2003 Hyundai Coupe ignition

CONTROLS AND EQUIPMENT
1- 4
HGK099-D
B040G01GK-GAT Central Door Lock The central door locking is operated by pushing the driver's door lock switch toward the front orrear of the vehicle. If the passenger door is openwhen the switch is pushed, the door will remainlocked when closed. NOTE:
o When pushing the switch toward the rear, all doors will unlock.When pushing the switch toward the front,all doors will lock.
o When the door is unlocked, the red mark on the switch is visible.
o The central door locking is operated by turning the key (driver's door only) towardthe front or rear of the vehicle. B070A01A-AAT THEFT-ALARM SYSTEM (Not all models) This system is designed to provide protection from unauthorized entry into the car. This systemis operated in three stages: the first is the "Armed"stage, the second is the "Alarm" stage, and thethird is the "Disarmed" stage. If triggered, thesystem provides an audible alarm with blinkingof the turn signal light.
B070C01GK-EAT Alarm StageThe alarm will be activated if any of the following occur while the car is parked and the system isarmed.
1) A front door is unlocked and opened withoutusing the transmitter.
2) The hatchback door is opened without using the key.
3) The engine bonnet is opened.The siren will sound and the turn signal lamp will blink continuously for 30 seconds. To turn off thesystem, unlock the door with the transmitter. CAUTION: Avoid trying to start the engine while thesystem is armed.
B070B02GK-EAT Armed Stage Park the car and stop the engine. Arm the system as described below.
1) Remove the ignition key from the ignition
switch.
2) Make sure that the engine bonnet and hatch- back door are closed.
3) Lock the doors using the transmitter of the keyless entry system.
After completion of the steps above, the turn signal lamp will blink once to indicate that thesystem is armed. NOTE:
1) If any door, hatchback door or engine bonnet remains open, the system will notbe armed.
2) If this happens, rearm the system as de- scribed above. 3) Once the system is armed, only the hatch-
back door may be unlocked using the keywithout disarming the system.
CAUTION:Do not arm the system until all passengershave left the car. If the system is armed whilea passenger(s) remains in the car, the alarmmay be activated when the remainingpassenger(s) leaves the car.

CONTROLS AND EQUIPMENT
1- 6 B050A01GK-AAT DOOR WINDOWS Power window (Not all models)
HGK096-D(1)
HGK097-D
The power windows operate only when the igni- tion key is in the "ON" position. The main switchesare located on the driver's arm rest and controlthe front windows on the respective sides of thevehicle. The windows may be opened by de-pressing the front portion of the switch. To stop atthe desired opening, release the switch. Thewindow may be closed by pulling the front portionof the switch. In order to prevent operation of thepassenger front window by passenger, a windowlock switch (1) is provided on the arm rest of thedriver's door. To disable the passenger's powerwindow, push the window lock switch. To revertto normal operation, push in on the window lockswitch again.
CAUTION:Never try to operate the main switch and sub-switch in opposing directions at the sametime. If this is done, the window will stop andcannot be opened or closed. Auto-Down Window (Driver's Side) (Not all models) The Auto-Down window is moved to its fully open position by pushing the switch, and to stop at thedesired position push in on the switch again.
2. Remove the old battery from the case and
note the polarity. Make sure the polarity of thenew battery is the same(+side facing down),then insert it in the transmitter.
NOTE: Install a new battery within 30 seconds after remove the old one, if installing a new batterytakes more than 30 seconds, take the follow-ing steps.
1) Turn the ignition key to the "ACC" posi- tion.
2) Make sure that the turn signal lights blink once by pushing the "LOCK" or "UN- LOCK" button on the transmitter.
HGK121
Battery

CONTROLS AND EQUIPMENT1- 7
SB070A1-E FRONT SEAT ADJUSTMENT WARNING: Front seat adjustments must not be under- taken whilst the vehicle is in motion. Loss ofcontrol of the vehicle may result if seat ad-justments are made whilst the vehicle is inmotion. SB070B2-E Front seat rake adjustment The front seat rake adjustment is performed by raising the lever at the front of the seat base andsliding the seat to the desired position. At thisposition the lever should be released and theseat rocked to and fro to ensure that the mecha-nism has locked.
B050A02GK-D
WARNING:
o Be careful that head, hands and body are
not trapped by a closing window.
o If passengers remain in the car when you leave, especially if a child remains alone,always remove the ignition key for theirsafety.
HGK054-D
SB070C1-E Front seat recline adjustment The front seat back recline angle may be ad- justed by leaning forward slightly and raising therecline adjustment lever at the side of the seat.When the seatback is at the desired angle, thelever should be released. Ensure that theseatback is locked before driving the vehicle.
HGK051-D
WARNING: To ensure the seat is locked securely, at-tempt to move the seat forward or rearwardwithout using the lock release lever.

