2003 HONDA ACCORD COUPE air condition

µ
µ
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ì
Ì

Maint enance
6-cylinder Models
285
Canadian Owners U.S. Owners
A, B, C
AB
C
Use the Maintenance Schedule for Severe Conditions.
Refer to page to determine which schedule to use.
Service at the indicated distance or time, whichever comes first. Do the items in as required for each distance/time interval.
Replace engine oil.
Rotate tires (follow pattern on page336).
Replace engine oil filter.
Inspect front and rear brakes.
Check parking brake adjustment.
Inspect tie rod ends, steering gearbox and boots.
Inspect suspension components.
Inspect driveshaft boots.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks. Inspect exhaust system.
Inspect fuel lines and connections.
Replace air cleaner element (independent of time).
Inspect drive belt.
Replace dust and pollen filter.
Do items in A.
Do items in A, B.
Do items in A.
DoitemsinA,B,C.
Do items in A.
Replace brake fluid (independent of mileage).
Do items in A, B.
Do items in A.
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A. Replace brake fluid (independent of mileage).
DoitemsinA,B,C.
Do items in A. Replace timing belt, and inspect water pump.
Inspect valve clearance (independent of
time). Replace spark plugs (independent of time).
Do items in A, B.
Do items in A. Replace transmission fluid (A/T), then
replace every 90,000 mi/144,000 km/5 yrs. Replace transmission fluid (M/T).
DoitemsinA,B,C. Replace brake fluid (independent of mileage).
Replace engine coolant, then replace every
60,000 mi/96,000 km/5 yrs.
7,500 mi/12,000 km
15,000 mi/24,000 km/1 yr
22,500 mi/36,000 km
30,000 mi/48,000 km/2 yrs
37,500 mi/60,000 km
3yrs
45,000 mi/72,000 km/3 yrs
52,500 mi/84,000 km
60,000 mi/96,000 km/4 yrs
67,500 mi/108,000 km
75,000 mi/120,000 km/5 yrs
82,500 mi/132,000 km
6yrs
90,000 mi/144,000 km/6 yrs
97,500 mi/156,000 km
105,000 mi/168,000 km/7 yrs
112,500 mi/180,000 km
120,000 mi/192,000 km/6 yrs
120,000 mi/192,000 km/8 yrs
9yrs
120,000 mi/192,000 km/10 yrs
See information on maintenance and emissions warranty, last
column, page .
Check engine oil and coolant at each fuel stop.
Check and adjust valve clearance, cold engine, only if noisy. :
275
NOTE:
274
Maintenance Schedule for Normal Conditions (listed by distance/time)

µ
µ
Ì
Î
Î
Ì
Ì ÌÎ
Î
6-cylinder Models
Maint enance286
Visually inspect the following items:
Service at the indicated distance
or time whichever comes first.
miles x 1,000
km x 1,000
months
Every 3,750 miles (6,000 km) or 6 monthsCheck oil and coolant at each fuel stop
Inspect every 105,000 miles (168,000 km), otherwise adjust only if noisy Every 15,000 miles (24,000 km)
Every 105,000 miles (168,000 km)
120,000 miles (192,000 km) or 10 years, then every 60,000 miles (96,000 km) or 5 years
See dust and pollen filter on page for replacement information under special driving conditions. See timing belt on page to determine need for replacement.
See information on maintenance and emissions warranty, last column, page .
Tie rod ends, steering gear box, and boots
Suspension components
Driveshaft boots
Brake hoses and lines (including ABS)
All fluid levels and condition of fluids
Exhaust system
Fuel lines and connections
Lights and controls
vehicle underbody Every 7,500 miles (12,000 km) or 6 months
Rotate tires every 7,500 miles (12,000 km)
Replace engine oil and oil filter
Check engine oil and coolant
Replace air cleaner element
Use normal schedule except in dusty
conditions
Inspect valve clearance
Replace spark plugs Replace timing belt and inspect water pump
Inspect drive belt
Replace engine coolant
Replace transmission fluid
Inspect front and rear brakes
Replace brake fluid
Check parking brake adjustment
Replace dust and pollen filter
Lubricate all hinges, locks and latches
Rotate tires (Check tire inflation and condition at
least once per month) Every 3 years (independent of mileage)
Every 7,500 miles (12,000 km) or 6 months
At 60,000 miles (96,000 km) or 4 years, then every 30,000 miles (48,000 km) or 2 years 30
48
24
15
24
12 45
72
3675
120 60 105
168
84
90
144 72
Every 60,000 miles (96,000 km) or 3 years 60
96
48
120
192
96
At
:
1:
2: 275
332 330M/T
A/T
1
2
Maintenance Schedule for Severe Conditions

