2003 FORD MUSTANG test G

port. DISCARD the leaking
parts, and INSTALL a new
component.
z Vehicles with a
plastic intake
manifold. z
Acceptable condition. Some
plastic manifolds exhibit this
noise, which is the effect of
the plastic manifold.
z Automatic
transmission buzz or
hiss z
Incorrect
driveline
angles. z
CHECK for correct driveline
angles. REPAIR as
necessary. REFER to
Section 205 - 00 .
z Worn or
damaged main
control
solenoids or
valves. z
Using a transmission tester,
activate the solenoids to
duplicate sound. INSTALL
new components as
necessary. REFER to
Section 307 - 01 .
z Manual Transmission
Clutch throw- out
bearing whine. A
change in noise pitch
or loudness while
depressing the clutch
pedal z
Worn throw- out
bearing. z
INSTALL a new throw- out
bearing. REFER to Section 308 - 01 .
z Heating, vacuum and
air conditioning
(HVAC) system chirp
— most audible inside
the vehicle. Listen for
a change in noise
pitch or loudness
while changing the
HVAC system blower
speed z
Damaged or
worn HVAC
blower bearing. z
INSTALL a new blower
motor. REFER to Section 412 - 02 .
z Air conditioning (A/C)
clutch ticking —
occurs when the
compressor clutch
engages z
Acceptable
noise.
z Incorrect air
gap. z
LISTEN to the clutch to
determine if the noise occurs
with clutch engagement. A
small amount of noise is
acceptable. If the noise is
excessive, CHECK the A/C
clutch air gap. INSPECT the
A/C clutch for wear or
damage. INSTALL a new
clutch as necessary. REFER
to Section 412 - 03 .
z Intermittent rattle, or
scraping/rubbing
noise z
Loose exhaust
heat shield(s). z
INSPECT the exhaust
system for loose parts using
a glove or clamps to verify
cause. REPAIR as
necessary. REFER to
Section 309 - 00 .
z Wiring, hose or
other part
interfering with
accessory drive
belt or pulley. z
INSPECT accessory drive
system closely verifying
there is adequate clearance
to all rotating components.
REPAIR as necessary.
z Engine ticking or
knocking noise —
occurs during idle or z
Piston noise or
valvetrain noise
(bled down z
Go To Pinpoint Test G . Klj . 30 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

high idle during the
first cold start of the
day
lifter/lash
adjuster).
z A continuous, speed-
dependent rattle from
the engine — occurs
during idle or high idle
during the first cold
start of the day and
disappears as the
engine warms up z
Piston noise or
valvetrain noise
(bled down
lifter/lash
adjuster). z
Go To Pinpoint Test G .
z Idle vibration—a low-
frequency vibration (5-
20 Hz) or mild shake
that is felt through the
seat/floorpan z
Cylinder misfire. zUsing a scan tool, CHECK
the ignition system. CARRY
OUT a cylinder power test.
REFER to Section 303 - 00 .
z Engine or
torque
converter out of
balance. z
VERIFY the torque
converter to crankshaft pilot
clearance is correct,
REPAIR as necessary. RE-
INDEX the torque converter
on the flex plate by 120° on
a 3 bolt converter or 180° for
a 4 bolt converter. REFER to
Section 307 - 01 . RETEST
the vehicle.
z Idle vibration—a high-
frequency vibration
(20–80 Hz) or buzz,
that is felt through the
steering wheel or seat z
Exhaust system
mounts bound
up. z
VERIFY concern occurs at
engine firing frequency.
CHECK that the exhaust
system vibrates at the same
frequency as the engine.
ADD 9– 14 km (20–30 lb.) to
the tail pipe to test, CARRY
OUT Exhaust System Neutralizing in this section.
z Body mounts
loose. z
INSPECT the body mounts.
REPAIR as necessary.
z Power steering
lines grounded
out. z
INSPECT that the power
steering lines are not
contacting the chassis or
each other. REPAIR as
necessary. Symptom Chart—
Squeak and Rattle Condition
Possible Sources Action
z Squeak— heard
inside the vehicle
when
closing/opening
the door z
Insufficient
lubrication on
the door hinge
or check strap. z
LUBRICATE the hinge or check
strap.
z Internal door
components
loose, rubbing or
misaligned. z
CHECK the inside of the door.
