2003 Hyundai H-1 (Grand Starex) engine coolant

INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS
2-6
C090A01P-1
C090A01P-GAT
WATER TEMPERATURE GAUGE
WATER TEMPERATURE GAUGE WATER TEMPERATURE GAUGE
WATER TEMPERATURE GAUGE
WATER TEMPERATURE GAUGE
The water temperature gauge indicates the
engine coolant temperature. If the indication needle enters the red zone while the engine isrunning, it probably indicates that the engine isoverheated. While driving, care should alwaysbe taken to maintain the normal operating tem-perature. C100A01P-GAT
INCLINOMETER (If installed)
INCLINOMETER (If installed) INCLINOMETER (If installed)
INCLINOMETER (If installed)
INCLINOMETER (If installed)C100A01P-GAG
This meter indicates the inclination angle of the vehicle, both front-to-rear and side to side.
1. Side-to-side inclination (Right inclination of 15°)
C100A02P-GAG
2. Front-to rear inclination (Rear inclination of20°)
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
The inclinometer indicates the correct incli-
The inclinometer indicates the correct incli- The inclinometer indicates the correct incli-
The inclinometer indicates the correct incli-
The inclinometer indicates the correct incli-
nation when the vehicle is stationary, but a
nation when the vehicle is stationary, but a nation when the vehicle is stationary, but a
nation when the vehicle is stationary, but a
nation when the vehicle is stationary, but a
slight reading error may be given when driv-
slight reading error may be given when driv- slight reading error may be given when driv-
slight reading error may be given when driv-
slight reading error may be given when driv-
ing the vehicle.
ing the vehicle. ing the vehicle.
ing the vehicle.
ing the vehicle.

STARTING & OPERATING
STARTING & OPERATING STARTING & OPERATING
STARTING & OPERATING
STARTING & OPERATING
3-16 D180H01P-GAT
Parking brake
Parking brake Parking brake
Parking brake
Parking brake
If the atmospheric temperature is below freez- ing, park the vehicle with the gearshift lever in1st or reverse and do not engage the parkingbrake. If the parking brake is engaged and thereis moisture on the brake linings, the liningscould become frozen to the brake drums, mak-ing it impossible to release the parking brake.
C160G02A-AAT
To Keep Locks from Freezing
To Keep Locks from Freezing To Keep Locks from Freezing
To Keep Locks from Freezing
To Keep Locks from Freezing
To keep the locks from freezing, squirt anapproved de-icer fluid or glycerine into the keyopening. If a lock is covered with ice, squirt itwith an approved de-icing fluid to remove theice. If the lock is frozen internally, you may beable to thaw it out by using a heated key.Handle the heated key with care to avoid burn-ing your fingers.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
The proper temperature for using the immo-
The proper temperature for using the immo- The proper temperature for using the immo-
The proper temperature for using the immo-
The proper temperature for using the immo-
bilizer key is from -40°C to 80°C. If you heat
bilizer key is from -40°C to 80°C. If you heat bilizer key is from -40°C to 80°C. If you heat
bilizer key is from -40°C to 80°C. If you heat
bilizer key is from -40°C to 80°C. If you heat
the immobilizer key over 80°C to open the
the immobilizer key over 80°C to open the the immobilizer key over 80°C to open the
the immobilizer key over 80°C to open the
the immobilizer key over 80°C to open the
frozen lock, it may cause damage to the
frozen lock, it may cause damage to the frozen lock, it may cause damage to the
frozen lock, it may cause damage to the
frozen lock, it may cause damage to the
transponder in its head.
transponder in its head. transponder in its head.
transponder in its head.
transponder in its head. D180G01P-GAT
Door locks
Door locks Door locks
Door locks
Door locks
To prevent the door locks from freezing up, the lock cylinders should be masked with tape,etc., when washing the vehicle in cold weatherto prevent the entrance of water.
