Removal and Installation of Compressor" .
Vehicle underbody
1. Remove exhaust front tube. Refer to EX-2, "Removal and Installation" .
2. Remove propeller shaft. Refer to PR-4, "
Removal and Installation" .
3. Remove steering shaft from steering gear. Refer to PS-10, "
STEERING COLUMN" .
4. Disconnect power steering fluid cooler piping at a point between body and engine. Refer to PS-34,
"HYDRAULIC LINE" .
5. Remove ABS sensor from brake caliper. Refer to BRC-45, "
WHEEL SENSORS" (ABS), BRC-116,
"WHEEL SENSORS" (ESP/TCS/ABS).
6. Remove brake caliper with piping connected from steering knuckle. Temporarily secure it on body with a
rope to avoid load on it. Refer to BR-27, "
FRONT DISC BRAKE" .
7. Remove left and right suspensions from steering knuckle under strut. Refer to FSU-5, "
FRONT SUSPEN-
SION ASSEMBLY" .

EC-12 CONSULT-II Reference Value in Data Monitor Mode
1074
ECM Terminals and Reference Value ..................1074
On Board Diagnosis Logic ...................................1074
DTC Confirmation Procedure ..............................1075
Wiring Diagram ....................................................1076
Diagnostic Procedure ..........................................1077
Component Inspection .........................................1078
Removal and Installation .....................................1079
DTC P0404 EGR VOLUME CONTROL VALVE .....1080
Description ...........................................................1080
CONSULT-II Reference Value in Data Monitor Mode
1081
ECM Terminals and Reference Value ..................1081
On Board Diagnosis Logic ...................................1081
DTC Confirmation Procedure ..............................1081
Wiring Diagram ....................................................1083
Diagnostic Procedure ..........................................1084
Component Inspection .........................................1085
Removal and Installation .....................................1086
DTC P0563 BATTERY VOLTAGE .........................1087
On Board Diagnosis Logic ...................................1087
DTC Confirmation Procedure ..............................1087
Diagnostic Procedure ..........................................1087
DTC P0605 ECM ....................................................1089
Description ...........................................................1089
On Board Diagnosis Logic ...................................1089
DTC Confirmation Procedure ..............................1089
Diagnostic Procedure ..........................................1090
DTC P0606 ECM ....................................................1091
Description ...........................................................1091
On Board Diagnosis Logic ...................................1091
DTC Confirmation Procedure ..............................1091
Diagnostic Procedure ..........................................1092
DTC P0628, P0629 FUEL PUMP ...........................1093
Description ...........................................................1093
CONSULT-II Reference Value in Data Monitor Mode
1093
ECM Terminals and Reference Value ..................1093
On Board Diagnosis Logic ...................................1094
DTC Confirmation Procedure ..............................1094
Wiring Diagram ....................................................1095
Diagnostic Procedure ..........................................1096
Component Inspection .........................................1097
Removal and Installation .....................................1097
DTC P0642, P0643 SENSOR POWER SUPPLY ...1098
Description ...........................................................1098
CONSULT-II Reference Value in Data Monitor Mode
1098
ECM Terminals and Reference Value ..................1098
On Board Diagnosis Logic ...................................1099
DTC Confirmation Procedure ..............................1099
Wiring Diagram ....................................................11 0 0
Diagnostic Procedure ..........................................11 0 1
Component Inspection .........................................11 0 2
Removal and Installation .....................................11 0 3
DTC P0652, P0653 SENSOR POWER SUPPLY ...110 4
Description ...........................................................11 0 4
CONSULT-II Reference Value in Data Monitor Mode 11 0 4
ECM Terminals and Reference Value ..................11 0 4
On Board Diagnosis Logic ...................................11 0 5
DTC Confirmation Procedure ...............................11 0 5
Wiring Diagram ....................................................11 0 6
Diagnostic Procedure ...........................................11 0 7
Component Inspection .........................................11 0 8
Removal and Installation ......................................11 0 9
DTC P0686 ECM RELAY .......................................1110
ECM Terminals and Reference valve ...................111 0
On Board Diagnosis Logic ...................................111 0
DTC Confirmation Procedure ...............................111 0
Wiring Diagram ....................................................1111
Diagnostic Procedure ...........................................111 2
Component Inspection .........................................111 2
DTC P1211 TCS CONTROL UNIT .........................1113
Description ...........................................................111 3
On Board Diagnosis Logic ...................................111 3
DTC Confirmation Procedure ...............................111 3
Diagnostic Procedure ...........................................111 3
DTC P1212 TCS COMMUNICATION LINE ............1114
Description ...........................................................111 4
On Board Diagnosis Logic ...................................111 4
DTC Confirmation Procedure ...............................111 4
Diagnostic Procedure ...........................................111 4
DTC P1260 - P1267 FUEL INJECTOR ADJUST-
MENT RESISTOR ...................................................1115
Description ...........................................................111 5
ECM Terminals and Reference Value ..................111 5
On Board Diagnosis Logic ...................................111 5
DTC Confirmation Procedure ...............................111 6
Wiring Diagram ....................................................111 7
Diagnostic Procedure ...........................................111 8
Component Inspection .........................................111 9
Removal and Installation ......................................11 2 0
DTC P1268 - P1271 FUEL INJECTOR ..................11 21
Component Description .......................................11 2 1
CONSULT-II Reference Value in Data Monitor Mode
11 2 1
ECM Terminals and Reference Value ..................11 2 1
On Board Diagnosis Logic ...................................11 2 2
DTC Confirmation Procedure ...............................11 2 3
Wiring Diagram ....................................................11 2 4
Diagnostic Procedure ...........................................11 2 5
Component Inspection .........................................11 2 6
Removal and Installation ......................................11 2 6
DTC P1272 FUEL PUMP .......................................11 27
Description ...........................................................11 2 7
CONSULT-II Reference Value in Data Monitor Mode
11 2 7
ECM Terminals and Reference Value ..................11 2 7
On Board Diagnosis Logic ...................................11 2 8
DTC Confirmation Procedure ...............................11 2 8
