Page 221 of 304
221 Practical hints
Replacing bulbs
Replacing bulbs
Safe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See your autho-
rized Mercedes-Benz Center for headlamp
adjustment (
page 226).
Bulbs Front lamps
Lamp
Type
1
Additional turn
signal lamps
LED
2
Low beam
H7 (55 W)
Xenon*
D2R-35 W
3
Parking, standing
and turn signal lamp
2375 NA
4
High beam
H7 (55 W)
5
Fog lamp
HB4 (55 W)
6
Side marker lamp
W5W
Page 222 of 304
222 Practical hintsReplacing bulbsRear lamps Notes on bulb replacement
Use only 12-volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Your hands should be dry and free of oil
and grease.
If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Center.
Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Center.
Additional turn signals in the
exterior rear view mirrors
High mounted brake lamp
Xenon* lamps
Front fog lamps
Lamp
Type
7
Brake lamp
1154 / 32 cp
8
High mounted brake
lamp
LED
9
Backup lamp
1154 / 32 cp
10
Turn signal lamp
1156 NA
11
Tail, parking, stand-
ing and side marker
lamp
67 / 4 cp
12
License plate lamps
C5W
13
Rear fog lamp,
driver’s side
1155 / 32 cp
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot.
Allow the lamp to cool down before
changing a bulb.
Halogen lamps contain pressurized gas.
A bulb can explode if you:
touch or move it when hot
drop the bulb
scratch the bulb
Wear eye and hand protection.
Because of high voltage in xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
Page 223 of 304
223 Practical hints
Replacing bulbs
Replacing bulbs for front lamps
Low and high beam headlamps (Halo-
gen headlamps only)
Switch off the lights.
Open the hood (
page 171).
1Headlamp cover with locking tab
Push down locking tab at top and end
of headlamp cover1 and remove.2Electrical connector for low beam
headlamp bulb
3Electrical connector for high beam
headlamp bulb
Pull off electrical connector2 or3.
Unhook clamping ring and pull out the
bulb together with clamping ring.
Remove bulb.
Insert new bulb so that bulb sits prop-
erly in cutouts of bulb socket.
Mount clamping ring and reinstall.
Plug electrical connector onto the bulb.
Reinstall headlamp cover1.Low and high beam headlamps (Xenon*
headlamps only)
Warning!
G
Do not remove the cover for the xenon head-
lamp. Because of high voltage in xenon
lamps, it is dangerous to replace the bulb or
repair the lamp and its components. We rec-
ommend that you have such work done by a
qualified technician.
Page 224 of 304
224 Practical hintsReplacing bulbsParking, standing and turn signal lamp
Switch off the lights.
Open the hood (
page 171).
1Release opening
Insert the screwdriver from the vehicle
tool kit into release opening1.
Press the top of the screwdriver toward
the middle of the vehicle and toward
the rear.
The turn signal lamp will be lifted out.
Pull the turn signal lamp slightly out of
its mounting.
Pull off the electrical connector from
the turn signal lamp.
You can now take the turn signal lamp
completely out of its mounting.
Twist bulb socket counterclockwise
and pull out.
Gently push bulb into socket, turn
counterclockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinstall bulb socket, push in and twist
clockwise.
Plug electrical connector back into the
turn signal lamp.2Guides
3Tabs
Slide the turn signal lamp with tabs3
into guides2 and press it toward the
rear into the mounting until it engages.
Page 225 of 304
225 Practical hints
Replacing bulbs
Side marker lamp bulb
Switch off the lights.
Carefully slide lamp towards front.
Remove rear end first.
Twist bulb socket counterclockwise
and pull out.
Gently push bulb into socket, turn
counterclockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinstall bulb socket, push in and twist
clockwise.
To reinstall lamp, set rear end in
bumper and let front end snap into
place.
Replacing bulbs for rear lamps
Tail lamp assemblies
1Brake lamp
2Turn signal lamp
3Tail, parking and standing lamp, side
marker
4Backup lamp
5Rear fog lamp (driver’s side)
Switch off the lights.
Open trunk lid (
page 77).
