2003 HONDA CIVIC Panel

Fuel Supply System
Fuel Gauge Sending Unit Test
Special Tools Required
Fuel sender wrench 07XAA-001010A
NOTE; For the fuel gauge system circuit diagram, referto the Gauges Circuit Diagram (see page 22-58||.
1. Checkthe No. 10 fUETER {7.5A)fuse in the under-
dash fuse/relay box before testing.
2. Do the gauge drive circuit check (see page 22-56|l.
' lf the fuel gauge needle sweeps from minimuni
to maximum position and then returns to the
minimum position. the gauge is OK. Go to step 3.. lf the fuel gau ge need le does not sweep from
minimum to maximum position position and
then return to the minimum position, replace thegauge assembly and retest.
3. Turn the ignition switch OFF.
4. Remove the rear seat cushion {see page 20-80).
5. Remove the access panel (A)from the floor.
6. Disconnect the fuel pump 5P connector {B).
-ztr
11-156
7. Measure voltage between fuel pump 5P connectorterminals No. 1 and No. 2 with the ignition switchON (ll). There should be battery voltage.
. lf the voltage is as specified, go to step 8.. lf the voltage is notasspecified,checkfor:
- an open in the YEUBLK or BLK wire.- poor ground (G551).
FUEL PUMP 5P CONNECTOR
Wire side of female terminals
Turn the ignition switch OFF. Remove the No. 9BACK UP (7.5A)fuse from the under-hood fuse/
relay box for at least 10 seconds, lhen reinstall it.
Install a 2 Q resistor between fuel pump 5P
connector lerminals No. 1 and No. 2, then turn the
ignition switch ON (ll).
FUEL PUMP 5P CONNECTOR
-VVV-
29RESISTOR,
=-a
{Y
\
//,(elrt \
\45/
{YEL/BLK)
Wire side of female terminals

Steering Wheel Disassembly/Reassembly
CONTACT PLATE
MOOULE SET BRACKET
STEERING WHEEL REAB COVER
STEERING WHEEL
ACCESS PANEL A
75*-=offi
,/*
ffi)Y /-f
b accEss PANEL B
CRUISE CONTROL SWITCH
CONNECTOR HOLDERS
17-7

EPS Control Unit Removal/
Installation
1. Remove the passenger's under panel.
2. Turn up the floor carpel, remove lhe EPS control
untr.
Disconnect the EPS control unit connectors.
lnstallthe EPS control unit in the reverse order of
removal.
After installation, start the engine, and let it idle.
Turn the steering wheelfrom lock-to-lock several
times. Check that the EPS indicator does not come
on.
3.
E
Tie-rod Ball Joint Boot Replacement
Special Tool Required
Attachment, 42 mm 07OAD-P0A0100
l. Remove the boot from the tie-rod end, and wipe the
old grease off the ball pin.
2. Pack the lower area of the ball pin(A)wilhfresh
mulr purpose grease.
3. Pack the interior of the new boot (B) and lip (C) with
fresh multipurpose grease.
Note these items when installing new grease;
. Keep grease offthe boot installation section (D)
and the tapered section (E) of the ball pin.
. Do not allow dust, dirt, or other foreign materials
to enter the boot.
4. Installthe new boot (A) using the specialtool. The
boot must not have a gap at the boot installation
sections (B). After installing the boot. check the ball
pin tapered section for grease contamination, and
wipe it if necessary.
07(lAD-P0A0100
*-4
r/ \-,d______i.l+_D
-6rA
17-67

