2003 MERCEDES-BENZ ML350 parking

247 Practical hints
Replacing bulbs
Replacing bulbs
Safe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See your autho-
rized Mercedes-Benz Light Truck Center
for headlamp adjustment.
Bulbs Front lamps
iIf the headlamps are fogged up on the
inside as a result of high humidity, driv-
ing the vehicle a distance should clear
out the fogging.
Lamp
Type
1
Fog lamp
H8 35 W
2
High beam
H7 (55 W)
3
Low beam
H7 (55 W)
Xenon* D2S-35 W
4
Turn signal,
parking, stand-
ing and side
marker lamp
1157 NA
(32/3 cp bulb)
5
Additional turn
signal
LED

248 Practical hintsReplacing bulbsRear lamps Notes on bulb replacement


Use only 12-volt bulbs of the same type
and with the specified watt rating.


Switch lights off before changing a bulb
to prevent short circuits.


Always use a clean lint-free cloth when
handling bulbs.


Your hands should be dry and free of oil
and grease.


If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Light Truck Center.


Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Light Truck Center:

Additional turn signals in the exteri-
or rear view mirrors


Bi-Xenon lamps*


Front fog lamps (vehicles with sport
package)*
Lamp
Type
6
Brake lamp
1073
(32 cp bulb)
7
Backup lamp
1073
(32 cp bulb)
8
Turn signal lamp
PY 21 W
9
Tail, parking and
standing lamp
Rear fog lamp, driv-
er’s side
P 21/4 W
10
Side marker lamp
W5W
11
High mounted brake
lamp
1073
(32 cp bulb)
12
License plate lamps
C 5 W
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you:

touch or move it when hot


drop the bulb


scratch the bulb
Wear eye and hand protection.
Because of high voltage in xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.

250 Practical hintsReplacing bulbsHigh beam bulbs
1High beam headlamp cover with lock-
ing tab
Switch off the lights.

Open the hood (
page 202).

Twist cover1 counterclockwise and re-
move.2Electrical connector

Pull electrical connector2 off.

Unclip the retainer springs and take out
the bulb.

Insert the new bulb so that the base lo-
cates in the recess on the holder.

Clip the retainer springs.

Plug the connector2 onto the bulb.

Align headlamp cover and click into
place.Turn signal, parking, standing and side
marker lamp bulbs
1Bulb socket

Switch off the lights.

Open the hood (
page 202).

Twist bulb socket1 counterclockwise
and pull out.

Push bulb into socket, turn counter-
clockwise and remove.

Insert new bulb in socket, push in and
twist clockwise.

Reinstall the bulb socket.


251 Practical hints
Replacing bulbs

Align headlamp cover and click into
place.
Fog lamp bulbs
1Fog lamp

Switch off the lights.

Use a suitable object (e.g. screwdriver)
to press on the release lever behind the
front panel.
Front fog lamp1 releases.

Remove fog lamp out of bumper.2Bulb socket
3Tabs

Twist bulb socket2 counterclockwise
to its end stop and pull out.

Pull bulb out of the bulb socket.

Insert new bulb in socket.

Reinstall bulb socket2.

Twist bulb socket2 clockwise to its
end stop.

Reinstall fog lamp into the bumper.
Make sure that tabs3 firmly seat into
the slots of holder.
Replacing bulbs for rear lamps
Tail lamp assemblies
Switch off the lights.

Open liftgate.
1Screws
2Tail, parking and standing lamp
Fog lamp, driver’s side
3Side marker lamp
4Turn signal lamp
5Backup lamp
6Brake lamp

Remove screws1.

Remove tail lamp.


255 Practical hints
Flat tire
Flat tire
Mounting the spare wheel Preparing the vehicle

Park the vehicle as far as possible from
moving traffic on a hard surface.

Turn on the hazard warning flashers.

Engage the steering wheel lock in the
straight ahead position and set the
parking brake.

Move the selector lever toP.

Have any passenger exit the vehicle at
a safe distance from the roadway.

Take the spare wheel out of its carrier
(page 239).
ML 55 AMG: (
page 240).Lifting the vehicle

Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
(not included) or other sizable objects.
When changing wheel on a level surface:

Place one chock in front of and one be-
hind the wheel that is diagonally oppo-
site to the wheel being changed.
When changing wheel on a hill:

Place chocks on the downhill side
blocking both wheels of the other axle.

