2003 Hyundai Coupe steering wheel

DRIVING YOUR HYUNDAI 2- 3
SB050B1-E
STEERING WHEEL LOCK
When the key is removed, the steering column
lock will be activated and will engage when the steering wheel is turned to the appropriate po-sition. It is not necessary to turn the wheel untillocked each time the key is removed since inthe event of any unauthorized attempt at re-moval, the lock will become effective as soonas the steering wheel is turned. To unlock thesteering, insert the key and turn to the "ACC"position. If the steering is locked, it may benecessary to rock the steering wheel slightly tofacilitate turning the key. Under no circum-stances should the key be forced since break-age of the key will occur. SC060A1-E
STARTING THE ENGINE
C050A01E
SC090D1-F
To Remove the Ignition Key
1. Turn the ignition key to the "ACC" position.
2. Simultaneously push and turn the ignition key counterclockwise from the "ACC" posi-tion to the "LOCK" position.
3. The key can be removed in the "LOCK" position.C070C01E
LOCK ACC
ON
START LOCK
ON
START
1. Ensure that the transaxle is in neutral and that the clutch pedal is held depressed (manual transaxle) or the transaxle selectoris at the "P" position (automatic transaxlevehicle).
2. Turn the ignition key to and hold at the "Start" position until the engine starts. Whenthe engine has started, release the key.

DRIVING YOUR HYUNDAI
2- 8 when you are driving down a long hill, slow down and shift to a lower gear. When you dothis, engine braking will help slow the car.
o Slow down before shifting to a lower gear. Otherwise, the lower gear may not be en-gaged.
o Always use the parking brake. Do not de- pend on placing the transaxle in "P" to keepthe car from moving.
o Exercise extreme caution when driving on a slippery surface. Be especially careful whenbraking, accelerating or shifting gears. On aslippery surface, an abrupt change in vehi-cle speed can cause the drive wheels tolose traction and the vehicle to go out ofcontrol.
WARNING:
o Avoid high cornering speeds.
o Do not make quick steering wheel move- ments, such as sharp lane changes or fast, sharp turns.
o Always wear your seat belts. In a collision crash, un unbelted personis significantly more likely to die than aperson wearing a seatbelt.
o The risk of rollover is greatly increased if you lose control of your vehicle at high-way speeds.
o Loss of control often occurs if two or more wheels drop off the roadway andthe driver oversteers to reenter the road-way. o In the event your vehicle leaves the road-
way, do not steer sharply. Instead, slowdown before pulling back into the travellanes.
o Never exceed posted speed limits. SC140A1-E EFFECTIVE BRAKING Braking system performance and friction mate- rial life are greatly affected by the driving styleadopted. The following suggestions are made toassist in achieving the best results from thebraking system.
o Anticipate the road and conditions ahead in order that heavy braking may be avoided.
o When descending long gradients, use the engine to assist in retarding the vehicle to minimize the possibility of brake fade occur-ring.
o When trailer towing, ensure that the trailer brakes function correctly and use enginebraking to assist the vehicle braking system.
o Use only genuine Hyundai replacement brake pads and shoes to ensure consistentfriction characteristics and wear rates.
o After driving through deep water (e.g. fording), the brakes may become wet andperformance reduced. Always check brakeefficiency after emerging from the water anddry the brakes by lightly depressing thebrake pedal several times whilst driving slow-ly.
C090I01L-GAT
CAUTION:
o Shift into "R" and "P" position only when the vehicle has completely stopped.
o Do not accelerate the engine in reverse or any of the forward positions with the brakes applied.
o Always apply the footbrake when shift- ing from "P" or "N", to "R", "D"position.
o Do not use the "P" (Park) position in place of the parking brake. Always setthe parking brake, shift the transaxle into"P" (Park) position and turn off the igni-tion when you leave the vehicle, evenmomentarily. Never leave the vehicleunattended while the engine is running.
o Check the automatic transaxle fluid level regularly, and add fluid as necessary.
C090N02O-AAT
Good Driving Practices
o Never move the gear selector lever from "P" or "N" to any other position with the acceler- ator pedal depressed.
o Never move the gear selector lever into "P" when the vehicle is in motion.
o Be sure the car is completely stopped be- fore you attempt to shift into "R".
o Never take the car out of gear and coast down a hill. This may be extremely hazard-ous. Always leave the car in gear whenmoving.
o Do not "ride" the brakes. This can cause them to overheat and malfunction. Instead,

