2003 HONDA CIVIC Rear

6. Remove the sunshade (A),
::lll' =r'"'---
----.-.. --.,
'l'i
?,
7.Remove both front sunshade base sliders (A) and
both rear sunshade base sliders (B)
t'-^'
'a{
8.
9.
Installthe sunshade in the reverse order of removal,
and check the glass height adjustment (see page
20-37 ).
Check for water leaks. Let the water run freely from
a hose without a nozzle. Do not use a high-pressure
spray.
1.
Motor Replacement
Remove the headliner (see page 20-54).
Put on gloves to protect your hands. Disconnecl the
connector (A), and remove the bolts, then remove
the motor (B).
Fastener Locations
>:Bolt,2 A
@@
..
{0.9 kgf.m.7 rbf.ftl
Installthe motor in the reverse order of removal,
and note these items:
. lvlake surethe connector is plugged in properly.
. Check the motor operation.
20-41

Moonroof
1.
Frame and Drain Tube Replacement
Remove these items:
. Headliner (see page 20-54). Moonroof glass (see page 20-37)
Put on gloves to protect you r hands. Disconnect the motor connector (A), open/close-tilt/close switch connector
{B), moonroof control unit connector {C), auto-stop switch connector (D), and the drain tubes (Ei, and remove the
moonroof relays (F).
Fastenor Locations
> : Bolt, 10
{um
/^
6x1.0mm9.8 N.m(1.0 kgf.m,7.2lbf ft)
4.
5.
2.
irl
@
Remove the interior harness (G) by detaching the harness clips (H).
With an assistant holding the frame (l). remove the bolts, starting at the rear, and release the rear hooks (J) by
moving the f rame forward, then remove the frame.
With the help of an assistant, carefully remove the frame through the passenger's door opening. Take care not to
scratch the interior trim and body, or tear the seat covers.
20-42

6. To remove a front drain valve (A)from the body,
remove the kick panel, left or right (see page 20-50).
Tie a string to the end of the drain tube, then pull
the front drain tube (B) down out of the front pillar.
To remove a rear drain valve (A) from the cargo
compartment, remove the rear side trim panel (see
page 20-51).Detach the clips (B), then remove the
drain tube (C),
B
1.
8. Installthe frame and drain tube in the reverse order
of removal, and note these items:
. Before installing the frame, clear the drain tubes
and drain valves using compressed air.. Check the frame seal.. Clean the surface ofthe frame.. When installing the frame, first attach the rear
hooks into the body holes.. Make sure the connectors are plugged in
properly.
. When connecting the drain tube, slide it overthe
frame nozzle at least 10 mm (0.39 in.)..Installthetubeclip(A) on the drain tube (B) as
shown.
Upward
t-
I
I
B
Check for water leaks. Let the water run freely from
a hose without a nozzle. Do not use a high-pressure
spray.
9.
20-43

Moonroof
Drain Channel Slider and Cable Assembly Replacement
1. Remove the frame (see page 20-42).
2. Remove these parts from the frame:
. Sunshade (see page 20-40). Moonroof motor (see page 20-41)
3. Put on gloves to protect your hands, Remove the
screws (A, B), then remove the slide stops (C) and
cable tube rear brackets (D). Remove the bolts (E)
from the cable tube side bracket (F) and the cable
tube mounting screws (G) from both sides of the
frame (H).
Fastener Locations
A> r Screw.2 B): Screw,2
@@
r):
Position switch side:
6x1.0mmA c g,a N.m
No switch sidel
o
E>:Bolt,2
Screw
6\-'1
6x1.0mm C9.8 N.m11.0 kgf.m, 7.2 lbf.ft)
Detach the onen switch connector clip {l)from the
frame.
B
V
20-44
5. Pivotthe glass bracket (A) down by sliding the link
lifter (B) back, then slide both glass brackets back
with the link lifter.
Slide the cable assembly (A) and both glass
brackets (B) back, then remove them from the
frame (C).