Take the two-piece wheel wrench and
the jack out of the rear compartment
area (
page 237). Assemble wheel
wrench.
Warning!
G
The dimensions of the spare wheel are dif-
ferent from those of the road wheels. As a
result, the vehicle handling characteristics
change when driving with a mounted spare
wheel. Adapt your driving style accordingly.
The spare wheel is for temporary use only.
When driving with spare wheel mounted, en-
sure proper tire pressure and do not exceed
vehicle speed of 50 mph (80 km/h).
Drive to the nearest Mercedes-Benz Light
Truck Center as soon as possible to have the
spare wheel replaced with a regular road
wheel.
Never operate the vehicle with more than
one spare wheel mounted.

256 Practical hintsFlat tire

On wheel to be changed, loosen but do
not yet remove the wheel bolts (ap-
proximately one full turn with wrench).
The jack take-up brackets are located di-
rectly behind the front wheel housings and
in front of the rear wheel housings.1Take-up bracket
2Jack

Place jack on firm ground.

Position jack2 under the take-up
bracket1 so that it is always vertical
(plumb-line) as seen from the side,
even if the vehicle is parked on an in-
cline.

Jack up the vehicle until the wheel is a
maximum of 1.2 in (3 cm) from the
ground. Never start engine while vehi-
cle is raised.
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on level surface. Make sure that the jack
arm is fully seated in the jack take-up brack-
et. Always lower the vehicle onto sufficient
capacity jackstands before working under
the vehicle.
!Do not position the jack on the body of
the vehicle, as this may cause damage
to the vehicle.

265 Practical hints
Jump starting
The battery is located in the engine com-
partment.
Make sure that the two vehicles do not
touch.

Turn off all electrical consumers.

Apply parking brake.

Shift selector lever to positionP.1Positive terminal
2Cable clamps
3Negative terminal
4Cover

Remove cover4 from positive terminal
on both vehicles.

Connect positive terminals1 on the
batteries with the jumper cables. Start
with the charged battery.
!Jump starting may only be performed
on the battery installed in the engine
compartment.
Avoid repeated and lengthy starting at-
tempts.
Do not attempt to start the engine us-
ing a battery quick charge unit.
If engine does not run after several un-
successful starting attempts, have it
checked at the nearest authorized
Mercedes-Benz Light Truck Center.
Excessive unburned fuel generated by
repeated failed starting attempts may
damage the catalytic converter.
Make sure the jumper cables do not
have loose or missing insulation.
Make sure the cable clamps do not
touch any other metal part while the
other end is still attached to a battery.
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 261).

301 Index
B
BabySmart
TM
Airbag deactivation system 65
Compatible child seats 65, 293
Self-test 66
BabySmart
TM airbag deactivation
system 293
Backrest tilt 35
Backup lamps 248, 251
Bulbs 248
BAS 73, 293
Malfunction indicator lamp 225, 226
Warning lamp 225, 226
Batteries, remote control
Changing 243
Batteries, vehicle 207
Battery discharged
Jump starting 264
Battery indicator lamp
Indicator lamp 233
Battery, vehicle 207, 261
Charging 262
Disconnecting 261
Reconnecting 262
Reinstalling 262
Removing 262Bi-Xenon headlamps* 293
Block heater 214
Blocking
Rear door window operation 69
Brake assist system (BAS) 293
Brake fluid 286
Brake lamp bulbs 248
Brake lamp, high mounted 248
Brake pad wear
Indicator lamp 234
Brakes 180
Warning lamp 228
Break-in period 178
Bulbs, replacing 247
Additional turn signals 247
Backup lamps 248
Brake lamps 248
Fog lamps 247
Front fog lamp 251
Front lamps 247
High beam 247
High mounted brake lamp 248, 252
License plate lamps 248, 252
Low beam 247
Parking lamps 247, 248, 250
Rear fog lamp 248Rear fog lamps 251
Rear side marker lamp bulbs 251
Side marker lamps 247, 248, 250
Standing lamps 247, 248
Tail lamp assemblies 248, 251
Turn signal lamps 247, 248, 250
C
CAC (Customer Assistance Center) 293
Calibrating compass 174
California
Important notice 11
Calling up
Service indicator 216
CAN system 293
Capacities
Fuels, coolants, lubricants, etc. 284
Cargo area cover blind* 143
Closing 143
Installing 143
Opening 143
Removing 143
Cargo area see Cargo compartment 85
Cargo compartment
Liftgate 85
Lighting 109
Tie-down rings 140