TIGHTEN or ALIGN as
necessary. USE the Rotunda
Squeak and Rattle Kit to isolate
any rubbing components.
z Squeak— heard
inside the vehicle
when z
Worn or
damaged glass
run/channel. z
REPAIR or INSTALL a new
glass run/channel. REFER to
Section 501 - 11 . Klj . 31 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

closing/opening
the window
z Squeak— heard
outside of vehicle
when
closing/opening
the door z
Exhaust shield
rubbing against
the chassis or
exhaust pipe. z
CHECK the exhaust system.
REPAIR as necessary. REFER
to Section 309 - 00 .
z Squeak— occurs
with initial brake
pedal application z
Disc brake pads. zUnder certain conditions,
asbestos free pads can
generate a squeak noise. This
noise is normal and does not
indicate a concern.
z Squeak— a
constant noise
that occurs with
brake pedal
applications z
Damaged or
worn disc brake
pads. z
INSPECT the pads for oil,
grease or brake fluid
contamination. CHECK for
glazed linings. A brake disc with
hard spots will also cause a
squeak type noise. REPAIR or
INSTALL new pads as
necessary. REFER to Section 206 - 03 for front disc brakes and
Section 206 - 04 for rear disc
brakes.
z Squeak— noise
occurs over
bumps or when
turning z
Worn control
arm bushings. z
INSPECT the control arm
bushings. Spray with lubricant
and CARRY OUT a "bounce
test" to determine which
bushing. REPAIR as necessary.
REFER to Section 204 - 01 .
z Worn or
damaged shock
absorber/strut. z
INSPECT the shock absorber
for damage. CARRY OUT a
"bounce test" to isolate the
noise. INSTALL a new shock
absorber/strut as necessary.
REFER to Section 204 - 01 for
the front shock absorber/strut or
Section 204 - 02 for the rear
shock absorber/strut.
z Rattle— heard
when
closing/opening
the door or
window z
Loose internal
door
mechanism,
bracket or
attachment. z
REPEAT the motion or CARRY
OUT a "tap test" to duplicate the
noise. INSPECT the door for
loose components. TIGHTEN
loose components or USE the
Rotunda Squeak and Rattle Kit
to isolate any rattling
components.
z Rattle — GT
models only,
noise occurs from
the rear of the
vehicle z
A loose or under
torqued shock
damper
attaching nut. z
VERIFY the torque on the
shock damper- to-axle nuts is 63
Nm (46 lb- ft). VERIFY the
torque for the shock damper- to-
rail bracket nuts is 90 Nm (66
lb- ft). Do not over torque.
TIGHTEN as necessary.
z Squeak or rattle—
heard inside the
vehicle over rough
roads/bumps z
Misaligned glove
compartment
door/hinge. z
ALIGN the glove compartment
door.
z Instrument panel
trim loose or z
INSPECT the instrument panel
trim for missing or loose clips or Klj . 32 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

misaligned.
screws. REPAIR as necessary.
z Loose interior
component or
trim. z
CARRY OUT a "touch test".
ELIMINATE the noise by
pressing or pulling on interior
trim and components. USE the
Rotunda Squeak and Rattle Kit
to isolate any rattling/squeaking
components.
z Squeak or rattle—
noise with a
vibration concern z
Damaged or
worn body
mounts. z
INSPECT the upper and lower
absorbers and washers for
damage or wear. CHECK the
body mount brackets for
damage. CHECK the nuts and
bolts are tightened to
specifications. TIGHTEN as
necessary.
z Damaged or
worn sub- frame
mounts. z
INSPECT the upper and lower
absorbers for damage or wear.
CHECK the sub- frame for
damage. CHECK the nuts and
bolts are tightened to
specifications. TIGHTEN as
necessary. Symptom Chart—
Steering Noise/Vibration Condition
Possible Sources Action
z Steering grunt or
shudder — occurs
when turning into
or out of a turn at
low speeds
(temperature
sensitive) z
Steering gear or power
steering hoses. z
GO to Steering Gear
Grunt/Shudder Test
component test in this
section.
z Steering System
clonk— hydraulic
knocking sound z
Air in the steering
hydraulic system. z
CHECK for leaks in the
system. PURGE the air
from the system.
