2003 HONDA ELEMENT clock

µIf you need to connect the battery to
a charger, disconnect both cables to
prevent damage to the vehicle’s
electrical system.
If the terminals are severely cor-
roded, clean them with baking soda
and water. Then use a wrench to
loosen and remove the cables f rom
the terminals. Always disconnect the
negative ( ) cable f irst and recon-
nect it last. Clean the battery termi-
nals with a terminal cleaning tool or
wire brush. Reconnect and tighten
the cables, then coat the terminals
with grease. If your vehicle’s battery is
disconnected or goes dead, the audio
system will disable itself . The next
timeyouturnontheradioyouwill
see ‘‘CODE’’ in the f requency display.
Use the preset buttons to enter the
f ive-digit code (see page ). You
will then have to set the clock and
enter your station presets.
152
On EX models
Battery
Maint enance241
The battery gives off explosive
hydrogen gas during normal
operation.
A spark or flame can cause the
battery to explode with enough
force to kill or seriously hurt you.
Wear protective clothing and a
face shield, or have a skilled
mechanic do the battery
maintenance. Charging the battery with the cables
connected can seriously damage your
vehicle’s electronic controls. Detach
the battery cables bef ore connecting
the battery to a charger.

Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Remove the rubber weather seal
by pulling on the tab.
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way and remove the bulb.Insert the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place, and clip the end into
the slot.
Install the rubber seal over the
back of the headlight assembly.
Make sure it is right side up; it is
marked ‘‘TOP.’’
Push the electrical connector onto
the new bulb. Make sure it is
connected securely.
Turn on the headlights to test the
new bulb.
(Driver’s side)
Install the f ront end of the air
intake duct.
Open the hood. The f ront
parking/turn signal light is next to
the headlight bulb. On the driver’s
side, remove the f ront end of the
air intake duct by pulling it out.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
1.
2.
3.
4. 5.
6.
7.
8.
2.
CONT INUED
Lights
Maint enance
Replacing a Front Parking/Turn
Signal Light Bulb
259

Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.Place a cloth between the trim of
the lens and the body, at the top of
the lens. Remove the front side
marker light assembly by caref ully
prying on the trim of the lens with
a small f lat-tipped screwdriver.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Install the f ront end of the air
intake duct. (Driver’s side)
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.
1.
3.
4.
5.
2.
3.
6.
Lights
Maint enance
Replacing a Front Side Marker
Light Bulb
260

Turn on the lights to make sure
the new bulb is working.
Put the light assembly back into
the body, bottom first. Push on the
top edge until it snaps into place.Open the hatch and the tailgate.
Remove the two mounting screws
with a Phillips-head screwdriver,
and remove the taillight assembly
f rom the body by pulling it back.
Determine which of the three
bulbs is burned out: brake/
taillight, turn signal light or back-
up light.Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Put the socket back into the light
assembly and turn it clockwise to
lock it in place.
1.
4.
5.
2.3.
4.
6.
CONT INUED
Lights
Maint enance
Replacing Rear Bulbs
261

Pull the bulb straight out of its
socket. Push the new bulb in until
it bottoms in the socket.Turn on the parking lights and
check that the new bulb is
working.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
When reinstalling the taillight
assembly, f irst place the two pins
in the holes in place. Tighten the
two mounting bolts.
Place a cloth and insert a small
f lat-tipped screwdriver between
the left edge of the lens and the
housing. The lens will come down.Put the lens back into the light
assembly, right side f irst. Push on
the lef t edge until it snaps into
place.
1.
2.
6.
7.
3.
4.
5.
Replacing a Rear License Plate
Bulb
Lights
Maint enance262

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.Testthelightstomakesurethe
new bulb is working.
Put the socket back into the light
assembly and turn it clockwise to
lock it in place.
Put the cover back onto the light
assembly. Push it on until it locks
in place.
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise. Open the hatch. Remove the light
assembly cover by pushing in on
the tabs on both sides and pulling
the cover down.
1.
2. 3.4.
5.
6.
Replacing a High-mount Brake
Light Bulb
Maint enance
Lights
263

Push the rear edge of the handle
to raise the handle loop and pull up
the loop to raise the cargo area
f loor.
Unscrew the wing bolt and take
the spare tire out of the cargo area.Remove the tools and the jack. To
remove the jack, turn the jack’s
end bracket counterclockwise to
loosen it.
Loosen the f ive wheel nuts 1/2
turn with the wheel wrench.
8.
7.
6. 5.
Changing a Flat T ire
T aking Care of t he Unexpect ed278
JACK WHEEL NUTS

CONT INUED
Locate the jacking point nearest
thetireyouneedtochange.Itis
pointed to by an arrow molded into
the underside of the body. Place
the jack under the jacking point.
Turn the end bracket clockwise
until the top of the jack contacts
the jacking point. Make sure the
jacking point tab is resting in the
jack notch.Use the extension and wheel
wrench as shown to raise the
vehicle until the f lat tire is of f the
ground.
Remove the wheel nuts and f lat
tire. Temporarily place the f lat tire
on the ground with the outside
surf ace of the wheel f acing up.
Placing the wheel face down could
mar its f inish.
9.
10. 11.
Changing a Flat T ire
T aking Care of t he Unexpect ed279
EXTENSION
WHEEL WRENCH
JACKING POINTS