2003 Hyundai Coupe clock

CONTROLS AND EQUIPMENT1- 67
B870A01A-GAT ANTENNA Fixed Rod Antenna Your car uses a fixed rod antenna to receive both AM and FM broadcast signals.This antenna is a removable type. To remove theantenna, turn the antenna counterclockwise. Toinstall the antenna, turn the antenna clockwise. CAUTION: Be sure to remove the antenna before wash-ing the car in an automatic car wash or theantenna may be damaged.
B870A01F

DRIVING YOUR HYUNDAI 2- 3
SB050B1-E
STEERING WHEEL LOCK
When the key is removed, the steering column
lock will be activated and will engage when the steering wheel is turned to the appropriate po-sition. It is not necessary to turn the wheel untillocked each time the key is removed since inthe event of any unauthorized attempt at re-moval, the lock will become effective as soonas the steering wheel is turned. To unlock thesteering, insert the key and turn to the "ACC"position. If the steering is locked, it may benecessary to rock the steering wheel slightly tofacilitate turning the key. Under no circum-stances should the key be forced since break-age of the key will occur. SC060A1-E
STARTING THE ENGINE
C050A01E
SC090D1-F
To Remove the Ignition Key
1. Turn the ignition key to the "ACC" position.
2. Simultaneously push and turn the ignition key counterclockwise from the "ACC" posi-tion to the "LOCK" position.
3. The key can be removed in the "LOCK" position.C070C01E
LOCK ACC
ON
START LOCK
ON
START
1. Ensure that the transaxle is in neutral and that the clutch pedal is held depressed (manual transaxle) or the transaxle selectoris at the "P" position (automatic transaxlevehicle).
2. Turn the ignition key to and hold at the "Start" position until the engine starts. Whenthe engine has started, release the key.

IN CASE OF EMERGENCY
3-4 Remove the spare wheel, jack and tool bag from the boot.
SD070D1-E 2. Block the Wheel Block the wheel that is diagonally opposite from the flat tyre to prevent the vehicle from rollingwhen the car is raised on the jack.
D060A01GK-EAT 1. Obtain Spare Tyre and Tool
D060K01FC-EAT Wheel Cap (Not all models)
1. Wrap a piece of cloth around the tip of the
driver to avoid scratching.
2. Insert a driver into the groove of the wheel cap and pry gently to remove the wheel cap.
3. Change the flat tyre. 4. Reinstall the wheel cap by fitting the boss of the
wheel cap in the groove of the wheel, hitting the
centre of the wheel cap with hand.
Boss
HGK196
HGK224
Groove
Groove
HGK189
HGK191
The jack is located in the right side of luggage trim. Remove the jack cover with screwing thebolts. Turn the jack at the end counterclockwiseto low the jack height by using driver or wrenchbar and take out it from the bracket.
Flat tyre
HGK192

3-5
IN CASE OF EMERGENCY
SD070E1-E 3. Loosen Wheel Nuts The wheel nuts should be loosened slightly be- fore raising the car. To loosen the nuts, turn thewheel brace counterclockwise. Ensure that thewheel brace socket is seated properly on the nutand that it cannot slip. Do not remove the nuts atthis stage. SD070F1-F 4. Put the Jack in Place The base of the jack should be placed on firm, level ground. The jack should be positioned asshown in the drawing.
HGK193HGK186
D060F02E-EAT 5. Raising the Car After inserting a bar into the wheel nut wrench, install the bar into the jack as shown in the draw-ing. To raise the vehicle, turn the wheel nut wrenchclockwise. As the jack begins to raise the vehicle,double check that it is properly positioned and will
not slip. If the jack is on soft ground or sand, placea board, brick, flat stone or other object under thebase of the jack to keep it from sinking.Raise the car high enough so that the fully inflatedspare tire can be installed. To do this, you will needmore ground clearance than is required to removethe flat
tyre.
WARNING:Do not get under the car when it is supportedby the jack! This is very dangerous as the jackcould fall and cause serious injury or death.No one should stay in the car while the jack isbeing used.
HFC4022
Wrench bar
Wheel nut wrench