REFER to Section 211 -
00 .
z Power steering
pump moan —
loud humming
noise occurs when
the steering wheel
is rotated to the
stop position.
Produces a 120-
600 Hz frequency
that changes with
rpm z
Power steering hose
grounded out to
chassis. z
INSPECT the power
steering hoses. REPAIR
as necessary.
z Aerated fluid. zCHECK for leaks in the
system. PURGE the air
from the system.
REFER to Section 211 -
00 .
z Steering gear isolators. zINSPECT the isolators
for wear or damage.
REPAIR as necessary.
z Low fluid. zCHECK the fluid level. Klj . 33 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REFILL as necessary.
z Power steering pump
brackets loose or
misaligned. z
CHECK bolts, brackets
and bracket alignment.
TIGHTEN bolts to
specification. REPAIR
or INSTALL new
brackets as necessary.
REFER to Section 211 -
02 .
z Steering gear clunk
— occurs only
while cornering
over a bump (can
be temperature
sensitive) z
Steering gear. zINSPECT the steering
gear for loose mounting
bolts. TIGHTEN as
necessary. REFER to
Section 211 - 02 .
z Feedback (rattle,
chuckle or
knocking noise in
the steering gear)
— a condition
where roughness is
felt in the steering
wheel when the
vehicle is driven
over rough
surfaces z
Column
intermediate/flexible
shaft joints damaged or
worn. z
INSTALL a new
intermediate/flexible
shaft. REFER to Section 211 - 04 .
z Loose, damaged or
worn tie- rod ends. z
TIGHTEN the nuts to
specification or
INSTALL new tie- rod
ends as necessary.
REFER to Section 211 -
02 .
z Steering gear
insulators or mounting
bolts loose or
damaged. z
TIGHTEN the bolts or
INSTALL new bolts as
necessary. REFER to
Section 211 - 02 .
z Steering column
intermediate shaft bolts
are loose. z
TIGHTEN the bolts to
specification. REFER to
Section 211 - 04 .
z Steering column
damaged or worn. z
REPAIR or INSTALL a
new steering column as
necessary. REFER to
Section 211 - 04 .
z Loose suspension
bushings, bolts or ball
joints. z
INSPECT the
suspension system.
TIGHTEN or INSTALL
new components as
necessary. REFER to
Section 204 - 01 .
z Feedback (nibble
at the steering
wheel) — a
condition where
slight rotational
movement is felt in
the steering wheel
when the vehicle is
driven over rough
or grooved z
Lateral runout in the
tire or wheel. z
GO to Pinpoint Test H . Klj . 34 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Clunk— noise from the
front suspension, occurs
in and out of turns z
Loose front
struts or shocks. z
INSPECT for loose nuts
or bolts. TIGHTEN to
specifications. REFER to
Section 204 - 01 .
z Clunk— noise from the
rear suspension, occurs
when shifting from
reverse to drive z
Loose rear
suspension
components. z
INSPECT for loose or
damaged rear
suspension components.
REPAIR or INSTALL
new components as
necessary. REFER to
Section 204 - 02 .
z Click or pop— noise from
the front suspension.
More noticeable over
rough roads or over
bumps z
Worn or
damaged ball
joints. z
CARRY OUT a ball joint
inspection. INSTALL
new ball joints or control
arms as necessary.
REFER to Section 204 -
01 .
z Click or pop (FWD
vehicles)—noise occurs
when vehicle is turning z
Worn or
damaged ball
joints. z
CARRY OUT a ball joint
inspection. INSTALL
new ball joints or control
arms as necessary.
z Click or snap— occurs
when accelerating around
a corner z
Damaged or
worn outboard
CV joint. z
INSPECT the outboard
CV joint and boot.