D180E01P-GAT
Wiper blades
Wiper blades Wiper blades
Wiper blades
Wiper blades
Before operating the wipers, check the wiperblades to confirm that they are not frozen to thewindshield or tailgate. If the blades are frozen tothe windshield or tailgate, do not operate thewipers until the ice has melted and the bladesare freed. D180F01P-GAT
Ventilation slots
Ventilation slots Ventilation slots
Ventilation slots
Ventilation slots
The ventilation slots in the headlight housing on the assistant seat side should be brushed clearafter a heavy snowfall so that the operation ofthe heating and ventilation systems will not beimpaired.
anyway, will only deliver a fraction of the startercurrent which is normally available. It is recommended that you have the battery checked by an authorized HYUNDAI dealerbefore the start of cold weather and, if neces-sary, have it charged. This not only ensures reliable starting, but a battery which is kept fully charged also has alonger life. D180D01P-GAT
Washer fluid
Washer fluid Washer fluid
Washer fluid
Washer fluid
To ensure proper operation of the windshield or rear window at low temperatures, anti-freezeshould be added to the washer fluid at a rate ofone part antifreeze to one part water.
D180A01P-GAT
DURING COLD WEATHER
DURING COLD WEATHER DURING COLD WEATHER
DURING COLD WEATHER
DURING COLD WEATHER
Engine oil
Engine oil Engine oil
Engine oil
Engine oil
The engine oil can become very thick at low
temperatures, thus making it difficult to start theengine.
Change to a thinner oil designed for winter use
before the start of cold weather; for the appro-priate oil viscosity, refer to the "Consumer Infor-mation" section.
D180B01P-GATEngine coolant
Engine coolant Engine coolant
Engine coolant
Engine coolant
If the temperature in your area drops below
freezing, there is the danger that the coolant inthe engine or radiator could freeze and causesevere damage to the engine and/or radiator. Be sure to add a sufficient amount of antifreeze
to the coolant to prevent it from freezing.
The engine coolant mixture used at the factory
is intended to be left in the cooling system andprovides protection against freezing for tem-perature as low as approximately -30°C (-20°F).The concentration should be checked beforethe start of cold weather and anti-freeze addedto the system if necessary
D180C01P-GATBattery
Battery Battery
Battery
Battery
The capacity of the battery is reduced at low
temperatutes.
This is an inevitable result of its chemical and
physical properties. This is why a very coldbattery, particularly one that is not fully charged

IN CASE OF EMERGENCY
IN CASE OF EMERGENCY IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
4-9
C190E04P-GAT
Trailer Weight Limit
Trailer Weight Limit Trailer Weight Limit
Trailer Weight Limit
Trailer Weight Limit
SSA2200BTongue load Total trailer weight
Tongue loads can be increased or decreased by redistributing the load in the trailer. This canbe verified by checking the total weight of theloaded trailer and then checking the load on thetongue.
SSA2200D
Gross axle weight Gross vehicle weight
C190B01S-AAT
Trailer Hitches
Trailer Hitches Trailer Hitches
Trailer Hitches
Trailer Hitches
Select the proper hitch and ball combination,
making sure that its location is compatible with that of the trailer or vehicle being towed. Use aquality non-equalizing hitch which distributesthe tongue load uniformly throughout the chas-sis.
The hitch should be bolted securely to the car
and installed by a qualified technician. DO NOTUSE A HITCH DESIGNED FOR TEMPORARYINSTALLATION AND NEVER USE ONE THATATTACHES ONLY TO THE BUMPER.
C190C01P-GATTrailer Brakes
Trailer Brakes Trailer Brakes
Trailer Brakes
Trailer Brakes
If your trailer is equipped with a braking system,make sure it conforms to federal and/or localregulations and that it is properly installed andoperating correctly.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
If you tow a trailer or vehicle, your car will
If you tow a trailer or vehicle, your car will If you tow a trailer or vehicle, your car will
If you tow a trailer or vehicle, your car will
If you tow a trailer or vehicle, your car will
require more frequent maintenance due to
require more frequent maintenance due to require more frequent maintenance due to
require more frequent maintenance due to
require more frequent maintenance due to
the additional load. See "Maintenance Un-
the additional load. See "Maintenance Un- the additional load. See "Maintenance Un-
the additional load. See "Maintenance Un-
the additional load. See "Maintenance Un-
der Severe Usage Conditions" on page 6-8.