CONTROLS AND EQUIPMENT1- 9
B129A01F-AAT REAR SEAT POSITIONS WARNING: This vehicle contains two rear seating posi-tions only and a seat belt for each seatingposition. Thus, never permit more than twooccupants to ride in the rear seat because anunrestrained occupant could be seriouslyinjured or killed in the event of a vehiclecrash.
B129A01GK
B100A01Y-AAT SEAT WARMER (Not all models) The seat warmer is provided to warm the front seats during cold weather. With the ignition keyin the "ON" position, push either of the switchesto warm the driver's seat or the passenger's seat.During mild weather or under conditions wherethe operation of the seat warmer is not needed,keep the switches in the "OFF" position.
HGK123
B130A01GK-DAT REAR SEAT ENTRY (Walk in device)The driver and front passenger's seatback should be tilted to enter the rear seat.
HGK053-D
(2)
(1)
By pulling up the walk in device lever (1) at the right-up side of the driver side seatback, theseatback will tilt forward. And then pull the lockrelease lever (2) up with moving the seat forward.

CONTROLS AND EQUIPMENT1- 19
B240A01GK
Driver's Airbag
B240A01GK-GAT SUPPLEMENTAL RESTRAINT (AIRBAG) SYSTEM (SRS)(Not all models) Your Hyundai is equipped with a Supplemental Restraint (Airbag) System. The indications of thesystem's presence are the letters "SRS AIRBAG" embossed on the ornament in the steeringwheel and the passenger's side front panel padabove the glove box. The Hyundai SRS consists of airbags installed under the pad covers in the center of the steeringwheel and the passenger's side front panel abovethe glove box. The purpose of the SRS is toprovide the vehicle's driver and/or the front pas-senger with additional protection than that of-fered by the seat belt system alone, in case of afrontal impact of sufficient severity.
NOTE:
o Both the driver's and front passenger's
pre-tensioner seat belts will be activatedin certain frontal collisions. The pre-tensioner seat belts can be activated aloneor, where the frontal collision is severeenough, together with the airbags.
o When the pre-tensioner seat belts are ac- tivated, a loud noise may be heard and finedust, which may appear to be smoke, maybe visible in the passenger compartment.These are normal operating conditionsand are not hazardous.
o Although it is harmless, the fine dust may cause skin irritation and should not bebreathed for prolonged periods. Wash yourhands and face thoroughly after an acci-dent in which the pre-tensioner seat beltswere activated.
CAUTION:
o The control module that activates the SRS airbag controls the pre-tensioner seat beltalso.
o If there is some function in the pre- tensioner seat belt circuit, the warninglight will illuminate even if there is nomalfunction in the SRS airbag system. Ifthe SRS airbag warning light does notilluminate or illuminates continuouslywhen the ignition key is turned to "ON", orif it remains illuminated after blinking forapproximately 6 seconds, or if it illumi-nates while the vehicle is being driven, please have an authorized Hyundai dealerinspect the pre-tensioner seat belts and orSRS airbag system as soon as possible.
WARNING:
o Pre-tensioners are designed to operate only one time. After activation, pre-tensioner seat belts must be replaced. Allseat belts, of any type, should always bereplaced after they have been worn duringa collision.
o The pre-tensioner seat belt assembly mechanisms become hot during activa-tion. Do not touch the pre-tensioner seatbelt assemblies for several minutes afterthey have been activated.
o Do not attempt to inspect or replace the pre-tensioner seat belts yourself. Thismust be done by an authorized Hyundaidealer.
o Do not strike the pre-tensioner seat belt assemblies.
o Do not attempt to service or repair the pre- tensioner seat belt system in any manner.
o Improper handling of the pre-tensioner seat belt assemblies, and failure to heedthe warnings to not strike, modify, in-spect, replace, service or repair the pre-tensioner seat belt assemblies may leadto improper operation or inadvertent acti-vation and serious injury.
o Always wear seat belts when driving or riding in a motor vehicle.

CONTROLS AND EQUIPMENT1- 21
A fully inflated airbag in combination with a prop- erly worn seat belt slows the driver's or thepassenger's forward motion, thus reducing therisk of head and chest injury.After complete inflation, the airbag immediatelystarts deflating, enabling the driver to maintainforward visibility.
Passanger's Airbag
B240B01GK-D
CAUTION: Do not install or place any accessories (drinkholder, cassette holder, sticker, etc) on thefront passenger's panel above the glove boxin the vehicle with passenger's side air bag.Such objects may become dangerous pro-jectiles and cause injury if the passenger'sside air bag inflates. Upon deployment, tear seams molded directly into the pad covers will separate under pressurefrom the expansion of the airbags. Further open-ing of the covers then allows full inflation of theairbags.
The airbag modules are located both in thecentre of the steering wheel and in the frontpassenger's panel above the glove box. Whenthe SRSCM detects a considerable impact to thefront of the vehicle, it will automatically deploy theairbags.
B240B01GK-AAT SRS Components and Functions The SRS consists of the following components: - Driver's Side Airbag Module - Passenger's Side Airbag Module- SRS Service Reminder Indicator (SRI)- SRS Control Module (SRSCM) The SRSCM continually monitors all elements while the ignition is "ON" to determine if a frontalor near-frontal impact is severe enough to re-quire airbag deployment. The SRS service reminder indicator (SRI) on the instrument panel will blink for about 6 secondsafter the ignition key is turned to the "ON" positionor after the engine is started, after which the SRIshould go out.
B240B02L-D
B240B03L-D
B240B01L-D