DRIVING YOUR HYUNDAI 2- 9
o Apply the parking brake only when the vehi-
cle is at rest.
o Since the power assistance provided by the brake servo is derived from the engine, coasting with the engine turned off or towingof the vehicle with the engine turned off willresult in greatly increased pedal pressuresbeing required to stop the vehicle.
o Do not hold the vehicle on the upgrade with the accelerator pedal. This can cause thetransaxle to overheat. Always use the brakepedal or parking brake.
SC140B1-E
ANTI-LOCK BRAKE SYSTEM (Not all models)
The Anti-Lock Brake System (ABS) is designed
to prevent wheel lock-up during sudden braking or on hazardous road surfaces. The ABS con-trol module monitors the wheel speed and con-trols the pressure applied to each brake. Thus,in emergency situations or on slick roads, ABSwill increase vehicle control during braking.
NOTE: During ABS operation, a slight pulsation
may be felt in the brake pedal when the brakes are applied. Also, a noise may beheard in the engine compartment while brak-ing. These conditions are normal and indi-cate that the anti-lock brake system is func-tioning properly. WARNING: ABS will not prevent accidents due to im-
proper or dangerous driving manoeuvres. Even though vehicle control is improvedduring emergency braking, always maintaina safe distance between you and objectsahead. Vehicle speeds should always bereduced during extreme road conditions.
The braking distance for cars equipped with
an anti-lock braking system may be longerthan for those without it in the followingroad conditions.
o Rough, gravel or snow-covered roads.
o With tire chains installed.
o On roads where the road surface is pit- ted or has different surface height.
These roads should be driven at reduced
speeds. The safety features of an ABS equipped vehicle should not be tested byhigh speed driving or cornering. This couldendanger the safety of yourself or others. C300A03Y-EAT
TRACTION CONTROL SYSTEM (TCS) (Not all models)
HGK156A-D
On slippery road surfaces, the traction control system (TCS) limits the drive wheels from spin-ning excessively, thus helping the car to accel-erate. It also provides sufficient driving forceand steering performance as the car turns ataccelerated speeds.
SLIP Control Limits the drive wheels from spinning exces-sively during starting or while making accelerat-ed turns on slippery roads to avoid losing thedriving force of the front wheels.
Driving hints TCS does not actively apply brakes. Be sure todecelerate the car sufficiently before enteringcurves.

DRIVING YOUR HYUNDAI
2- 12 WARNING:
It is not recommended that the vehicle be used for towing until the first 1000 miles ofRunning In has been completed. All Hyundaicoupe models are suited to towing trailersand caravans up to the limits indicated onpage 2-14. Coupe models fitted with auto-matic transaxle have a transaxle oil coolerand further transaxle cooling should not berequired.
SC200A1-E
TRAILER AND CARAVAN TOWING
Nose weightSSA2200B
Total trailer weight
o When driving in extreme conditions, the
windscreen wiper blades may fail to clear the screen properly due to the formation ofice upon the blade edge. It will therefore benecessary to periodically remove such iceto restore their efficiency.
o If the power operated door mirrors become frozen, attempts to adjust these may dam-age the mechanism.
o The formation of snow or ice built up inside the wheel arches may interfere with the roadwheels or steering mechanism. In such in-stances, unusual noises or an increase insteering effort may result. Therefore, ensurethat the wheel arches are checked periodi-cally and any accumulated snow or iceremoved.
o It is advisable to carry emergency equip- ment including, torch, shovel, tow rope, blan-kets etc., if a journey is to be undertaken intoareas of severe road conditions.
ZC170D1-E
Door Locks
Should the door lock mechanism become fro-
zen, a proprietary lock de-icer should be used.Alternatively, warming the door key may thawthe door lock. However, the key should behandled carefully to avoid burning the fingers.
Never attempt to thaw a frozen door lock using
hot water, since the water will eventually freezeand compound the problem.
NOTE:The proper temperature for using the immo-
bilizer key is from -40°F (-40°C) to 176°F(80°C). If you heat the immobilizer key over176°F (80°C) to open the frozen lock, it maycause damage to the transponder in its head. SC170E1-E Windscreen Washers and Wipers
The windscreen washer bottle should be filled
with a solution of water and a proprietary winter screen wash additive. The windscreen wipersshould not be used if the blades are frozen tothe windscreen or if they are covered withsnow, before this is removed.
NOTE: Never allow undiluted screen washer fluid
additive to spill upon the paintwork or use engine coolant anti-freeze since damage tothe paintwork may result.

