2003 FORD MUSTANG seats

4. Position the halfshaft for installation.
5. Seat the CV joint stub shaft in the differential side gear.
1. Slide the stub shaft into the axle housing until the shaft splines are past the differential seal.
2. Remove the special tool.
3. Align the stub shaft splines and the side gear splines, and slide the stub shaft into the gear until it seats.
„When seated, the axle circlip will lock the stub shaft in the differential side gear.
Check the circlip engagement by attempting to pull the inboard CV joint out of the
differential side gear. If the circlip has not seated, push the CV joint inward until
the circlip is fully engaged in the differential side gear.
6. Connect the axle shaft to the hub. 1. Making sure the serrations on the shaft line up with the serrations in the hub, install the axle shaft into the hub.
2. Install a new retainer. Do not tighten the retainer at this time. Klj . 6 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Supplemental Restraint System (SRS) Deactivation and
Reactivation
Deactivation
WARNING: Always wear safety glasses when repairing an air bag supplemental restraint
system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury
in the event of an accidental deployment.
WARNING: After deployment, the air bag surface can contain deposits of sodium
hydroxide, a product of the gas generant combustion that is irritating to the skin. Wash your
hands with soap and water afterwards.
WARNING: Never probe the connectors on the air bag module. Doing so can result in air
bag deployment, which can result in personal injury.
WARNING: Air bag modules with discolored or damaged trim covers must be installed
new, not repainted.
WARNING: The restraint system diagnostic tool is for restraint system service only.
Remove from vehicle prior to road use. Failure to remove could result in injury and possible
violation of vehicle safety standards.
1. WARNING: To avoid accidental deployment and possible personal injury, the
backup power supply must be depleted before repairing or replacing any front or side air
bag supplemental restraint system (SRS) components and before servicing, replacing,
adjusting or striking components near the front or side air bag sensors, such as doors,
instrument panel, console, door latches, strikers, seats and hood latches.
Please refer to the appropriate vehicle shop manual to determine location of the front air
bag sensors.
The side air bag sensors are located at or near the base of the B- pillar.
To deplete the backup power supply energy, disconnect the battery ground cable and
wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped). SECTION 211-
04: Steering Column 2003 Mustang Workshop Manual Special Tool(s)
Diagnostic Tool, Restraint
System (2 Req'd)
418-
F088 (105- R0012) Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
excessive connecting rod bearing clearance
Valve Train Analysis— Engine Off—Valve Cover Removed
Check for damaged or severely worn parts and correct assembly. Make sure correct parts are used
with the static engine analysis as follows.
Valve Train Analysis— Engine Off, Rocker Arm
z Check for loose mounting bolts, studs and nuts.
z Check for plugged oil feed in the rocker arms (6564) or cylinder head.
Valve Train Analysis— Engine Off, Camshaft Roller Followers and Hydraulic Lash Adjusters,
Overhead Camshaft
zCheck for loose mounting bolts on camshaft carriers.
z Check for plugged oil feed in the camshaft roller followers, lash adjusters or cylinder heads.
Valve Train Analysis— Engine Off, Camshaft— Engines
z Check for broken or damaged parts.
Valve Train Analysis— Engine Off, Push Rods
z Check for bent push rods (6565) and restricted oil passage.
Valve Train Analysis— Valve Springs
z Check for broken or damaged parts.
Valve Train Analysis— Engine Off, Valve Spring Retainer and Valve Spring Retainer Keys
z Check for correct seating of the valve spring retainer key (6518) on the valve stem and in valve
spring retainer (6514).
z Check for correct seating on the valve stem.
Valve Train Analysis— Engine Off, Valves and Cylinder Head
z Check for plugged oil drain back holes.
z Check for worn or damaged valve tips.
z Check for missing or damaged guide- mounted valve stem seal.
z Check collapsed valve tappet gap.
z Check installed valve spring height.
z Check for missing or worn valve spring seats.
z Check for plugged oil metering orifice in cylinder head oil reservoir (if equipped).
Static checks (engine off) are to be made on the engine prior to the dynamic procedure. Klj . 14 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9. Install the valve covers.
Valve Train Analysis— Engine Running, Camshaft Lobe Lift— Push Rod Engine
Check the lift of each lobe in consecutive order and make a note of the readings. 1. Remove the valve covers.
2. Remove the rocker arm seat bolts, rocker arm seat (6A528) and rocker arms.
Typical Engine With Push Rods
3. Make sure the valve tappet is seated against camshaft (6250). Install (1) Dial Indicator Gauge with Holding Fixture so the ball socket adapter of the indicator is on top of the valve tappet or (2)
Dial Indicator Gauge Adapter is on top of push rod and in same plane as valve tappet push rod
movement.
