Page 264 of 356
264 Practical hintsWhat to do if …Display
Possible cause
Suggested solution
.
LOW BEAM, L
CHECK LAMP!
The left low beam lamp is malfunctioning.
Visit an authorized Mercedes-Benz
Center as soon as possible.
LOW BEAM, R
CHECK LAMP!
The right low beam lamp is malfunctioning.
Visit an authorized Mercedes-Benz
Center as soon as possible.
DISPLAY DEFECTIVE
VISIT WORKSHOP!
The display for the lamps or the system is
malfunctioning.
Visit an authorized Mercedes-Benz
Center as soon as possible.
TURN SIGNAL, LR
CHECK LAMP!
The left rear turn signal lamp is malfunc-
tioning.
Replace the bulb as soon as possible.
TURN SIGNAL, RR
CHECK LAMP!
The right rear turn signal lamp is malfunc-
tioning.
Replace the bulb as soon as possible.
TURN SIG. IN MIRROR, L
CHECK LAMP!
The left turn signal in the side mirror is mal-
functioning. This message will only appear
if all light emitting diodes have stopped
working.
Have the LEDs replaced as soon as
possible.
TURN SIG. IN MIRROR, R
CHECK LAMP!
The right turn signal in the side mirror is
malfunctioning. This message will only ap-
pear if all light emitting diodes have
stopped working.
Have the LEDs replaced as soon as
possible.
Page 267 of 356
267
Practical hints
What to do if …
Display
Possible cause
Suggested solution
.
TAIL LAMP, R
CHECK LAMP!
SUBSTITUTE LAMP ON!
The right tail lamp is malfunctioning. A
backup bulb is being used.
Visit an authorized Mercedes-Benz
Center as soon as possible.
SIDE MARKER LAMP, LF
CHECK LAMP!
SUBSTITUTE LAMP ON!
The left side marker lamp is malfunction-
ing. A backup bulb is being used.
Visit an authorized Mercedes-Benz
Center as soon as possible.
SIDE MARKER LAMP, RF
CHECK LAMP!
SUBSTITUTE LAMP ON!
The right side marker lamp is malfunction-
ing. A backup bulb is being used.
Visit an authorized Mercedes-Benz
Center as soon as possible.
LIGHTS
TURN OFF LAMPS!
This display appears if the driver’s door is
opened with the engine shut off and no
key in the starter switch.
Insert key in the starter switch.
Switch off lights.
AUTOM. LIGHT ON
REMOVE KEY!
Key in the starter switch position
1 or 2.
Remove key from the starter switch.
!
(Canada only)
;
(USA only)
PARKING BRAKE
RELEASE PARKING BRAKE!
You are driving with the parking brake set.
Release the parking brake
(page 46).
<
SEAT BELT SYSTEM
VISIT WORKSHOP!
The seat belt system is malfunctioning.
Visit an authorized Mercedes-Benz
Center as soon as possible.
Page 273 of 356
273
Practical hints
Where will I find ...?
Spare wheel bolts
1 Wheel bolt for light alloy rims
2 Wheel bolt for light alloy spare wheel
rim size 4
1/2B x15 H2 Refer to “Technical data” section
(
page 313) for model and spare wheel
rim size information.
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on level surface. Make sure that the jack
arm is fully seated in the jack take-up brack-
et. Always lower the vehicle onto sufficient
capacity jack stands before working under
the vehicle.
!Wheel bolts 2 must be used when
mounting spare wheel rim
size 4
1/2Bx15 H2 (
page 313).
The use of any wheel bolts other than
wheel bolts 2 for spare wheel rim
size 4
1/2B x15 H2 can cause physical
damage to the vehicle.
Warning!
G
Be sure to use the original length wheel
bolts when remounting the original wheel af-
ter it has been repaired.
Page 278 of 356
278 Practical hintsOpening/closing in an emergency
Opening/closing in an emergencyPanorama sliding/pop-up roof
The panorama sliding/pop-up roof drive is
located behind the lens of the interior over-
head light.
You can open or close the panorama slid-
ing/pop-up roof manually should an elec-
trical malfunction occur.
Pry off lens1 using a screwdriver.
