2003 FORD MUSTANG engine

10. Disconnect the EGR tube from the EGR valve.
11. Disconnect the positive crankcase ventilation (PCV) hose from the base of the throttle body.
12. Remove the PCV valve and hose as an assembly.
13. Remove the engine wiring harness. Klj . 4 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

14. Disconnect the vacuum line from the fuel pressure sensor. Item Part Number Description
1 — To crankshaft position sensor
2 — To A/C compressor
3 — To radio ignition interference capacitor (2)
4 — To fuel injectors (8)
5 — To ignition coils (8)
6 — To engine coolant temperature sensor
7 — To throttle position sensor
8 — To idle air control valve
9 — To EGR vacuum regulator
10 — To differential pressure feedback EGR
11 — To fuel pressure regulator
12 — Fuel injection ground
13 — To generator
14 — To camshaft position sensor
15 — To body
16 — To heated oxygen sensor (2)
17 — Engine bulkhead connector
18 — To low coolant sensor
19 — To body
20 — To power distribution box
21 — To body Klj . 5 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

27.
CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other
abrasive means to clean sealing surfaces. These tools will cause scratches and gouges
which make leak paths.
Clean the sealing surfaces.
28. Remove the coolant bypass tube. 1. Remove the nut.
2. Remove the coolant bypass tube.
29. Remove the RH engine mount. Klj . 9 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

30.
NOTE: LH shown; RH similar.
Using a suitable container, drain coolant from the engine block. zInstall the drain plugs when finished.
31. Remove the four bolts and the power steering pump.
RH cylinder head 32. Remove the RH exhaust manifold. 1. Remove the RH exhaust manifold nuts.
2. Remove the RH exhaust manifold.
3. Remove the RH exhaust manifold gasket and discard. Klj . 10 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

43. Using the special tool, remove the crankshaft pulley.
44. Remove the coolant pump pulley.
1. Remove the coolant pump pulley bolts.
2. Remove the coolant pump pulley.
45. Remove the bolts and belt idler pulleys.
46. Using the special tool, remove the engine front cover seal. Klj . 14 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

47. Remove the bolts.
48. Remove the bolts, the studs, and the engine front cover.
zDiscard the gaskets, clean and inspect the sealing surfaces.
CAUTION: Since the engine is not free- wheeling, if the crankshaft or the camshafts are
moved in any manner during removal and installation, the crankshaft and the camshafts must
be re- synchronized. 49. Remove the crankshaft sensor ring from the crankshaft. Klj . 15 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

55.
NOTE: The hydraulic lash adjusters must be reinstalled in their original locations. Record the
hydraulic lash adjuster locations.
Remove the hydraulic lash adjusters.
RH cylinder head 56. CAUTION: The cylinder head must be cool before removing it from the engine.
Cylinder head warpage can result if a warm or hot cylinder head is removed.
CAUTION: Place clean shop towels over exposed engine cavities. Carefully remove
the towels so foreign material is not dropped into the engine.
CAUTION: The cylinder head bolts must be discarded and new bolts installed. They
are tighten- to-yield designed and cannot be reused.
CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other
abrasive means to clean the sealing surfaces. These tools cause scratches and gouges
that make leak paths. Use a plastic scraping tool to remove all traces of the head gasket.
CAUTION: Aluminum surfaces are soft and can be scratched easily. Never place the
cylinder head gasket surface, unprotected, on a bench surface.
Remove the bolts and the RH cylinder head.
zDiscard the cylinder head gasket.
z Discard the cylinder head bolts. Klj . 18 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

LH cylinder head
57. CAUTION: The cylinder head must be cool before removing it from the engine.
Cylinder head warpage can result if a warm or hot cylinder head is removed.
CAUTION: Place clean shop towels over exposed engine cavities. Carefully remove
the towels so foreign material is not dropped into the engine.
CAUTION: The cylinder head bolts must be discarded and new bolts installed. They
are tighten- to-yield designed and cannot be reused.
CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other
abrasive means to clean the sealing surfaces. These tools cause scratches and gouges
that make leak paths. Use a plastic scraping tool to remove all traces of the head gasket.
CAUTION: Aluminum surfaces are soft and can be scratched easily. Never place the
cylinder head gasket surface, unprotected, on a bench surface.
Remove the bolts and the LH cylinder head.
zDiscard the cylinder head gasket.
z Discard the cylinder head bolts. Klj . 19 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...