der Severe Usage Conditions" on page 6-8. der Severe Usage Conditions" on page 6-8.
der Severe Usage Conditions" on page 6-8.
der Severe Usage Conditions" on page 6-8. C190D01A-GAT
Safety Chains
Safety Chains Safety Chains
Safety Chains
Safety Chains
Should the hitch connection between your car
and the trailer or vehicle you are towing fail, thetrailer or vehicle could wander dangerouslyacross other lanes of traffic and ultimately col-lide with another vehicle.
To eliminate this potentially dangerous situa-
tion, safety chains, attached between your carand the trailer or towed vehicle, are required inmost provinces.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Do not do any towing with your car during
Do not do any towing with your car during Do not do any towing with your car during
Do not do any towing with your car during
Do not do any towing with your car during its first 2,000 km (1,200 miles) in order to
its first 2,000 km (1,200 miles) in order to its first 2,000 km (1,200 miles) in order to
its first 2,000 km (1,200 miles) in order to
its first 2,000 km (1,200 miles) in order to
allow the engine to properly break in. Fail-
allow the engine to properly break in. Fail- allow the engine to properly break in. Fail-
allow the engine to properly break in. Fail-
allow the engine to properly break in. Fail-
ure to heed this caution may result in seri-
ure to heed this caution may result in seri- ure to heed this caution may result in seri-
ure to heed this caution may result in seri-
ure to heed this caution may result in seri-
ous engine or transmission damage.
ous engine or transmission damage. ous engine or transmission damage.
ous engine or transmission damage.
ous engine or transmission damage. CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
oo
oo
o
Never connect a trailer brake system di-
Never connect a trailer brake system di- Never connect a trailer brake system di-
Never connect a trailer brake system di-
Never connect a trailer brake system di-
rectly to the vehicle brake system.
rectly to the vehicle brake system. rectly to the vehicle brake system.
rectly to the vehicle brake system.
rectly to the vehicle brake system.
oo
oo
o When towing a trailer on steep grades (in
When towing a trailer on steep grades (in When towing a trailer on steep grades (in
When towing a trailer on steep grades (in
When towing a trailer on steep grades (in
excess of 12%) pay close attention to the
excess of 12%) pay close attention to the excess of 12%) pay close attention to the
excess of 12%) pay close attention to the
excess of 12%) pay close attention to the
engine coolant temperature gauge to
engine coolant temperature gauge to engine coolant temperature gauge to
engine coolant temperature gauge to
engine coolant temperature gauge to
ensure the engine does not overheat. If
ensure the engine does not overheat. If ensure the engine does not overheat. If
ensure the engine does not overheat. If
ensure the engine does not overheat. If
the needle of the coolant temperature
the needle of the coolant temperature the needle of the coolant temperature
the needle of the coolant temperature
the needle of the coolant temperature
gauge moves across the dial towards
gauge moves across the dial towards gauge moves across the dial towards
gauge moves across the dial towards
gauge moves across the dial towards
"H" (HOT), pull over and stop as soon as
"H" (HOT), pull over and stop as soon as "H" (HOT), pull over and stop as soon as
"H" (HOT), pull over and stop as soon as
"H" (HOT), pull over and stop as soon as
it is safe to do so, and allow the engine to
it is safe to do so, and allow the engine to it is safe to do so, and allow the engine to
it is safe to do so, and allow the engine to
it is safe to do so, and allow the engine to
idle until it cools down. You may proceed
idle until it cools down. You may proceed idle until it cools down. You may proceed
idle until it cools down. You may proceed
idle until it cools down. You may proceed
once the engine has cooled sufficiently.
once the engine has cooled sufficiently. once the engine has cooled sufficiently.
once the engine has cooled sufficiently.
once the engine has cooled sufficiently.