3-7
IN CASE OF EMERGENCY
SD080A1-E VEHICLE TOWING OR RECOVERY
o OK FOR AUTOMATIC OR MANUALTRANSAXLE EQUIPPED VEHICLE
CAUTION: An incorrect tow or recovery could result in serious damage to the vehicle. If any damageto the suspension, steering or transaxle isapparent or suspected, a towing dolly mustbe used.
HGK194
SD070J1-E 8. Lower Vehicle and Tighten Nuts Lower the car to the ground turning the wheel nut wrench counterclockwise. When the vehicle isfirmly on the ground, remove the jack and tightenthe wheel nuts securely. At the first availableopportunity, the wheel nut torque should bechecked with a suitable torque wrench. Wheel nut tightening torque Steel wheel & aluminium alloy wheel:90-110 Nm. (65-80 lb.ft) SD070K1-E AFTER CHANGING WHEELS The pressure of the spare tyre should be checked at the first available opportunity. If any doubtexists as to the tyre pressure, the vehicle shouldbe driven slowly to the nearest service stationand the tyre pressure checked and adjusted asrequired.If the valve cap is lost from any of the valves, areplacement should be obtained and fitted at thefirst available opportunity. The valve cap pre-vents the ingress of dirt which may cause thevalve to stick and therefore leak and is part of thevalve sealing function. Ensure that the spare wheel, jack and wheel nut wrench as well tools are correctly located in theboot of the vehicle to prevent damage and noise.
D080A01GK
HGK195

IN CASE OF EMERGENCY
3-8 since the steering lock is not designed to withstand the force required to hold the frontwheels straight during the tow.
o The vehicle must not be towed with the front wheels on the ground for more than thirtymiles.
SD100A2-E Automatic Transaxle Vehicle
o NOT OK FOR AUTOMATIC TRANSAXLE QUIPPED VEHICLE
o OK FOR MANUAL TRANSAXLE
The vehicle may be towed by the conventional method using the towing eye at the front of thevehicle as an attachment point.In addition, a suspended tow may be given to thefront of the vehicle without an towing dolly. In theevent of a suspended tow being given to the rearof the vehicle, the use of an towing dolly isimperative.
o OK FOR AUTOMATIC OR MANUAL TRANSAXLE EQUIPPED VEHICLE
CAUTION: The following restriction must be observedin order to avoid serious damage to thetransaxle.The vehicle must never be towed from therear with the front wheels on the ground.The vehicle must not be towed until transaxlefluid has been added to bring the level up tothe "HOT" marking on the dipstick. (The levelwill need to be reduced again after towing).The vehicle must not be towed at speedsfaster than 25 mph. or distances greater thanfifty miles. The general points regarding thesteering lock etc. described in the precedingsection (Manual transaxle vehicle) should beobserved.
D120A01A-EAT IF YOU LOSE YOUR KEYS Information about the key of immobilizer system will be found on page 1-2.
SD090A1-E Manual Transaxle Vehicle
o OK FOR AUTOMATIC OR MANUAL
TRANSAXLE EQUIPPED VEHICLE WITH NO DAMAGE
The vehicle may be towed by the conventionalmethod using the towing eye at the front of thevehicle as an attachment point. In addition, asuspended tow with or without an towing dollymay be used with either the front or the rearwheels being suspended, provided the abovecaution is observed. In addition, the following points must be noted:
o If towing by conventional means, the ignition key must be at the "ACC" position, otherwise the steering lock will be activated.
o Because the brake system and steering sys- tem power assistance is derived from theengine, the amount of effort required to stop orsteer the vehicle will be greater than normal.
o If a suspended tow is being given to the rear, the ignition key must be at the "ACC" position HGK200
D080C01GK
HGK199