Slide both locking tabs 2 in direction of
arrow.
Lower rear of cover and remove.
Remove cover.
Obtain crank 3.
Insert crank 3 through left hand side
motor hole 4.
Turn crank 3 clockwise to:
slide roof closed
raise roof at the rear
Turn crank 3 counterclockwise to:
slide roof open
lower roof at the rear
The panorama sliding/pop-up roof must be
resynchronized after being operated man-
ually.
iDo not disconnect electrical connec-
tors.
Page 280 of 356
280 Practical hintsReplacing bulbs
Replacing bulbsSafe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See your autho-
rized Mercedes-Benz Center for headlamp
adjustment.
BulbsFront lamps
iBackup bulbs will be brought into use
when the following lamps malfunction:
Rear fog lamp
Tail lamps
Standing lamps
Lamp
Type
1
Additional turn sig-
nal lamps
LED
2
Turn signal lamp
Halogen headlamp
Turn signal lamp
Bi-Xenon* headlamp
1156A
2357A
3
Low beam Halogen
Low and hi beam*
H7 (55W)
Bi-Xenon*
4
High beam
H7 (55 W)
Parking and stand-
ing lamp
W 5 W
5
Fog lamp
HB4/9006
(55 W)
6
Side marker lamp
W 5 W
Page 281 of 356
281
Practical hints
Replacing bulbs
Rear lamps
Notes on bulb replacement
Use only 12-volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Your hands should be dry and free of oil
and grease.
If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Center.
Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Center.
Additional turn signals in the exteri-
or rear view mirrors
High mounted brake lamp
Xenon lamps
Front fog lamps
Lamp
Type
7
High mounted brake
lamp
LED
8
License plate lamps
C5W
9
Brake lamp
P 21 W (21W)
Turn signal lamp
PY21W (21W)
Tail, parking stand-
ing and side marker
lamp
W5W (5W)
Rear fog lamp, driv-
er’s side
P21W (21W)
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you
touch or move it when hot
drop the bulb
scratch the bulb
Wear eye and hand protection.
Because of high voltage in xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
Page 282 of 356
282 Practical hintsReplacing bulbsReplacing bulbs for front lamps
Halogen headlamps1 Bulb socket for turn signal lamp
2 Headlamp cover for high beam head-
lamp and for parking and standing
lamp
3 Headlamp cover for low beam head-
lamp 4
Low beam bulb
5 High beam bulb
6 Parking and standing lamp
Low and high beam bulb
Switch off the lights.
Open the hood (
page 226).
Turn headlamp cover 2 or 3 to the left
and remove.
Turn bulb holder with bulb to the left
and pull out.
Pull out the bulb from the base (do not
pull on glass tube).
Insert new bulb so that the base fits in
the bulb holder recess and is level.
Place the bulb holder with bulb on the
headlamp mounting and turn the bulb
holder to the righ t until it engages.
Replace headlamp cover 2 or 3 and
turn to the right until it engages.
Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 226).
Turn bulb socket 1 to the left and pull
out.
Push bulb into socket, turn to the left
and remove.
Insert new bulb in socket, push in and
turn to the right.
Reinsert bulb socket in lamp and turn
to the right.
Page 283 of 356
283
Practical hints
Replacing bulbs
Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 226).
Turn headlamp cover
2 to the left and
remove.
Pull out the bulb socket with the bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Replace headlamp cover 2 and turn to
the right until it engages. Bi-Xenon* headlamps
1 Bulb socket for turn signal lamp
2 Headlamp cover for high beam head-
lamp 3
Headlamp cover for Bi-Xenon head-
lamp
4 High beam bulb
5 Bulb holder
6 Parking and standing lamp
High beam bulb
Switch off the lights.
Open the hood (
page 226).
Turn headlamp cover 2 to the left and
remove.
iIf the inside of the headlamps is fogged
up, switch the lights on for a sufficient
amount of time.
Warning!
G
Do not remove the cover 3 for the Bi-Xenon
headlamp. Because of high voltage in Bi-Xe-
non lamps, it is dangerous to replace the
bulb or repair the lamp and its components.
We recommend that you have such work
done by a qualified technician.