Interior Trim
Component Location Index
HATCH LOWER TRIM PANELoaoe 20-53
HATCH SIDE TRIMpage 20 53
C-PILLAR TRIMpage 20'51
REAR SIDE SHELFpage 20 5l
REAR SIDE TRIM PANELpage 20-51
B.PILLAR UPPEB TRIMpage 20-50
DOOR OPENING TRIMpage 20-50
A.PILLAR TRIMpage 20-50
Removal/lnstallation, page 20 54
KICK PANELpage 20 50
DOOR SILL TRIMpage 20-50
Replacement,page 20-55
CARGO AREA FLOORpage 20-52
REAR CENTER SHELFpage 20-51
CARGO FLOOR MATpage 20-52
REAR TRIM PANELpage 20-52
20-49

Interior Trim
Trim Removal/lnstallation - Door Area
NOTE:. Put on gloves to protect your hands.. When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.. Take care not to bend or scratch the trim and panels.
1. Remove the trim as shown. To remove the door silltrim and B-pillar upper trim, remove the rear side trim panelas necessary (see page 20-51).
2. Installthe trim in the reverse order of removal, and note these items:
. Replace any damaged clips.. Apply liquid thread lock to the anchor bolts before reinstallatior,.. Before installing the anchor bolts, make sure there are no twists or kinks in the belts.
Fastener Locations
B>rClip,3 C>:Clip,?{White)
FRONT SEAT BELTUPPER ANCHOR BOLT7/16-20 UNF32 N m (3.3 kgf m,24 lbf.ft)
A-PILLAR TRIM
il-::7
/ ao----- LowER ANcHoR cAP
FRONT SEAT BELT LOWERANCHOR BOLT7/16-20 UNF32 N.m (3.3 kgt.m,24lbl.ftl
,"lF
{
A >: Clip,2(Black)
2ffi
Tl|t
\
KICK PANEL
REAR SIDE TRIM PANEL
20-50

Trim Removal/lnstallation - Rear Side Area
NOTE:. Put on gloves to protect your hands.. When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.. Take care not to bend or scratch the trim and panels.
'1. To remove the rear side trim panel, remove these items:
. Rear seat cushion and rear seat-back (see page 20-80). Cargo floor mat and cargo area floor (see page 20-52). Rear trim panel {see page20-52)
Remove the trim as shown. On the right side, disconnect the cargo compartment light connector.
Installthe trim in the reverse order of removal, and note these items:
. Replace any damaged clips.. Make sure the cargo compartment light connector is plugged in properly.
.lfthethreadsontherearsidetrimpanel mounting self-tapping ET screws are worn out, use an oversized self-
tapping ET screw (P/N 90137-S1A-Eo1 1) made specifically for this application.. When installing the rear side shelf, slip the rear seat belt through the slit in the trim.' Apply iiquid thread lockto the anchor bolts before reinstallation.. Before installing the anchor bolts, make sure there are no twists or kinks in the belt.
2.
3.
Fasten€r Locations
A>:Clip,11 B > rClip,2
SELF-TAIscREws5x0.8mm
{0.4 kgf m,3lbf.ft)
REAR BULKHEAOCOVER
TRIM
SIDE SHELF
REAR SEAT SELT
SIDE TRIM PANEL
SEATSTRIKER CAP
FRONT SEAT AELTLOWER ANCHOR BOLT7/16-20UNF32 N.m{3.3 kgf m,24lbt.tt)
c>rClap,l
-..:.:'
SILL TRIM
.F.-*-.n. \::: :\,/ I
,/ \*JREAR SEAT BELT LOWER \ANCHOF BOLT \7/16-20UNF \32 N m (3.3 kgf m, 24 lbf ft, \LOWERREAR SPEAKER COVERANCHOR CAP
20-51

lnterior Trim
Trim Removal/lnstallation - Cargo Floor Area
NOTE:. Put on gloves to protect your hands.
. When jrying with a flat-tip screwdriver, wrap it with protective tape to prevent damage'
. Take care notto bend or scratch the trim and panels.
1. To remove the rear trim panel, remove the child seat tether anchor (see page 23-11)'
2. Remove the trim as shown.
3. Installthe trim in the reverse order of removal, and replace any damaged clips'
Fastener Locations
A> : Clip,3 B> :
REAR SEAT-BACK COVER
To rear side trimpanel.
Clip.4
j-=ETr
FLOOR MAT
-t
CARGO AREA FLO
7
To rear sadetrim panel.
20-52
REAR TBIM PANEL