2003 HONDA ACCORD COUPE clock

CONT INUED
Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
3. 2.
4. 5.
Lights
Maint enance343
6-cylinder modelsAIR INTAKE
COVER
FASTENERS
4-cylinder models6-cylinder models
TAB BULB
TABBULB

Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
Reinstall the air intake duct
securely.
Put the inner f ender cover in place.
Install the two holding clips. Lock
each one in place by pushing on
the center.
Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
If you need to change the low
beam headlight bulb on the driver’s
side, remove the air intake duct.
You can reach the air intake duct
fromthebacksideof theinner
f ender.
6. 5. 7.
8.
9.
10.
11.
4.
On EX-V6 model with manual
transmission
On EX-V6 model with manual transmission
Maint enance
Lights
345
AIR INTAKE DUCT
EX-V6 with M/T

If you are changing the bulb on
the passenger’s side, start the
engine, turn the steering wheel all
the way to the left, and turn off the
engine. If you are changing the
bulb on the driver’s side, turn the
steering wheel to the right.Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
1.
3.
2.
4.
Maint enance
Lights
Replacing a Front T urn Signal/
Parking/Side Marker Light Bulb
346
HOLDING CLIPS

Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Install the new bulb in the socket.
Turn it clockwise to lock it in place. Remove the burned out bulb f rom
thesocketbypushingitinand
turning the bulb counterclockwise
until it unlocks.
Put the inner f ender cover in place.
Install the holding clips. Lock each
oneinplacebypushingonthe
center. Turn on the lights to make sure
the new bulb is working.
5.
6.
7.
8.
9.
Lights
Maint enance347

Open the trunk.
Remove the light assembly cover
by pulling its outside edge.Determine which of the three
bulbs is burned out: stop/taillight/
side marker, back-up or turn
signal.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Turn on the lights to make sure
the new bulb is working.
Install the light assembly cover.
Make sure it snaps into place.
1. 3. 2.
4.
5.
6.
7.
Lights
Maint enance
Replacing Rear Bulbs
348
COVER

Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb in the socket.Reinstall the socket. Turn it clock-
wise until it locks.
Turn on the lights to make sure
the new bulb is working.
1. 2. 3.
4.
Replacing a High-mount Brake
Light Bulb
Lights
Maint enance350
BULB
SOCKET

Turn the jack’s end bracket
counterclockwise to loosen it, then
remove the jack.Loosen the f ive wheel nuts 1/2
turn with the wheel wrench.
The jack is behind a cover in the
right f ender. Remove the cover by
turning the handle counterclock-
wise, then pulling on the cover.
6.
7.8.
T aking Care of t he Unexpect ed
Changing a Flat T ire
366
JACK
WHEEL WRENCHWHEEL NUT

CONT INUED
Use the extension and wheel
wrench as shown to raise the car
until the f lat tire is of f the ground.
Locate the jacking point nearest
thetireyouneedtochange.Place
the jack under the jacking point.
Turn the end bracket clockwise
until the top of the jack contacts
the jacking point. Make sure the
jacking point tab is resting in the
jack notch. Remove the wheel nuts, then
remove the f lat tire. Temporarily
place the f lat tire on the ground
with the outside surface of the
wheel f acing up. You could scratch
the wheel if you put it f ace down.
9.
10.
11.
Changing a Flat T ire
T aking Care of t he Unexpect ed367
JACKING POINT WHEEL WRENCH
EXTENSION