IN CASE OF EMERGENCY
IN CASE OF EMERGENCY IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
4-12 normal for cold water to be draining from it when you stop).
WARNING:
WARNING: WARNING:
WARNING:
WARNING:
While the engine is running, keep hair, hands,
While the engine is running, keep hair, hands, While the engine is running, keep hair, hands,
While the engine is running, keep hair, hands,
While the engine is running, keep hair, hands,
long hair and
long hair and long hair and
long hair and
long hair and clothing away from moving
clothing away from moving clothing away from moving
clothing away from moving
clothing away from moving
parts such as the fan and drive belts to
parts such as the fan and drive belts to parts such as the fan and drive belts to
parts such as the fan and drive belts to
parts such as the fan and drive belts to
prevent
prevent prevent
prevent
prevent injury.
injury. injury.
injury.
injury.
5. If the water pump drive belt is broken or engine coolant is leaking out, stop the en-gine immediately and call the nearestHyundai dealer for assistance.
WARNING:
WARNING: WARNING:
WARNING:
WARNING:
Do not remove the radiator cap when the
Do not remove the radiator cap when the Do not remove the radiator cap when the
Do not remove the radiator cap when the
Do not remove the radiator cap when the
engine is hot. This
engine is hot. This engine is hot. This
engine is hot. This
engine is hot. This can allow coolant to be
can allow coolant to be can allow coolant to be
can allow coolant to be
can allow coolant to be
blown out of the opening and cause serious
blown out of the opening and cause serious blown out of the opening and cause serious
blown out of the opening and cause serious
blown out of the opening and cause serious
burns.
burns. burns.
burns.
burns.
GS40280A
6. If you cannot find the cause of the overheat-
ing, wait until the engine temperature has returned to normal. Then, if engine coolant
has been lost, carefully remove the radiator
cap and add engine coolant to bring the fluidlevel in the reservoir up to the halfway mark.
7. Proceed with caution, keeping alert for fur- ther signs of overheating. If overheating hap-pens again, call a Hyundai dealer for assis-tance.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Serious loss of engine coolant indicates
Serious loss of engine coolant indicates Serious loss of engine coolant indicates
Serious loss of engine coolant indicates
Serious loss of engine coolant indicates
there is a leak in
there is a leak in there is a leak in
there is a leak in
there is a leak in the cooling system and this
the cooling system and this the cooling system and this
the cooling system and this
the cooling system and this
should be checked as soon as possible by a
should be checked as soon as possible by a should be checked as soon as possible by a
should be checked as soon as possible by a
should be checked as soon as possible by a
Hyundai
Hyundai Hyundai
Hyundai
Hyundai dealer.
dealer. dealer.
dealer.
dealer.
GS40270A
3. If engine coolant is running out under the car
or steam is coming out from the hood, stop the engine. Do not open the hood until theengine coolant has stopped running or thesteaming has stopped. If there is no visibleloss of engine coolant and no steam, leavethe engine running and check to be sure theengine cooling fan is operating. If the fan isnot running, turn the engine off.
4. Check to see if the water pump drive belt is missing. If it is not missing, check to seethat it is tight. If the drive belt seems to besatisfactory, check for engine coolant leak-ing from the radiator, hoses or under the car.(If the air conditioning had been in use, it is
1. Pull off the road and stop as soon as it is
safe to do so.
2. Place the gear selector lever in "P" (auto- matic), or neutral (manual transmission) andset the parking brake. If the air conditioning
is on, turn it off.

IN CASE OF EMERGENCY
IN CASE OF EMERGENCY IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
4-17
1) Horizontal line dimension from ground
MINIBUS 2WD:849 mm (33.43 in.) 4WD:972 mm (38.27 in.)
VAN(2WD) : 855 mm (33.66 in.)
TRUCK Long Wheel base
:847 mm (33.35 in.)Extra long Wheel base:845 mm (33.27 in.)
2) Distance between each vertical line.
MINIBUS/VAN(2WD/4WD):1300mm (51.18 in.)