Body
DoorsComponent Location Index ...........Door Panel Removal/lnstallation .....,..........Door Outer Handle ReplacementDoor Latch ReplacementDoor Glass and RegulatorReplacementDoor Sash Trim Replacement .......................
Door Glass Outer WeatherstripReplacement
Door Weatherstrip Beplacement
Door Glass Adjustment .................................Door Position Adjustment .............................Door Striker Adiustment ................................MirrorsComponent Location Index ...........................Power Mirror Replacement ...........................Mirror Holder Replacement ...........................Rearview Mirror Rep1acement ......................
GlassComponent Location Index ...........................Windshield Replacement
Bear Window Rep1acement ...........................
Ouarter Glass Replacement ..........................MoonroofComponent Location Index ...........................Symptom Troubleshooting Index
Glass Height Adjustment ...............................
Glass ReplacementWind Def lector 8ep1acement ........................Drain Channel Rep1acement ..........................Sunshade Replacement .................................Motor ReplacementFrame and Drain Tube Replacement ............Drain Channel Slider and Cable AssemblyReplacementLimit Switch Adjustment ...............................Closino Force and ODenina Draq Check ......lnterioi TrimComponent Location Index ...........................Trim Removal/lnstallation DoorArea ..........Trim Removal/lnstallation-Rear Side AreaTrim Removal/lnstallation-Cargo Floor AreaTrim Removal/lnstallation-Hatch Area .........Headliner Removal/lnstallation* Carpet Rep1acement .......................................ConsolesConsoles, Front and RearRemova l/lnsta llationFront Console Disassembly/Reassembly .....
20-220,420-620-7
20-920 t0
20- 10
20-1120-1120-1220 13
20-1420-1520-1520-16
20 1120-1920-2520-29
20,3520-3620-3720-3120-3820 3920-4020-4120,42
20 4420-4620,44
20-4920 50
20-51
DashboardInstrument Panel Removal/lnstallation ........Driver's Dashboard Lower CoverRemovat InstallationDriver's Dashboard Under CoverRemova t Insta llation
Oriver's Pocket Removal/lnstallation ............Shift Lever Trim Removal/lnstallation ..........Center Panel Removal/lnstallation ...............Passenger's Dashboard Lower CoverRemova l/lnsta llat ionx Glove Box Removal/lnstallationDashboard Side VentRemoval/lnstallation .................................. 20-64Beverage Holder Removal/lnstallation ........ 20-64Driver'sTray Removal/lnstallation ............... 20-65Passenger's Tray Removal/lnstallation ........ 20 65* Dashboard Removal/lnstallation .................. 20-66Steerinq Hanqer Beam Reolacement ........... 20-68Seats "
Component Location Index ........................... 20-10* Front Seat Removal/lnstallation ................... 20-11* Front Seat Disassembly/Reassembly-Driver's .................................. 20-73* Front Seat Disassembly/Reassembly-Passenger's ........................... 20-74* Front Seat Cover Replacement ..................... 2O-75Rear Seat Removal/1nsta11ation ..................... 20-80Rear Seat-back Latch Replacement .............. 20-81Rear Seat-backStriker Replacement ............ 20-81
20-59
20-59
Rear Seat-back Cover Replacement ............. 20-82Rear Seat Cushion Cover Replacement ....... 20.84BumpersFront Bumper Removal/lnstallation .............Rear Bumoer Removal/lnstallation ...............HoodAdjustmentHood Seal ReplacementHood Insulator Rep1acement .........................Hatch
20-6020,6020 6120-62
20-63
20-63
20,8520-86
20-4720,8820,89
20-5220-5320-5420-55
20-5720-58
Adjustment ................... 20-90Hatch Suppon Strut Replacement ................ 20-91Hatch WeatherstriD Reo1acement ................. 20-92
Fuel Fill DoorAdiustment ................... 20-93Exterior TrimFront Grille Replacement ..............Cowl Covers Replac"rn""t .. . .....................A pillar Corner Trim Replacement ................Roof lMolding Replacement ...........................Rear License Trim ReplacementHatch Spoiler 8ep1acement ...........................Emblem Rep1acement .........................
20-9420-9520-9620-9720,9820-9920-100

