2003 HONDA CIVIC ERS

Fuel Supply System
{Fuel Pressure Regulator
Replacement
Remove the fuel pump (see page 1 1-153).
Remove the fuel pressure regulator (A).
Installthe part in the reverse order of removal witha new o-ring (B).
1.
2.
11-152
Fuel Filter Replacement
The fuel filter should be replaced whenever the fuelpressure drops belowthe specified value {270 320 kpa,2.8 3.3 kgf lcm', 40 47 psi), after making sure that thefuel pump and the fuel pressure regulator are OK.
1. Remove the fuel pump(seepagell-'153).
2. Remove the
Install in the reverse order of removalwith a new
base gasket (B) and a new o-ring (C), then check
these items:
' When connecting the wire harness, make sure
the connection is secure and the terminal (D) is
firmly locked into place.. When installing the fuel gauge sending unit iE),make sure the connection is secure and the
connector is firmly locked into place. Be carefulnot to bend or twist it excessively.
\
fuel filter (A).
@-to
ReIJ
e"^AR^ ...\e @n-)
gs
sg

Fuel Pump/Fuel Gauge Sending Unit Replacement
SpecialTools Required
Fuel sender wrench 07XAA-001010A
1.Relieve the fuel pressure (see page 11-144).
Remove the fuel fill cap.
Remove the seat cushion (see page 20-80).
Remove the access panel (A)from the floor.
5.
7.
Disconnect the fuel pump 5P connector (B).
Disconnect the quick-connect fitting {C) from the
fuel tank unit.
Using the special tool, loosen the fuel tank unit
locknut (A).
93 N.m19.5 kgf.m,69 lbf.ftl
11-153
8. Remove the locknut (A) andthefuel tankunit.
9. Remove the stopper {O). Release the hook (P) and
remove the fuel filter (B), the fuel gauge sending
unit (C). the case (D), the wire harness (E), and the
fuel pressure regulator (F).
10. When connecting the fuel tank unit, make sure the
connection is secure and the suction filter (G) is
firmly connected to the f uel pump (H).
11. Install the fuel tank unit in the reverse order of
removal with a new base gasket (l)and new o-rings
(J), then check these items:
. When connecting the wire harness, make sure
the connection is secure and the connector (K) is
firmly locked into the place.
. When installing the f uel gauge sending unit,
make sure the connection is secure and the
connector is firmly locked into place. Be careful
not to bend or twist the connector excessively.. When installing the fueltank unit, align the marks
(L) on the fuel tank (M) and the fuel tank unit (Ni

Fuel Supply System
Fuel Pulsation Damper Replacement
1. Relieve the fuel pressure(seepagell-144).
2. Remove the engine cover.
3. Remove the fuel rail mounting nuts from the fuelrail.
4. Remove the ground cable (G 101.
5. Raise the fuel rail.
6. Place awrench (A) onthefuel rail (B).
7. Place a wrench (C) onthefuel pulsation damper (D).
8. Remove the pulsation damper.
9. Installthe fuel pulsation damper in lhe reverse
order of removal with new washers.
NOTE:. Replace all washers wheneve r the fuel pulsation
damper is loosened or removed,. lf the drain hole (A) ofthefuel pulsationdamper
cover does not face bottom, reinstall it as shown.
11-154

Fuel Tank Replacement
Relievethefuel pressure (see page 11-144).
Drain the fuel tank: Remove the fuel pump (see page 1 1-153). Using a hand pump, hose, and container suitable for
gasoline. draw the fuel from the fuel tank.
Jack up the vehicle, and suppon it with safety stands.
Remove the fuel pipe cover (A). Disconnect the fuel vapor hose and quick-connect fittings.
Disconnect the hoses. Slide back the clamps (B), then twist the hoses as you pull to avoid damaging them.
A 38 N.m(3.9 ksf.m,28lbfft)
5. Place a jack or other support under the tank.
6. Removethe strap bolts, and letthestrap (C) hangfree.
7. Remove the fuel tank (D). lf itstickstothe undercoaton its mount, carefully pry itoffthe mount
8. Install the parts in the reverse order of removal.
1.
2.
3.
(}
\
11-155

Intake Air System
1. Remove the nuts (A) and the stud (B).
Air Cleaner Replacement
Remove the air cleaner (C).
Install in the reverse order of removal.
2.
3.
11-162
Air Cleaner Element Replacement
1. Disconnect the PCV hose 1A).
Open the air cleaner housing cover (B).
Remove the air cleaner (C) from the air cleaner
housing (D).
Install in the reverse order of removal.
2.
3.\,
4.
{0.3 kgf m,2lbf.ft)

Intake Air System
Throttle Cable Removal/lnstallation
1. Fully open the throttle valve, then remove the
throttle cable (A) from the throttle link (B).
Remove the cable housing (C)from the cable
bracket (D).
Remove the throttle cable (A)from the accelerator
pedal (B).
2.
3.
SILICONE GREASE B(P/N 08798-9002)
(P/N 08?98-9002)
11-164
5.
Install in the reverse order of removal.
After installing, start the engine. Hold the engine at
3,000 rpm with no load (in neutral) untilthe radiator
fan comes on, then let it idle.
Hold the cable, removing all slack from it.
Set the locknut on the cable bracket {A).Turn the adjusting nut (B) so that its free play is
0 mm.
The should beno crearance.
Remove the cable from the cable bracket (A). Set
the adjusting nut on the other side of the throttle
bracket, then tighten the locknut {C}.
With the cable properly adjusted, check the throttle
valve to be sure it opens fully when you push the
accelerator pedal to the floor. Also check the
throttle valve to be sure it returns to the idle
position whenever you release the accelerator
Deoat.
7.
!
8.
9.
('1.0 kgf.m,7.2 tbf.ftl

PCV Valve Inspection and Test
2.
1. Check the PCV valve (A), hoses {B), and
connections for leaks or restrictions.
At idle, make sure there is a clicking sound from the
PCV valve when the hose between the PCV valve
and intake manifold is lightly pinched {A)with your
fingers or pliers.
lf there is no clicking sound, check the PCV valve
grommet for cracks or damage. lf the grommet is
OK. reDlace the PCV valve and recheck.
PCV Valve Replacement
'LDisconnect the PCV hose.
Remove the PCV valve (A).
3. Install
with a
(4.5 kgf.m,33 lbf.ft)
the parts in the reverse order of removal
new gasket (B).
11-169

EVAP Canister Replacement
l. Remove the vacuum hoses (A).
2. Remove the boit (B).
3. Remove the EVAP canister (C).
4. Install in the reverse order of removal.
Fuel Tank Vapor Control Valve
Replacement
1. Remove the fuel tank(seepagell-155).
2. Remove the fueltank vapor control valve(A) from
the fuel tank (B).
Install the fuel tank vapor control valve.
Install the fuel tank (see page 1 'l -155).
3.
4,
11-189