Page 278 of 370
284 Practical hintsWhere will I find ...?Minispare wheel bolts
1Wheel bolt for light alloy rims
2Wheel bolt for Minispare wheel or other
steel rims
!Wheel bolts2 must be used when
mounting the Minispare wheel. The use
of any wheel bolts other than wheel
bolts 2 for the Minispare can cause
physical damage to the vehicle.
Warning!
G
Be sure to use the original length wheel
bolts when remounting the original wheel af-
ter it has been repaired.
S203 MY03_A.book Page 284 Tuesday, January 28, 2003 2:22 PM
Page 284 of 370
290 Practical hintsOpening/closing in an emergency
Opening/closing in an emergencySliding/pop-up roof
The sliding/pop-up roof drive is located
behind the lens of the interior overhead
light.
You can open or close the sliding/pop-up
roof manually should an electrical malfunc-
tion occur.
Pry off lens1 using a flat blade screw-
driver.
Slide both locking tabs2 in direction of
arrow.
Lower rear of cover and remove.
Remove cover.
Obtain crank3.
Insert crank3 through hole.
Turn crank3 clockwise to:
slide roof closed
raise roof at the rear
iDo not disconnect electrical connec-
tors.
S203 MY03_A.book Page 290 Tuesday, January 28, 2003 2:22 PM
Page 286 of 370
292 Practical hintsReplacing bulbs
Replacing bulbsSafe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See your autho-
rized Mercedes-Benz Center for headlamp
adjustment.
Bulbs Front lamps
iBackup bulbs will be brought into use
when the following lamps malfunction:
Standing lamps
Tail lamps
Lamp
Type
1
Additional turn
signal
LED
2
Turn signal lamp
Halogen
Turn signal lamp
Bi-Xenon*
1156 A
2357 A
3
Low beam Halogen
Low and high beam*
H7 (55 W)
Bi-Xenon*
4
High beam
H7 (55 W)
Parking and
standing lamps
W5W
5
Fog lamp
HB4/9006
(55 W)
6
Side marker lamp
W5W
S203 MY03_A.book Page 292 Tuesday, January 28, 2003 2:22 PM
Page 287 of 370
293 Practical hints
Replacing bulbs
Rear lamps Notes on bulb replacement
Use only 12 volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Your hands should be dry and free of oil
and grease.
If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Center.
Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Center:
Additional turn signals in the
exterior rear view mirrors
High mounted brake lamp
Xenon lamps
Front fog lamps
Lamp
Type
7
High mounted brake
lamp
LED
8
Brake lamp
P21W
9
Turn signal lamp
PY 21 W
10
Backup lamp
P21W
11
Tail, parking, stand-
ing and side marker
lamp
P21/4W
12
License plate lamps
C5W
13
Rear fog lamp,
driver’s side
P21/4W
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas.
A bulb can explode if you:
touch or move it when hot
drop the bulb
scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
S203 MY03_A.book Page 293 Tuesday, January 28, 2003 2:22 PM
Page 288 of 370
294 Practical hintsReplacing bulbsReplacing bulbs for front lamps
Halogen headlamps
1Bulb socket for turn signal lamp
2Headlamp cover for high beam head-
lamp and for parking and standing
lamp
3Headlamp cover for low beam head-
lamp4Low beam bulb
5High beam bulb
6Bulb socket for parking and standing
lamp
Low and high beam bulb
Switch off the lights.
Open the hood (
page 234).
Press the clamp and remove headlamp
cover2 or 3.
Pull electrical connector off.
Unclip the retainer springs and take out
the bulb.
Insert the new bulb so that the base
locates in the recess on the holder.
Clip the retainer springs and plug the
connector onto the bulb.
Align headlamp cover2 or 3 and click
into place.
Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 234).
Twist bulb socket1 counterclockwise
and pull out.
Push bulb into socket, turn counter-
clockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinsert bulb socket in lamp and twist
clockwise.
S203 MY03_A.book Page 294 Tuesday, January 28, 2003 2:22 PM
Page 289 of 370
295 Practical hints
Replacing bulbs
Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 234).
Press the clamp and remove headlamp
cover2.
Pull out the bulb socket6 with the
bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Align headlamp cover2 and click into
place.Bi-Xenon* headlamps
1Bulb socket for turn signal lamp
2Headlamp cover for high beam bulb,
parking and standing lamp
3Headlamp cover for Bi-Xenon lamp4High beam headlamp bulb
5Bayonet socket for high beam head-
lamp bulb
6Bulb socket for parking and standing
lamp
High beam bulb
Switch off the lights.
Open the hood (
page 234).
Press the clamp and remove headlamp
cover2.
Pull electrical connector4 off.
Warning!
G
Do not remove the cover3 for the Bi-Xenon
headlamp. Because of high voltage in
Bi-Xenon lamps, it is dangerous to replace
the bulb or repair the lamp and its compo-
nents. We recommend that you have such
work done by a qualified technician.
S203 MY03_A.book Page 295 Tuesday, January 28, 2003 2:22 PM
Page 290 of 370
296 Practical hintsReplacing bulbs
Twist bayonet socket5 counterclock-
wise to the stop (do not remove).
Pull the bulb out of the socket.
Insert the new bulb so that the base lo-
cates in the recess in the bayonet
socket5.
Twist bayonet socket clockwise until
you hear it snap into place.
Plug the connector onto the bulb.
Align headlamp cover2 and click into
place.Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 234).
Twist bulb socket1 counterclockwise
and pull out.
Push bulb into socket, turn counter-
clockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinsert bulb socket in lamp and twist
clockwise.Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 234).
Press the clamp and remove headlamp
cover2.
Pull out the bulb socket6 with the
bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Align headlamp cover2 and click into
place.
S203 MY03_A.book Page 296 Tuesday, January 28, 2003 2:22 PM
Page 291 of 370
297 Practical hints
Replacing bulbs
Side marker lamp bulb
Switch off the lights.
Carefully slide lamp towards rear.
Remove front end first.
Twist bulb socket counterclockwise
and pull out.
Pull bulb out of the bulb socket.
Insert new bulb in socket.
Reinstall bulb socket, push in and twist
clockwise.
To reinstall lamp, set rear end in
bumper and let front end snap into
place.
Replacing bulbs for rear lamps
Tail lamp assemblies
Open tailgate (
page 87).
Switch off the lights.
Press button1 on the corresponding
side.
Fold down trim panel2.
Squeeze tabs together3.
Remove bulb holder.
S203 MY03_A.book Page 297 Tuesday, January 28, 2003 2:22 PM