Wiring Diagram ....................................................11 2 9
Diagnostic Procedure ...........................................11 3 0
Component Inspection .........................................11 3 2
Removal and Installation ......................................11 3 3
DTC P1273 FUEL PUMP .......................................11 34
Description ...........................................................11 3 4

EC-16 ECM Terminals and Reference Value ..................1369
On Board Diagnosis Logic ...................................1369
DTC Confirmation Procedure ..............................1370
Wiring Diagram ....................................................1371
Diagnostic Procedure ..........................................1372
Component Inspection .........................................1375
Removal and Installation .....................................1375
DTC P0563 BATTERY VOLTAGE .........................1376
On Board Diagnosis Logic ...................................1376
DTC Confirmation Procedure ..............................1376
Diagnostic Procedure ..........................................1376
DTC P0605 ECM ....................................................1378
Description ...........................................................1378
On Board Diagnosis Logic ...................................1378
DTC Confirmation Procedure ..............................1378
Diagnostic Procedure ..........................................1378
DTC P0606 ECM ....................................................1380
Description ...........................................................1380
On Board Diagnosis Logic ...................................1380
DTC Confirmation Procedure ..............................1380
Diagnostic Procedure ..........................................1380
DTC P0628, P0629 FUEL PUMP ...........................1382
Description ...........................................................1382
CONSULT-II Reference Value in Data Monitor Mode
1382
ECM Terminals and Reference Value ..................1382
On Board Diagnosis Logic ...................................1383
DTC Confirmation Procedure ..............................1383
Wiring Diagram ....................................................1384
Diagnostic Procedure ..........................................1385
Component Inspection .........................................1386
Removal and Installation .....................................1386
DTC P0642, P0643 SENSOR POWER SUPPLY ...1387
Description ...........................................................1387
CONSULT-II Reference Value in Data Monitor Mode
1387
ECM Terminals and Reference Value ..................1387
On Board Diagnosis Logic ...................................1388
DTC Confirmation Procedure ..............................1388
Wiring Diagram ....................................................1389
Diagnostic Procedure ..........................................1390
Component Inspection .........................................1391
Removal and Installation .....................................1392
DTC P0652, P0653 SENSOR POWER SUPPLY ...1393
Description ...........................................................1393
CONSULT-II Reference Value in Data Monitor Mode
1393
ECM Terminals and Reference Value ..................1393
On Board Diagnosis Logic ...................................1394
DTC Confirmation Procedure ..............................1394
Wiring Diagram ....................................................1395
Diagnostic Procedure ..........................................1396
Component Inspection .........................................1397
Removal and Installation .....................................1398
DTC P0686 ECM RELAY .......................................1399
ECM Terminals and Reference valve ..................1399
On Board Diagnosis Logic ...................................1399
DTC Confirmation Procedure ..............................1399
Wiring Diagram ....................................................1400Diagnostic Procedure ...........................................1401
Component Inspection .........................................1401
DTC P1211 TCS CONTROL UNIT .........................1402
Description ...........................................................1402
On Board Diagnosis Logic ...................................1402
DTC Confirmation Procedure ...............................1402
Diagnostic Procedure ...........................................1402
DTC P1212 TCS COMMUNICATION LINE ............1403
Description ...........................................................1403
On Board Diagnosis Logic ...................................1403
DTC Confirmation Procedure ...............................1403
Diagnostic Procedure ...........................................1403
DTC P1260 - P1267 FUEL INJECTOR ADJUST-
MENT RESISTOR ...................................................1404
Description ...........................................................1404
ECM Terminals and Reference Value ..................1404
On Board Diagnosis Logic ...................................1404
DTC Confirmation Procedure ...............................1405
Wiring Diagram ....................................................1406
Diagnostic Procedure ...........................................1407
Component Inspection .........................................1408
Removal and Installation ......................................1409
DTC P1268 - P1271 FUEL INJECTOR ..................1410
Component Description .......................................1410
CONSULT-II Reference Value in Data Monitor Mode
1410
ECM Terminals and Reference Value ..................1410
On Board Diagnosis Logic ...................................1411
DTC Confirmation Procedure ...............................1412
Wiring Diagram ....................................................1413
Diagnostic Procedure ...........................................1414
Component Inspection .........................................1415
Removal and Installation ......................................1415
DTC P1272 FUEL PUMP .......................................1416
Description ...........................................................1416
CONSULT-II Reference Value in Data Monitor Mode
1416
ECM Terminals and Reference Value ..................1416
On Board Diagnosis Logic ...................................1417
DTC Confirmation Procedure ...............................1417
Wiring Diagram ....................................................1418
Diagnostic Procedure ...........................................1419
Component Inspection .........................................1420
Removal and Installation ......................................1420
DTC P1273 FUEL PUMP .......................................1422
Description ...........................................................1422
CONSULT-II Reference Value in Data Monitor Mode
1422
ECM Terminals and Reference Value ..................1422
On Board Diagnosis Logic ...................................1423
DTC Confirmation Procedure ...............................1423
Wiring Diagram ....................................................1424
Diagnostic Procedure ...........................................1425
Component Inspection .........................................1426
Removal and Installation ......................................1426
DTC P1274 FUEL PUMP .......................................1427
Description ...........................................................1427
CONSULT-II Reference Value in Data Monitor Mode
1427