3-7
IN CASE OF EMERGENCY
SD080A1-E VEHICLE TOWING OR RECOVERY
o OK FOR AUTOMATIC OR MANUALTRANSAXLE EQUIPPED VEHICLE
CAUTION: An incorrect tow or recovery could result in serious damage to the vehicle. If any damageto the suspension, steering or transaxle isapparent or suspected, a towing dolly mustbe used.
HGK194
SD070J1-E 8. Lower Vehicle and Tighten Nuts Lower the car to the ground turning the wheel nut wrench counterclockwise. When the vehicle isfirmly on the ground, remove the jack and tightenthe wheel nuts securely. At the first availableopportunity, the wheel nut torque should bechecked with a suitable torque wrench. Wheel nut tightening torque Steel wheel & aluminium alloy wheel:90-110 Nm. (65-80 lb.ft) SD070K1-E AFTER CHANGING WHEELS The pressure of the spare tyre should be checked at the first available opportunity. If any doubtexists as to the tyre pressure, the vehicle shouldbe driven slowly to the nearest service stationand the tyre pressure checked and adjusted asrequired.If the valve cap is lost from any of the valves, areplacement should be obtained and fitted at thefirst available opportunity. The valve cap pre-vents the ingress of dirt which may cause thevalve to stick and therefore leak and is part of thevalve sealing function. Ensure that the spare wheel, jack and wheel nut wrench as well tools are correctly located in theboot of the vehicle to prevent damage and noise.
D080A01GK
HGK195

OWNER MAINTENANCE 6-5
See the lubrication chart on the page 9-3. NOTE:
o The use of a 5W-20 multi grade oil is not
recommended for sustained high speeduse.
o When replacing or adding the oil, below SAE 10W-30 is recommended.Using a high viscosity oil of SAE 15W-40and over makes malfunction of CVVT en-gine when the engine is cool. SG030D1-E ENGINE OIL REPLENISHMENT If the indicated oil level is at or below the lower mark of the dipstick, oil should be added until thelevel is at or below the upper mark.To add oil to the engine, remove the filler cap byrotating in an counterclockwise direction andpour engine oil into the engine. Before checkingthe level again, allow several minutes for the oilto drain into the sump. Replace the oil filler caprotating it in a clockwise direction until tight.The quantity of oil required to raise the level from theminimum to maximum level is approximately 1 litre.
SG030C1-E Engine Oil Level The engine oil level should be checked with the engine at normal operating temperature and thevehicle parked upon level ground.Prior to checking the level, the vehicle should beallowed to stand for several minutes after theengine has been switched off to allow the oil todrain back to the sump.Withdraw the dipstick and wipe it with a clean rag.Replace the dipstick fully and withdraw againwhen the oil level may be read from the stick.Normal oil level is indicated when the oil ispresent between the two marks on the stick. It isnot necessary to add oil if the level is above thelower mark and in any case, oil must not beadded to the degree that the level exceeds theupper mark. Replace the dipstick fully after check-ing the level.
HGK210HGK211
DOHC
DOHC V6
HGK259
2.0 L DOHC CVVT
V6