4. Remove the spark plugs.
5. Connect an auxiliary starter switch in the starting circuit. Crank the engine with ignition switch in OFF position. Bump crankshaft over until valve tappet is on base circle of camshaft lobe. At this
point, valve tappet will be in its lowest position. If checking during engine assembly, turn
crankshaft using a socket or ratchet.
6. Zero the dial indicator. Continue to rotate crankshaft slowly until valve tappet is in fully- raised
position (highest indicator reading).
7. NOTE: If lift on any lobe is below specified service limits, install a new camshaft, and new valve
tappets.
Remove the Dial Indicator with Holding Fixture, Dial Indicator Gauge Adapter, and auxiliary
starter switch.
8. Install rocker arm seats, rocker arms and rocker arm seat bolts.
9. Install valve covers.
10. Install spark plugs.
Valve Train Analysis— Engine Running, Valve Tappet
Valve tappet noise can be caused by any of the following:
zexcessive valve tappet gap (collapsed) Klj . 16 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Valve —
Seat Inspection
Valve and Seat Refacing Measurements
CAUTION: After grinding valves or valve seats, check valve clearance.
1. Check the valve head and seat. zCheck valve angles.
z Check margin width.
z Refer to the appropriate section in Group 303 for the procedure.
z Be sure margin width is within specification.
2. Inspect for abnormalities on the valve face and seat.
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Valve —
Seat Width
1. Measure the valve seat width. If necessary, grind the valve seat to specification. zMeasure the intake valve seat width.
z Measure the exhaust valve seat width.
z Recheck the valve spring installed length after the seats have been ground, and shim the
valve springs as necessary to achieve the correct installed spring length.
z Refer to the appropriate section in Group 303 for the procedure.
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES
Cylinder Head
Disassembly and Assembly
CAUTION: If the components are to be reinstalled, they must be installed in the same
position. Mark the components removed for location.
1. Remove the spark plugs (12405) if necessary.
2. Using the special tool, compress the valve springs (6513).
3. Remove the following: 1. The valve spring retainer key (6518).
2. The valve spring retainers (6514).
3. The valve springs (6513).
4. The valve stem seals and seats (6A517).
SECTION 303-
01A: Engine — 3.8L 2003 Mustang Workshop Manual Special Tool(s)
Compressor, Valve Spring
303-
163 (T81P-6513- A)
Material Item Specification
SAE 5W-
20 Premium Synthetic
Blend Motor Oil
XO- 5W20-QSP or equivalent WSS-
M2C153-
H Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
SECTION 303-
01D: Engine — Mach I 4.6L (4V) 2003 Mustang Workshop Manual General Specifications
Item Specification
Metal Surface Cleaner
F4AZ-
19A536- RA WSE-
M5B392- A Silicone Gasket and Sealant F7AZ-19554-
EA WSE-
M4G323-
A4 Motorcraft Premium Gold Engine Coolant VC-7-
A (in Oregon VC-7-B) (Yellow
Color) WSS-
M97B51- A1 Pipe Sealant with Teflon® D8AZ-19554-
A WSK-
M2G350-
A2 Motorcraft MERCON® Super Premium 5W-
20 Motor Oil XO-5W20-QSP WSS-
M2C153- H Threadlock 262 E2FZ-19554-
B WSK-
M2G351-
A6
Engine Specifications Description Specification
GENERAL SPECIFICATIONS
Displacement 4.6L (4V) (281 CID)
Number of Cylinders 8
Bore and Stroke 90.2 x 90.0 mm (3.55 x 3.54 inch)
Firing Order 1-3-7-2-6-5-4-
8 Oil Pressure (HOT 1500 RPM) 138-
310 kPa Drive Belt Tension a
Combustion Chamber Volume (cc)
52.6±
0.5 cm c Valve Seats
·
Width— Intake 1.8-
2.2 mm (0.071- 0.086 inch) ·
Width— Exhaust 1.8-
2.2 mm (0.071- 0.086 inch) ·
Angle 45 degrees
·
Runout (T.I.R.) Max 0.05 mm (0.002 inch)
Valve Arrangement (Front-
to-Rear) c ·
(Left Hand) Intake: S-P-S-P-S-P-S-P
·
Exhaust: E-E-E-E-E-E-E-E
·
(Right Hand) Intake: P-S-P-S-P-S-P-S
·
Exhaust: (C) E-E-E-E-E-E-E-E
Valve Stem to Guide Clearance
·
Intake 0.020-
0.069 mm (0.00078- 0.00272 inch) ·
Exhaust 0.046-
0.095 mm (0.0018- 0.0037 inch) Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...