2003 FORD MUSTANG oil

13. Remove the self-
adjusting mechanism.
14. Remove the self- adjusting mechanism shaft bushings.
Installation 1. NOTE: Before the installation of the clutch pedal shaft or clutch pedal, remove and inspect the
brake and clutch pedal bushings. Clean and lubricate with a light film of engine oil meeting Ford
specification WSS- M2C153-G and replace the brake and clutch pedal bushing if excessive wear
is evident.
To install, reverse the removal procedure. Klj . 4 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

9 7N232 Gear shift plate
10 7K201 Gear selector interlock sleeve
11 305078-
S Pin
12 7302 Selector body
13 7230 Gear shifter fork 3-
4 shift 14 7160 Output shaft bearing snap ring
15 7117 Second speed synchronizer thrust washer
16 7175 First and second gear synchronizer inner cone
17 7174 First and second gear synchronizer outer cone
18 7107 Synchronizer blocking ring
19 7A044 Synchronizer hub insert (also part of 7124)
20 7K218 First and second speed synchronizer hub ball
21 7061 Output shaft assembly
22 7109 Synchronizer hub insert spring (also part of
7124)
23 7124 Sleeve (also part of 7061)
24 7173 First gear bearing spacer
25 7127 First gear bearing
26 7100 First gear
27 7065 Output shaft rear bearing
28 7D234 Thrust bearing
29 7D235 Thrust washer
30 — Synchronizer hub (part of 7124)
31 7124 Synchronizer assembly
32 7B340 Third gear
33 7B369 Third speed bearing
34 7B320 Third speed gear bearing spacer
35 7064 Snap ring
36 7119 Thrust washer
37 7102 Second gear
38 7728 Second speed gear bearing spacer
39 7693 Countershaft front bearing seal
40 7F431 Countershaft bearing assembly
41 7113 Countershaft cluster gear
42 7L172 Countershaft rear bearing adjustment shim
43 7195 Countershaft rear bearing retainer
44 7C210 Bolt
45 7144 Fifth speed cluster gear
46 7M000 Reverse brake ring
47 7G042 Thrust washer
48 7059 Fifth speed synchronizer retaining snap ring
49 7L276 Oil pick-
up funnel Klj . 3 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Seal
Removal 1. With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. CAUTION: Index- mark the driveshaft flange and pinion flange, and the driveshaft
slip yoke and transmission output shaft.
Remove the driveshaft. For additional information, refer to Section 205 - 01 .
3. Using the special tools, remove the extension housing fluid seal.
Installation 1. Using the special tool, install the extension housing fluid seal.
SECTION 308-
03A: Manual Transaxle/Transmission — T5OD 2003 Mustang Workshop Manual Special Tool(s)
Installer, Transmission
Extension Housing Oil Seal
308-
227 (T94P-7657- A) Slide Hammer
100-
001 (T50T-100- A) Remover, Bushing
307-
001 (TOOL- 1175-AC) or
Equivalent Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

29. Apply a 3.2-
mm (1/8-in) bead of silicone rubber to the sealing surface on the extension housing.
30. Install the detent ball, the shifter detent spring, and the gearshift offset lever. 1. Coat the shifter detent spring with petroleum jelly and install it in the gearshift offset lever.
2. Lubricate the detent plate and install the detent ball in the neutral position on the plate.
3. Position the gearshift offset lever in the extension housing with the gear shift interlock
spring over the detent ball.
31. CAUTION: To prevent component damage, the alignment tab on the reverse brake
ring must align with the alignment slot in the extension housing.
NOTE: Verify that the oil pick- up funnel engages the fifth gear synchronizer.
Slide the gearshift offset lever and the extension housing into place as an assembly. Press
downward on the gearshift offset lever to compress the shifter interlock spring and push the
gearshift offset lever and extension housing into place. Klj . 10 ba
142003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Seal
Removal 1. With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. CAUTION: Index- mark the driveshaft flange and pinion flange, and the driveshaft
slip yoke and transmission output shaft.
Remove the driveshaft. For additional information, refer to Section 205 - 01 .
3. Using the special tools, remove the extension housing fluid seal.
Installation 1. Using the special tool, install the extension housing fluid seal.
SECTION 308-
03B: Manual Transaxle/Transmission — TR3650 2003 Mustang Workshop Manual Special Tool(s)
Installer, Transmission
Extension Housing Oil Seal
308-
227 (T94P-7657- A) Slide Hammer
100-
001 (T50T-100- A) Remover, Bushing
307-
001 (TOOL- 1175-AC) or
Equivalent Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

ASSEMBLY
Transmission
1. Lubricate all components with transmission fluid during assembly.
2. Attach the clutch housing to the special tool.
SECTION 308-
03B: Manual Transaxle/Transmission — TR3650 2003 Mustang Workshop Manual Special Tool(s)
Dial Indicator Gauge with
Holding Fixture
100-
002 (TOOL- 4201-C) or
equivalent Holding Fixture, Transmission
307-
003 (T57L- 500-B) Remover/Installer, Bearing
Tube
308-
024 (T75L-7025- B) Replacer/Adapter
308-
239 (T96P-7025- A) Installer, Transmission
Extension Housing Oil Seal
308-
227 (T94P-7657- A)
Material Item Specification
Motorcraft MERCON® Multi-
Purpose (ATF) Transmission
Fluid
XT
-2-QDX MERCON
Premium Long Life Grease
XG
-1-C, K or T ESA-
M1C75-
B Klj . 1 ba
192003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

GENERAL PROCEDURES
Transmission Draining and Filling
1. Remove the drain plug and drain the transmission. zPosition a suitable drain pan under the transmission.
2. Clean and install the drain plug.
3. NOTE: Before removing, clean the area around the filler plug.
Remove the filler plug.
4. Using a suitable oil suction gun, fill the transmission to the correct level with the specified fluid. zTransmission capacity is 3.9 liters (4.1 quarts).
SECTION 308-
03C: Manual Transaxle/Transmission — T56 2003 Mustang Workshop Manual Material
Item Specification
DEXRON III® (
ATF)
Transmission Fluid
XT -2-QDX DEXRON III® Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES
Input Shaft and Bearing
Disassembly and Assembly
SECTION 308-
03C: Manual Transaxle/Transmission — T56 2003 Mustang Workshop Manual Special Tool(s)
Plate, Bearing/Oil Seal
205-
090 (T75L-1165- B) Puller, Bearing
205-
D064 (D84L-1123- A) Installer, Drive Pinion Bearing
Cone
205-
004 (T53T-4621- B) Adapter Set, Step Plate
205-
DS011 (D80L-630- A) Universal Puller Set
303-
DS005 (D80L-100- A) Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...