OWNER MAINTENANCE
6-6 WARNING: The oil being drained from the engine will behot. Care should be exercised to preventscalding.
4. When the oil has drained from the sump,
replace the drain plug using a new washer ensuring that the plug is not over tightened.
Tightening torque :
4.5 ~ 4.0 kgf.m (1.6/2.0L)4.5 ~ 3.5 kgf.m (2.7L)
5. Remove the oil filter by rotating counterclock- wise, using a proprietary oil filter removal toolif necessary. Note that the oil filter will containapproximately 0.5 litres of oil and this shouldbe collected in a suitable receptacle.
6. Install a new oil filter having smeared the sealing ring with clean oil and rotating clock-wise until the filter contacts the mounting andthen a further one half turn. Do not over-tighten. Tightening torque: 1.2 ~ 1.6 kgf.m.
7. Pour the specified quantity of the recom- mended oil into the engine and replace the filler cap. Start the engine and ensure that nooil leaks exist. Turn off the engine and after acouple minutes, recheck the oil level.
WARNING:Prolonged and repeated contact with usedengine oils may result in serious skin disor-ders including dermatitis and cancer. Avoidcontact with skin as far as possible and al-
G040A02GK-EAT ENGINE OIL AND FILTER REPLACEMENT The engine oil and filter must be changed at the time or mileage interval specified in the mainte-nance schedule. If the vehicle is operated undersevere or adverse conditions, the oil and filtermust be replaced more frequently.To replace the oil and filter, proceed as follows:
1. Ensure that the engine is at normal operating
temperature and park the vehicle on level ground with the parking brake securely ap-plied and the engine turned off.
2. Open the bonnet and remove the oil filler cap.
3. Prepare a suitable receptacle to collect the displaced oil and remove the drain plug fromthe sump.
G350A01A-GAT ENGINE OIL CONSUMPTION Function of engine oil Engine oil has the primary function of lubricating and cooling the inside of the engine. Engine oil consumption It is normal that an engine should consume some engine oil while normal driving. The cause of oilconsumption in a normal engine are as follows;
o Engine oil is used to lubricate pistons, piston
rings and cylinders. A thin film of oil is left on the cylinder wall whena piston moves downwards in the cylinder.High negative pressure generated during en-gine operation sucks some of the oil into thecombustion chamber.This oil with some oil of the cylinder wall isburned by the high temperature combustiongases during the combustion process.
o The engine oil consumption is strongly ef- fected by the viscosity and quality of oil,engine rpm and driving condition etc.More engine oil may be consumed undersevere driving conditions such as high speeds,frequent acceleration and deceleration, com-pared to normal driving.
G040A01GK
DOHC V6

OWNER MAINTENANCE
6-8 CAUTION: Sparking plugs must only be cleaned usingpurpose designed equipment. Wire brushingmay damage the centre electrode insulatorcausing mis-firing to occur. Only the correctgrade of sparking plug should be used. Useof an incorrect grade may result in seriousengine damage.
3. With the heater temperature control set to the
"HOT" position, remove the radiator cap andopen the radiator drain tap.
4. When the engine coolant has drained com- pletely, close the drain tap ensuring that thisis not over tightened.
5. Prepare a suitable quantity of new engine coolant (refer to section 9) and pour this intothe radiator.
6. Start the engine with the radiator cap still removed and continue to add coolant as thelevel decreases as air is expelled from thesystem. When the level remains constant,replace the radiator cap and replenish thecoolant reservoir.
7. When the engine is hot, check to ensure that no coolant leaks are present.
WARNING:The cooling fan is controlled by engine cool-ant temperature and may sometimes operateeven when the engine is not running. Useextreme caution when working near the bladesof the cooling fan so that you are not injuredby a rotating fan blade. As the engine coolanttemperature decreases, the fan will automati-cally shut off. This is a normal condition. G060B02GK-EAT SPARKING PLUG REPLACEMENT This operation should only be performed when the engine is cold.
1. Remove the engine rocker cover.NOTE: It is recommended that the spark plug forEngine 2.7L should be changed by an autho-rized Hyundai dealer.
2. Remove plug lead from the sparking plug to
be replaced, pulling the lead by the rubber cap. (Pulling the lead may damage the carbonconductor).
3. Clean around the base of the plug to be removed, and install the plug socket ensuringthat the ceramic insulator does not becomedamaged. Turn the socket counterclockwiseto remove the plug.
YN60100A0.039 ~ 0.043 in. (1.0 ~ 1.1 mm)
0.039 ~ 0.043 in. (1.0 ~ 1.1 mm)
DOHC V6
HGK256