TRUCK (Long wheel base/Extra long
wheel base) : 1272 mm (50.08 in.)
3) Distance between the headlights and the wall that the lights are tested against: 3000 mm (118.11 in)
And then, draw the parallel line at 30 mm (1.18 in.) place under the horizontal line.
7. Adjust each cut-off line of the low beam to the parallel line with a phillips screwdriver - VERTICAL AIMING
8. Adjust each cut-off line of the low beam to the each vertical line with a phillips screw- driver - HORIZONTAL AIMING.
G290A03P-AATHEADLIGHT AIMING ADJUSTMENT
HEADLIGHT AIMING ADJUSTMENT HEADLIGHT AIMING ADJUSTMENT
HEADLIGHT AIMING ADJUSTMENT
HEADLIGHT AIMING ADJUSTMENT
G290A01P-1
Before performing aiming adjustment, make sure of the following.
1. Keep all tires inflated to the correct pres- sure.
2. Place the vehicle on level ground and press the front bumper & rear bumper down sev-eral times.
3. See that the vehicle is unloaded (except for full levels of coolant, engine oil and fuel, andspare tire, jack, and tools).
4. Clean the head lights lens and turn on the headlight (Low beam).
5. Open the hood.
6. Draw the vertical line (through the center of each headlight) and the horizontal line (through the center of each headlight) on theaiming screen.
Horizontalaiming
Verticalaiming
G270A01S-AAT
HEADLIGHT BULB
HEADLIGHT BULB HEADLIGHT BULB
HEADLIGHT BULB
HEADLIGHT BULB
Replacement instructions:
Replacement instructions: Replacement instructions:
Replacement instructions:
Replacement instructions:
1. Allow the bulb to cool. Wear eye protection.
2. Always grasp the bulb by its plastic base,
avoid touching the glass.
3. Disconnect the power cord from the bulb base in the back of the headlight.
4. Push the bulb spring for removing the head- light bulb.
5. Remove the protective cap from the re- placement bulb and install the new bulb by matching the plastic base with the headlighthole. Retighten the bulb spring and recon-nect the power cord.
6. Use the protective cap and carton to dis- pose of the old bulb.
7. Check for proper headlight aim.
WARNING
WARNING WARNING
WARNING
WARNING
This halogen bulb contains gas under pres-
This halogen bulb contains gas under pres- This halogen bulb contains gas under pres-
This halogen bulb contains gas under pres-
This halogen bulb contains gas under pres- sure and if impacted could shatter, resulting
sure and if impacted could shatter, resulting sure and if impacted could shatter, resulting
sure and if impacted could shatter, resulting
sure and if impacted could shatter, resulting
in flying fragments. Always wear eye pro-
in flying fragments. Always wear eye pro- in flying fragments. Always wear eye pro-
in flying fragments. Always wear eye pro-
in flying fragments. Always wear eye pro-
tection when servicing the bulb. Protect the
tection when servicing the bulb. Protect the tection when servicing the bulb. Protect the
tection when servicing the bulb. Protect the
tection when servicing the bulb. Protect the
bulb against abrasions or scratches and
bulb against abrasions or scratches and bulb against abrasions or scratches and
bulb against abrasions or scratches and
bulb against abrasions or scratches and
against liquids when lighted. Turn on the
against liquids when lighted. Turn on the against liquids when lighted. Turn on the
against liquids when lighted. Turn on the
against liquids when lighted. Turn on the
bulb only when installed in a headlight. Re-
bulb only when installed in a headlight. Re- bulb only when installed in a headlight. Re-
bulb only when installed in a headlight. Re-
bulb only when installed in a headlight. Re-
place the headlight if damaged or cracked.
place the headlight if damaged or cracked. place the headlight if damaged or cracked.
place the headlight if damaged or cracked.
place the headlight if damaged or cracked.
Keep the bulb out of the reach of children
Keep the bulb out of the reach of children Keep the bulb out of the reach of children
Keep the bulb out of the reach of children
Keep the bulb out of the reach of children
and dispose of the used bulb with care.
and dispose of the used bulb with care. and dispose of the used bulb with care.
and dispose of the used bulb with care.
and dispose of the used bulb with care.