Remove cover in right side panel.
Remove first aid kit (
page 206).
Remove cover in left side panel.
Turn bulb socket counterclockwise and
pull out.
Gently push bulb into socket, turn
counterclockwise and remove.
Insert new bulb in socket, push in and
turn clockwise.
Reinstall bulb socket, push in and turn
clockwise.
Close cover.
Page 226 of 304
226 Practical hintsReplacing bulbsLicense plate lamp
1Screws
Switch off the lights.
Loosen both screws1 and remove
lamp.
Replace the tubular lamp and reinstall
lamp.
Retighten the screws.Adjusting headlamp aim
(Halogen headlamps only)
Correct headlamp adjustment is extremely
important. Have the adjustment checked
regularly by an authorized
Mercedes-Benz Center.
To check and readjust a headlamp, follow
the steps described:
Park vehicle on level surface.
Open hood (
page 171).Vertical headlamp aim
1Headlamp vertical adjusting screw
2Level
iLow beam adjustments simultaneously
aim the high beam.
Vehicle should have a normal trunk
load.
Vertical aim adjustments change hori-
zontal aim.
Page 232 of 304
232 Practical hintsFlat tireInflating the tire
1Flap
2Air hose with pressure gauge and vent
screw
3Union nut
4Electrical plug
Open flap1 on air pump.
Pull out electrical plug4 and air hose
with pressure gauge2.
Screw union nut3 with air hose2 on to
the tire valve.
Insert electrical plug4 into vehicle
cigarette lighter socket.
Turn key in steering lock to position1
(page 29).
PressI on the electric air pump switch.
The electric air pump should now
switch on and inflate the tire.
After 5 minutes, the pressure gauge must
display at least 26 psi (1.8 bar). The air
hose and the union nut can become hot
during inflation. Please exercise appropri-
ate caution.
If this tire pressure is not attained, turn
off the electric air pump, detach the air
hose from the tire valve, and again
drive vehicle back and forth very slowly
approximately 30 ft (10 m).
This serves to better distribute the
TIREFIT sealant material inside the tire.
Inflate the tire again.
Press0 on the electric air pump
switch.
Turn key in steering lock to position0.
The electric air pump should now be
switched off.
Warning!
G
Observe safety instructions on air pump la-
bel.
!Do not exceed the maximum pressure
of 36 psi (2.5 bar).
!Do not operate the electric air pump
longer than eight minutes without in-
terruption. Otherwise it may overheat.
You may operate the air pump again af-
ter it has cooled off.
Page 236 of 304
236 Practical hintsFlat tire
Unscrew the valve cap from tire
valve7.
Screw filler hose10 onto tire valve7.
Insert electrical plug4 into vehicle cig-
arette lighter socket.
Turn key in steering lock to position1
(page 29).
PressI on electric air pump switch8.
The electric air pump should now
switch on and inflate the tire.After 5 minutes, the pressure gauge must
display at least 26 psi (1.8 bar). The air
hose can become hot during inflation.
Please exercise appropriate caution.
If this tire pressure is not attained, turn
off the electric air pump, detach the fill-
er hose from the tire valve, and drive
vehicle back and forth very slowly ap-
proximately 30 ft (10 m).
This serves to better distribute the
TIREFIT sealant material inside the tire.
Unscrew the air pump’s air hose5 from
flange6 of the TIREFIT container.
Inflate the tire again.
After attaining a tire pressure of 26 psi
(1.8 bar), press0 on electric air pump
switch8.
The electric air pump should now be
switched off.
Turn key in steering lock to position0
(page 29).
!Do not operate the electric air pump
longer than eight minutes without in-
terruption. Otherwise it may overheat.
You may operate the air pump again af-
ter it has cooled off.
Warning!
G
If a tire pressure of 26 psi (1.8 bar) is not at-
tained, tire is too severely damaged for
TIREFIT to provide a reliable tire repair.
In this case, TIREFIT cannot properly seal
the tire.
Do not drive the vehicle.
Contact the nearest Mercedes-Benz Center
or call Roadside Assistance.