µ
µ
Ø
Ø
Ø
Ø Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
ÌÎ
Ì
Ì
Î
Ì
Î
Î
CONT INUED
Maint enance
6-cylinder Models
287
Canadian Owners U.S. Owners
A, B, C, D
AB
C
D E
Use the Maintenance Schedule for Severe Conditions.
Refer to page to determine which schedule to use.
Service at the indicated distance or time, whichever comes first. Do the items in as required for each distance/time interval.
3,750 mi/6,000 km
7,500 mi/12,000 km/6 mos
11,250 mi/18,000 km
15,000 mi/24,000 km/1 yr
18,750 mi/30,000 km
22,500 mi/36,000 km
26,250 mi/42,000 km
30,000 mi/48,000 km/2 yrs
33,750 mi/54,000 km
37,500 mi/60,000 km
41,250 mi/66,000 km
3yrs
45,000 mi/72,000 km/3 yrs
48,750 mi/78,000 km
52,500 mi/84,000 km
56,250 mi/90,000 km
60,000 mi/96,000 km/3 yrs
60,000 mi/96,000 km/4 yrs
63,750 mi/102,000 km Do item in A.
Do items in A, B.
Do item in A.
DoitemsinA,B,C.
Do item in A.
Do items in A, B.
Do item in A.
DoitemsinA,B,C,D.
Do item in A.
Do items in A, B.
Do item in A.
Replace brake fluid (independent of mileage).
DoitemsinA,B,C.
Do item in A.
Do items in A, B.
Do item in A. Replace transmission fluid (M/T).Replace timing belt.
Replace transmission fluid (A/T).
DoitemsinA,B,C,D.
Do item in A. Replace engine oil and filter.
Inspect front and rear brakes.
Rotate tires (follow pattern on page
336).
Inspect tie rod ends, steering gearbox and boots.
Inspect suspension components.
Inspect driveshaft boots.
Check parking brake adjustment.
Replace air cleaner element (independent of time).
Lubricate all hinges, locks and latches with
multipurpose grease.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks. Inspect exhaust system.
Inspect fuel lines and connections.
Check all lights.
Inspect the underbody.
Inspect drive belt.
Replace air cleaner element (independent of time).
Replace dust and pollen filter.
Replace air cleaner element every 15,000 mi/24,000 km
(independent of time), otherwise use normal
conditions schedule.
274
1
2
See dust and pollen filter on page for replacement information under special driving
conditions. See timing belt on page to determine need for replacement.See information on maintenance and emissions warranty, last
column, page .
Check engine oil and coolant at each fuel stop.
Check and adjust valve clearance, cold engine, only if noisy.
NOTE: :
1:
2:
332
330
275
Maintenance Schedule for Severe Conditions (listed by distance/time)

Run the air conditioning at least once
a week during the cold weather
months. Run it f or at least ten
minutes while you are driving at a
steady speed with the engine at
normal operating temperature. This
circulates the lubricating oil con-
tained in the ref rigerant.
Your car’s air conditioning is a sealed
system. Any major maintenance,
such as recharging, should be done
by a qualif ied mechanic. You can do
a couple of things to make sure the
air conditioning works ef f iciently.
Periodically check the engine’s
radiator and air conditioning
condenser f or leaves, insects, and
dirt stuck to the f ront surf ace. These
block the air f low and reduce cooling
ef f iciency. Use a light spray f rom a
hose or a sof t brush to remove them.
If the air conditioning does not get as
cold as before, have your dealer
check the system. Recharge the
system with Ref rigerant HFC-134a
(R-134a). (See Specif ications on
pages and .)
396 398
A ir Condit ioning Syst em
Maint enance329
AIR CONDITIONING CONDENSER
Whenever you have the air conditioning
system serviced, make sure the service
f acility uses a ref rigerant recycling
system. This system captures the
ref rigerant f or reuse. Releasing
ref rigerant into the atmosphere can
damage the environment.
The condenser and radiator f ins bend
easily. Only use a low-pressure spray
or sof t-bristle brush to clean them.

The dust and pollen f ilter is located
behind the glove box.Open the glove box.
To replace it: Push the stop on the right side of
the glove box to detach it from the
glove box.
Pivot the glove box out of the way.
The dust and pollen f ilter removes
pollen and dust that is brought in
f rom the outside through the heating
and cooling system/climate control
system.
This f ilter should be replaced every
30,000 miles (48,000 km) under
normal conditions. It should be
replaced every 15,000 miles (24,000
km) if you drive primarily in urban
areas that have high concentrations
of soot in the air f rom industry and
diesel-powered vehicles. Replace it
more of ten if air f low f rom the
heating and cooling system/climate
control system becomes less than
usual.
1.3. 2.
Dust and Pollen Filter
Maint enance
Replacement
330
STOP