6-3
PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
DESCRIPTION
GENERAL MAINTENANCE ENGINE COOLANT *1 MANUAL TRANSMISSION OILAUTOMATIC TRANSMISSION OILTRANSFER CASE OIL *2REAR AXLE OILCLUTCH / BRAKE PEDAL FREE PLAY CLUTCH / BRAKE OIL RESERVOIR BRAKE HYDRAULIC FLUIDFRONT BRAKE PADSFRONT BRAKE CALIPERS / CYLINDERS / DISCREAR BRAKE DRUMS / LININGS / CYLINDERSHANDBRAKETIRE CONDITION / PRESSURE EXHAUST SYSTEM / MOUNTING STEERING JOINT / RACK / BOX OIL LEAKSSUSPENSION JOINT / SEALSFRONT WHEEL BEARINGENGINE COOLANT HOSESBRAKE PIPE CORROSION SEATBELTS / MOUNTINGS HEAD LAMPSAIR FILTER (For Evaporator and Blower unit) *3
NO.
123456 7 89
10111213 14 1516171819 20 2122
G030A04P-GAT R : REPLACE I : INSPECT AND, AFTER INSPECTION, CLEAN, ADJUST, REPAIR OR REPLACE IF NECESSARY
70 56
I I I I I I III I I 80 64
I I
R II I IIII I I IIII I90 72
I I I III I I I I I II
20 16
I I I II I IIIII I IIII I 30 24
I I I III I III I II 40 32
I I
R II I III I I IIIII I 50 40
I I I I I I III I I 60 48
I I I IIIII I I I I IIIIIII
See below
KILOMETERS X 1000 MONTHS
54
R 10
8
I I I I I I III I I
See below
*1. For every 24 months or 40,000 km, whichever occurs first : "R"
*2. For every 24 months or 48,000 km, whichever occurs first : "R"
*3. For every 12 months or 20,000 km, whichever occurs first : "R" See below

6-7
PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
DESCRIPTION
GENERAL MAINTENANCE ENGINE COOLANT *1 MANUAL TRANSMISSION OIL AUTOMATIC TRANSMISSION OIL TRANSFER CASE OIL *2 REAR AXLE OIL CLUTCH/BRAKE PEDAL FREEPLAY CLUTCH/BRAKE OIL RESERVOIR BRAKE HYDRAULIC FLUID FRONT BRAKE PAD FRONT BRAKE CALIPERS/CYLINDERS/DISC REAR BRAKE DRUMS/LININGS/CYLINDERS HAND BRAKE TIRE CONDITION/PRESSURE EXHAUST SYSTEM/MOUNTING STEERING JOINT/RACK/BOX/OIL LEAKS SUSPENSION JOINT/SEALS FRONT WHEEL BEARING ENGINE COOLANT HOSES BRAKE PIPE CORROSION
AIR FILTER (F o r Evapoerator and Blower unit) *3
NO.