CONTROLS AND EQUIPMENT
1- 22
WARNING:
o When the SRS is activated, there may be a loud noise and fine dust will be releasedthroughout the vehicle. These conditionsare normal and are not hazardous. How-ever, the fine dust generated during airbagdeployment may cause skin irritation.Wash your hands and face thoroughlywith lukewarm water and a mild soap afteran accident in which the airbags weredeployed.
o The SRS can function only when the igni- tion key is in the "ON" position. If the SRSSRI does not come on or illuminatescontinuously when the ignition key isturned to "ON", or continuously remainson after flashing for about 6 seconds whenthe ignition key is turned to the "ON"position, or after the engine is started,comes on while driving, the SRS is notworking properly. If this occurs, have yourvehicle immediately inspected by yourHyundai dealer.
o Before you replace a fuse or disconnect a battery terminal, turn the ignition key tothe "LOCK" position or remove the igni-tion key. Never remove or replace the airbag related fuse(s) when the ignition keyis in the "ON" position. Failure to heed thiswarning will cause the SRS SRI to illumi-nate.
FUD1115A
CAUTION: When installing a container of liquid air fresh-ener inside a vehicle, do not place it near theinstrument cluster nor on the instrument panelpad surface. If there is any leakage from theair freshener onto these areas (instrumentcluster, instrument panel pad or air ventila-tor), it may damage these parts. If the liquidfrom the air freshener does leak onto theseareas, wash them with water immediately. Your Hyundai is equipped with a side airbag ineach front seat. The purpose of the airbag is toprovide the vehicle's driver and/or the front pas-senger with additional protection than that of-fered by the seatbelt alone. The side impactairbags are designed to deploy only during cer-tain side-impact collisions, depending on thecrash severity, angle, speed and point of impact.The air bags are not designed to deploy in all sideimpact situations. WARNING:
o The side impact airbag is supplemental to
the driver's and the passenger's seat beltsystems and is not a substitute for them.Therefore your seat belts must be worn atall times while the vehicle is in motion. Theairbags deploy only in certain side impactconditions severe enough to cause sig-nificant injury to the vehicle occupants.
B990B04Y-AAT Side Airbag (Not all models)
B990B01L.DAG

CONTROLS AND EQUIPMENT1- 23
WARNING:
o Do not install a child restraint system in
the front passenger seat position.A child restraint system must never beplaced in the front seat. The infant or childcould be severely injured by an airbagdeployment in case of an accident.
o Extreme Hazard! Do not use a rearward facing child restraint on a seat protectedby an airbag in front of it!
o Modification to SRS components or wir-ing, including the addition of any kind of badgesto the pad cover or modifications to thebody structure, can adversely affect SRSperformance and lead to possible injury.
o For cleaning the horn pad, use only a soft, dry cloth or one which has been moist-ened with plain water. Solvents or clean-ers could adversely affect the airbag coverand proper deployment of the system.
o No objects should be placed over or near the airbag module on the steering wheel,because any such object could cause harmif the vehicle is in a crash severe enoughto cause the airbag to inflate.
o If the airbag inflates, it must be replaced by an authorized Hyundai dealer.
o Do not tamper with or disconnect SRS wiring, or other components of the SRSsystem. Doing so could result in injury,due to accidental firing of the airbag or byrendering the SRS inoperative.
o For best protection from the side airbag
system and to avoid being injured by thedeploying side airbag, both front seat oc-cupants should sit in an upright positionwith the seat belt properly fastened. Thedriver's hands should be placed on thesteering wheel at the 9:00 and 3:00 o'clockpositions. The passenger's arms andhands should be placed on their laps.
o Do not use any accessory seat covers.
o Use of seat covers could prevent or re- duce the effectiveness of the system.
o Do not install any accessories on the side or near the side airbag.
o Do not use excessive force on the side of the seat.
o Do not place any objects over the airbag or between the airbag and yourself.
o Do not place any objects (an umbrella, bag, etc.) between the front door and thefront seat. Such objects may become dan-gerous projectiles and cause injury if thesupplemental side air bag inflates.
o To prevent unexpected deployment of the side air bag that may result in personalinjury,avoid impact to the side airbag sen-sor when the ignition key is on. FB110C2-F SRS Care
YT10355A
The SRS is virtually maintenance-free and so there are no parts you can safely service byyourself. The entire SRS system must be in-spected by an authorized Hyundai dealer 10years after the date that the vehicle was manu-factured. Any work on the SRS system, such as removing, installing, repairing, or any work on the steeringwheel must be performed by a qualified Hyundaitechnician.Improper handling of the SRS system may resultin serious personal injury.