REPAIR or INSTALL a
new CV joint as
necessary.
z Front suspension noise—
a squeak, creak or rattle
noise. Occurs mostly over
bumps or rough roads z
Steering
components.
z Loose or bent
front struts or
shock
absorbers.
z Damaged
spring or spring
mounts.
z Damaged or
worn
control/radius
arm bushings.
z Worn or
damaged
stabilizer bar
bushings or
links. z
Go To Pinpoint Test H .
z Rear suspension noise—
a squeak, creak or rattle
noise. Occurs mostly over
bumps or rough roads z
Loose or bent
rear shock
absorbers.
z Damaged
spring or spring
mounts.
z Damaged or
worn control
arm bushings.
z Worn or
damaged
stabilizer bar
bushings or
links. z
Go To Pinpoint Test I .
z Shudder— occurs during zRear drive axle zCHECK the axle mounts Klj . 37 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

acceleration from a slow
speed or stop
assembly
mispositioned. and the rear suspension
for damage or wear.
REPAIR as necessary.
z Incorrect or high
CV joint
operating angle. z
CHECK vehicle ride
height is within limits.
REPAIR as necessary.
z Damaged or
worn front
suspension
components. z
CHECK for a loose
stabilizer bar, damaged
or loose strut/strut
bushings or loose or
worn ball joints.
INSPECT the steering
linkage for wear or
damage. REPAIR or
INSTALL new
components as
necessary.
z Shimmy—most
noticeable on
coast/deceleration. Also
hard steering condition z
Excessive
positive caster. z
CHECK the caster
alignment angle.
CORRECT as
necessary. REFER to
Section 204 - 00 .
Symptom Chart—
Tire Noise/Vibration Condition
Possible Sources Action
z Tire noise— hum/moan
at constant speeds z
Abnormal wear
patterns. z
SPIN the tire and CHECK
for tire wear. INSTALL a
new tire as necessary.
INSPECT for
damaged/worn suspension
components. CARRY OUT
wheel alignment.
z Tire noise— noise tone
lowers as the vehicle
speed is lowered z
Out-of- balance
tire. z
BALANCE the tire and
road test. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Tire noise — ticking
noise, changes with
speed z
Nail puncture or
stone in tire
tread. z
INSPECT the tire. REPAIR
as necessary.
z Wheel and tire—
vibration and noise
concern is directly
related to vehicle
speed and is not
affected by
acceleration, coasting
or decelerating z
Damaged or
worn tire. z
Go To Pinpoint Test J .
z Tire wobble or
shudder — occurs at
lower speeds z
Damaged wheel
bearings. z
SPIN the tire and CHECK
for abnormal wheel
bearing play or roughness.
ADJUST or INSTALL new
wheel bearings as
necessary. REFER to
Section 204 - 01 .
z Damaged wheel. zINSPECT the wheel for
damage. INSTALL a new
wheel as necessary.
REFER to Section 204 -Klj . 38 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

01 .
z Damaged or
worn suspension
components. z
INSPECT the suspension
components for wear or
damage. REPAIR as
necessary.
z Loose wheel
nuts. z
CHECK the wheel nuts.
TIGHTEN to specification.
REFER to Section 204 -
04 .
z Damaged or
uneven tire wear. z
SPIN the tire and CHECK
for abnormal tire wear or
damage. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Tire shimmy or
shake— occurs at
lower speeds z
Wheel/tire out of
balance. z
BALANCE the wheel/tire
assembly.
z Uneven tire wear. zCHECK for abnormal tire
wear. INSTALL a new tire
as necessary. REFER to
Section 204 - 04 .
z Excessive radial
runout of wheel
or tire. z
CARRY OUT a radial
runout test of the wheel
and tire. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Worn or
damaged wheel
studs or
elongated stud
holes. z
INSPECT the wheel studs
and wheels. INSTALL new
components as necessary.
REFER to Section 204 - 01
for the front wheels or
Section 204
- 02 for the rear
wheels.
z Excessive lateral
runout of the
wheel or tire. z
CARRY OUT a lateral
runout test of the wheel
and tire. CHECK the
wheel, tire and hub.
REPAIR or INSTALL new
components as necessary.
z Foreign material
between the
brake disc and
hub or in the
brake disc fins. z
CLEAN the mounting
surfaces of the brake disc
and hub. CHECK the
brake disc fins for material.
z High speed shake or
shimmy—occurs at
high speeds z
Excessive wheel
hub runout.
z Damaged or
worn tires.
z Damaged or
worn wheel
bearings.
z Worn or
damaged
suspension or
steering linkage
components.
z Brake disc or
drum imbalance. z
Go To Pinpoint Test K . Klj . 39 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...