12 3 4 5 6 7 8 9
1011 12 13 14 15 16 17 18 19 20KILOMETERS X 1000 MONTH90 72
I
R R I I I I I I I I I I I I I I
G060A04P-GAT R : REPLACE I : INSPECT AND, AFTER INSPECTION, CLEAN, ADJUST, REPAIR OR REPLACE IF NECESSARY15 12
II I I I I I I I 30 24
II I I I I I I I I I I I I I I I 4536
II
R II I I I I 60 48
II I I I I I I I I I I I I I I I 7560
II I I I I I I I7.5 6
R
See below See below
*1. For every 24 months or 45,000 km, whichever occurs first : "R" *2. For every 24 months or 48,000 km, whichever occurs first : "R"*3. For every 12 months or 20,000 km, whichever occurs first : "R"
See below

PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
6-10 G080N01P-GAT
oo
oo
o Brake hoses and lines
Brake hoses and lines Brake hoses and lines
Brake hoses and lines
Brake hoses and lines
Visually check for proper installation, chafing, cracks, deterioration and any leakage. Replaceany deteriorated or damaged parts immedi-ately. G080O01P-GAT
oo
oo
o Brake fluid
Brake fluid Brake fluid
Brake fluid
Brake fluid
Check brake fluid level in the brake fluid reser- voir. The level should be between "MIN" and"MAX" marks on the side of the reservoir. Useonly hydraulic brake fluid conforming SAEJ1703. G080P01P-GAT
oo
oo
o Rear brake drums and linings
Rear brake drums and linings Rear brake drums and linings
Rear brake drums and linings
Rear brake drums and linings
Check for scoring, burning, leaking fluid, bro- ken parts, and excessive wear. G080Q01P-GAT
oo
oo
o Brake pads, calipers and rotors
Brake pads, calipers and rotors Brake pads, calipers and rotors
Brake pads, calipers and rotors
Brake pads, calipers and rotors
Check the pads for excessive wear, discs for run out and wear, and calipers for fluid leakage. G080R01P-GAT
oo
oo
o
Parking brake
Parking brake Parking brake
Parking brake
Parking brake
Inspect the parking brake system such as parking brake lever, cables, and so on. Fordetailed service procedures, refer to the ShopManual. G080S01P-GAT
oo
oo
o
Exhaust pipe connections,
Exhaust pipe connections, Exhaust pipe connections,
Exhaust pipe connections,
Exhaust pipe connections,
muffler and suspension bolts
muffler and suspension bolts muffler and suspension bolts
muffler and suspension bolts
muffler and suspension bolts
Check the exhaust pipe, muffler, and suspen-sion connections for looseness or damage. G080T01P-GAT
oo
oo
o
Steering gear box, linkage and boots
Steering gear box, linkage and boots Steering gear box, linkage and boots
Steering gear box, linkage and boots
Steering gear box, linkage and boots
With the vehicle stopped and engine off, check for excessive free-play in the steering wheel.Check the linkage for bends or damage. Checkthe dust boots and ball joints for deterioration,cracks, or damage. Replace any damaged parts. G080U01P-GAT
oo
oo
o Wheel bearing grease
Wheel bearing grease Wheel bearing grease
Wheel bearing grease
Wheel bearing grease
Check the wheel bearings and grease accord- ing to the maintenance schedule. For inspec-tion procedures, see Shop Manual.
G080J01P-GAT
oo
oo
o Engine coolant
Engine coolant Engine coolant
Engine coolant
Engine coolant
The coolant should be changed at those inter-
vals specified in the Vehicle Maintenance Re-quirements Section.
G080K01P-GAT oo
oo
o
Timing belt
Timing belt Timing belt
Timing belt
Timing belt
Inspect all parts related with the timing belt for
damage and deformation. Replace any dam-aged parts.
G080L01P-GAT oo
oo
o Manual transmission oil
Manual transmission oil Manual transmission oil
Manual transmission oil
Manual transmission oil
Check manual transaxle oil according to the
maintenance schedule.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
If the oil level is low, check for possible
If the oil level is low, check for possible If the oil level is low, check for possible
If the oil level is low, check for possible
If the oil level is low, check for possible leaks before adding oil. Do not overfill.
leaks before adding oil. Do not overfill. leaks before adding oil. Do not overfill.
leaks before adding oil. Do not overfill.
leaks before adding oil. Do not overfill.
G080M02P-GAT oo
oo
o
Automatic transmission fluid
Automatic transmission fluid Automatic transmission fluid
Automatic transmission fluid
Automatic transmission fluid
The fluid level should be in the "HOT" range of
the dipstick, after engine and transaxle are at normal operating temperature. Check the Auto-matic Transaxle Fluid level with the enginerunning and the transaxle in neutral, with theparking brake properly applied. Use GENUINEHYUNDAI ATF AUTOMATIC TRANSMISSIONFLUID, DIAMOND ATF DEXRON II or DIA-
MOND ATF SP I when adding or changing
fluid.