VEHICLE MAINTENANCE REQUIREMENTS 5-3
I I I I II I I I I
R
III I II I I
F030C02GK-EAT R : REPLACE I : INSPECT AND, AFTER INSPECTION, CLEAN, ADJUST, REPAIR OR REPLACE IF NECESSARY
GENERAL MAINTENANCE COOLING SYSTEM COOLANT COOLANT SPECIFIC GRAVITYMANUAL TRANSAXLE OIL AUTOMATIC TRANSAXLE FLUID BRAKE PIPES, HOSES, AND CONNECTIONSBRAKE FLUID CLUTCH FLUID REAR BRAKE LININGS AND CYLINDERSBRAKE PADS SUSPENSION AND STEERING SYSTEM FRONT SUSPENSION BALL JOINTSPOLLEN FILTER (For Blower unit) REAR WHEEL BEARINGS TYRE CONDITION AND PRESSURE (incl. Spare)LUBRICATE LOCKS AND HINGES CHECK ALL ELECTRICAL SYSTEMS ROAD TESTCHECK ALL SYSTEMS WITH HI-SCAN CHECK 4 GAS DRIVE SHAFT & BOOT
MILES X 1000 MONTHS
NO. DESCRIPTION1 2 34 5 67 8 9
10 11 1213 14 1516 17 1819 20 21I I I I II I I I I
R
III I II I I
10 12 202430364048 50606072
I
R I I I I
R R I I I I
R
III I II I II
R I I I I
R R I I I I
R
III I II I I I I I I II I I I I
R
III I II I I I
R II
R I
R R I I I I
R
III I II I I

VEHICLE MAINTENANCE REQUIREMENTS
5- 6
6ZF070D1-A
o Manual transaxle oil Inspect the manual transaxle oil according to the maintenance schedule. NOTE: If the oil level is low, check for possible leaksbefore adding oil. Do not overfill.
6ZF070H1-A
o Rear brake drums and linings/
parking brake
Check the rear brake drums and linings for scoring, burning, leaking fluid, broken parts, andexcessive wear. Inspect the parking brake sys-tem including the parking brake lever and cables.For detailed service procedures, refer to theShop Manual. 6ZF070J1-A
o Brake pads, calipers and rotorsCheck the pads for excessive wear, discs for run out and wear, and calipers for fluid leakage. 6ZF070K1-A
o Exhaust pipe and mufflerVisually inspect the exhaust pipes, muffler and hangers for cracks, deterioration, or damage.Start the engine and listen carefully for anyexhaust gas leakage. Tighten connections orreplace parts as necessary. 6ZF070L1-A
o Suspension mounting bolts Check the suspension connections for loose- ness or damage. Retighten to the specified torque.
F070E03A-AAT
o Automatic transaxle fluid The fluid level should be in the "HOT" range of the dipstick, after engine and transaxle are at normaloperating temperature. Check the AutomaticTransaxle Fluid level with the engine running andthe transaxle in neutral, with the parking brakeproperly applied. Use DIAMOND ATF SP- III,
SK ATF SP- III when adding or changing fluid. 6ZF070M1-A
o Steering gear box, linkage & boots/
lower arm ball joint
With the vehicle stopped and engine off, check for excessive freeplay in the steering wheel.Check the linkage for bends or damage. Checkthe dust boots and ball joints for deterioration,cracks, or damage. Replace any damaged parts. 6ZF070N1-A
o Power steering pump, belt and hos-
es
Check the power steering pump and hoses for leakage and damage. Replace any damaged orleaking parts immediately. Inspect the powersteering belt for evidence of cuts, cracks, exces-sive wear, oiliness and proper tension. Replaceor adjust it if necessary.
6ZF070F1-A o Brake hoses and linesVisually check for proper installation, chafing, cracks, deterioration and any leakage. Replaceany deteriorated or damaged parts immediately. 6ZF070G2-A
o Brake fluidCheck brake fluid level in the brake fluid reser- voir. The level should be between "MIN" and"MAX" marks on the side of the reservoir. Useonly hydraulic brake fluid conforming to DOT 3 orDOT 4.
6ZF070B1-A
o Cooling systemCheck the cooling system part, such as radiator, coolant reservoir, hoses and connections forleakage and damage. Replace any damagedparts. 6ZF070C1-A
o Coolant The coolant should be changed at the intervals specified in the maintenance schedule.