Use a gauge to measure the air
pressure at least once a month. Even
tires that are in good condition may
lose one to two psi (10 to 20 kPa, 0.1
to 0.2 kgf /cm ) per month.
Remember to check the spare tire at
thesametimeyoucheckallthe
other tires.
Check the pressure in the tires when
they are cold. This means the car
has been parked f or at least three
hours. If you have to drive the car
bef ore checking the tire pressure,
the tires can still be considered
‘‘cold’’ if you drive less than 1 mile
(1.6 km).
Keeping the tires properly inf lated
provides the best combination of
handling, tread lif e, and riding
comf ort. Underinf lated tires wear
unevenly, adversely af f ect handling
and f uel economy, and are more
likely to f ail f rom being overheated.
Overinf lated tires can make your car
ride more harshly, are more prone to
damage f rom road hazards, and wear
unevenly.
We recommend that you visually
check your tires every day. If you
think a tire might be low, check it
immediately with a tire gauge.
To saf ely operate your car, your tires
must be the proper type and size, in
good condition with adequate tread,
and correctly inf lated. The f ollowing
pages give more detailed inf ormation
on how and when to check air
pressure, how to inspect your tires
for damage and wear, and what to do
when your tires need to be replaced.
Add or release air, if needed, to
match the recommended cold tire
pressures on page .334
CONT INUED
Inf lation
Tires
Maint enance333
Using tires that are excessively
worn or improperly inflated can
cause a crash in which you can
be seriously hurt or killed.
Follow all instructions in this
owner’s manual regarding tire
inflation and maintenance.

Î
Î
Î
ÎÎ
Î
If you check the pressure when the
tires are hot [the car has been driven
several miles (kilometers)], you will
see readings 4 to 6 psi (30 to 40 kPa,
0.3to 0.4 kgf /cm ) higher than the
cold reading. This is normal. Do not
let air out to match the specif ied cold
pressure. The tire will be
underinf lated.
Youshouldgetyourowntire
pressure gauge and use it whenever
you check your tire pressures. This
will make it easier f or you to tell if a
pressure loss is due to a tire problem
and not due to a variation between
gauges.
The following chart shows the
recommended cold tire pressures f or
most normal driving conditions and
speeds. Tire pressures f or high
speed driving are the same as f or
normal driving. Thecompactsparetirepressureis:
For convenience, the recommended
tire sizes and cold air pressures are
on a label on the driver’s doorjamb.
For additional technical information
about your tires, see page .
Tubeless tires have some ability to
self -seal if they are punctured.
However, because leakage is of ten
very slow, you should look closely
for punctures if a tire starts losing
pressure.
400Tire Size Cold Tire Pressure
for Normal Driving
Tire Size Cold Tire Pressure for Normal Driving
Front:
Rear:
Front:
Rear:
EX-V6 with M/T EX, LX-V6 and EX-V6 with A/T
1
2
All models
4-cylinder LX model
All models except 4-cylinder LX
Tires
Maint enance
Recommended T ire Pressures f or
Normal Driving
334
60 psi (420 kPa , 4.2 kgf/cm)
P205/60R16 91V
P215/50R17 93V 32 psi (220 kPa ,
2.2 kgf/cm
)
30 psi (210 kPa , 2.1 kgf/cm
)
29 psi (200 kPa , 2.0 kgf/cm
)
P205/65R15 92H 30 psi (210 kPa ,
2.1 kgf/cm
)
29 psi (200 kPa , 2.0 kgf/cm
)
1
2
1
2

Every time you check inf lation, you
should also examine the tires f or
damage, f oreign objects, and wear.
Youshouldlookfor:Bumps or bulges in the tread or
side of the tire. Replace the tire if
youfindeitherof theseconditions.
Cuts, splits, or cracks in the side
of the tire. Replace the tire if you
can see f abric or cord.
Excessive tread wear. In addition to proper inf lation,
correct wheel alignment helps to
decrease tire wear. If you f ind a tire
is worn unevenly, have your dealer
check the wheel alignment.
The tires were properly balanced by
the factory. They may need to be
rebalanced at some time bef ore they
are worn out. Have your dealer
check the tires if you f eel a consis-
tent vibration while driving. A tire
should always be rebalanced if it is
removed f rom the wheel f or repair.
Your car’s tires have wear indicators
molded into the tread. When the
tread wears down to that point, you
will see a 1/2 inch (12.7 mm) wide
band running across the tread. This
shows there is less than 1/16 inch
(1.6 mm) of tread lef t on the tire. A
tire that is this worn gives very little
traction on wet roads. You should
replace the tire if you can see the
tread wear indicator in three or more
places around the tire.
CONT INUED
Inspection
Maintenance
Tires
Maint enance335
INDICATOR LOCATION MARKS
TREAD WEAR INDICATORS