Doors
Door Panel Removal/lnstallation
SpecialTools Required
Trim pad remover, Snap-on A 177A or equivalent,
commercially available.
NOTE: When prying with a flat-tip screwdriver, wrap it
with protective tape, and apply protective tape around
the related parts. to prevent damage.
1 . Remove the mirror mount cover (see page 20-15).
2. Insert a hex wrench through the hole (A) in the door
grip base (B), Push the door grip cover (C) out to
release the hook (D) and tab (E), and pull out the
cover to release the tabs (F) and hook (G) by hand,
then remove the cover.
20-4
3. Remove the armrest cover (A). Take care not to
scratch the door panel.
-1 Pry out the front edge of the cover to release
the hooks (B).
-2 Pry out the bottom and rear edge of the cover
to release the hooks (C).
-3 Pry out along the top to release the tabs (D).
Remove the screws (A, B), and release the tabs (C),
then remove the door grip base (D). Remove the
screw (A) securing the door panel from the armrest
portion.
Fastgngr Locations
A> : Screw,3 B > : Screw,5
4.

5. Pull out the switch panel (A)to release the hook (B),
then remove the panel from the door panel.
Disconnect the power window switch connector (C).
Release the clips that hold the door panel (A) with a
commercially available trim pad remover (B), then
remove the door panel by pulling it upward.
Remove the door panel with as little bending as
possible to avoid creasing or breaking it,
Fastener Locations95 mm (3.74 in.l
12 mm r q----------i.0.17 in.l r <_--'r-
> : Clip,9
ffi
EtAlmm{0.04 in.l
45 mm {1.77 in.l
7. Disconnect the inner handle cable {A) from the
inner handle (B), and disconnectthe power door
lock switch connector (C) {driver's). Take care not to
bend the cable.
8. Detach the harness clip (A)from the door panel (B).
B
Install the door panel in the reverse order of
removal, and note these items:
. Replace any damaged clips.. Make sure the cable is connected securely, and
the connector is plugged in properly.. Check the window and power door lock
operatrons,
9.
20-5

Doors
Door Outer Handle Replacement
NOTE: Put on gloves to protect your hands.
1, Remove these items:
. Door panel (see page 20-4). Plastic cover, as necessary (see page 20-2)
Raise the glass fully.
Remove the lock rod protector (A).
-l Remove the screw.-2 Release the protector from the latch protector
(B).
-3 Pull the protector down to release the hook (C)
from the door.
Fastener Location
) : Screw, 1
2.
5.
20-6
4. Disconnect the cylinder rod (A), and release the
retainer clip (B). then remove the lock cylinder (C).
Disconnect the outer handle rod (A).
Fastenor Locations
> : Bolt, 2
6x1.0mm9.8 N.m{1.0 kgf.m,7.2 tbt.ft')
6.Remove the maintenance cap (B), and remove the
bolts securing the outer handle (C) while holding
the handle from outside. Release the hook (D). then
remove the outer handle protector (E).

7. Pull out the outer handle (A), then remove it.
Installthe handle in the reverse order of removal,
and note these items:
. Make sure each rod is connected securelv.. Make sure the door locks and opens properly.. When installing the lock cylinder. leavetheouter
door handle bolts loose so the inner protector
does not interfere with the lock cylinder
installation, then tighten the handle bolts.. Install the lock cylinder retaining clip on the
handle, then install the lock cylinder. Be sure the
clip is fully seated in the slot on the lock cylinder.. When reinstalling the door panel, make sure the
plastic cover is installed properly, and is sealed
around the covers Derimeter.
Door Latch Replacement
NOTE: Put on gloves to protect your hands.
1. Remove these items:
3.
4.
. Door panel (see page 20-4). Plastic cover, as necessary (see page 20-2)
Raise the glass fully.
Remove the lock rod protector (see step 3 on page
20-6).
Pullthe glass run channel (A) away as necessary,
and remove the bolt, then remove the center lower
channel (B) by pulling il downward
Fastenor Location
> : Bolt, 1
IIilE
q
6x1.0mm8 N.m{0.8 kgf.m, 6 lbf.ftl
(cont'd)
20-7