2003 FORD MUSTANG oil

information, REFER to
Section 205
- 00 .
REPAIR as necessary.
z Transmission
rumble/growl— noise at
all speeds in forward
gears, more
pronounced in a heavy
acceleration condition z
Damaged or worn
transmission
bearing or gears
(high mileage
vehicles). z
CHECK transmission
fluid for excessive
metal particles.
REPAIR as necessary.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Transfer case whine—
noise at all ranges z
Incorrect fluid level
or fluid quality. z
CHECK that the
transfer case is filled to
the correct level and
with the specified fluid.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Worn oil pump. zDISASSEMBLE the
transfer case. CHECK
the oil pump for wear or
damage. REPAIR as
necessary.
z Under- inflated or
oversized tires. z
CONFIRM that the tires
and wheels are correct
for the vehicle. CHECK
that the tire inflation
pressures are correct.
z Transfer case
growl/rumble— noise at
all ranges (A small
amount of planetary
noise can be heard
when the transfer case
is operated in low
range.) z
Damaged or worn
bearings or
planetary gear. z
DISASSEMBLE the
transfer case. CHECK
the bearings or
planetary gear for wear
or damage. REPAIR as
necessary.
z Transfer case
scraping/grating—
noise at all ranges z
Excessively
stretched drive
chain hitting the
case. z
DISASSEMBLE the
transfer case. CHECK
the drive chain for wear
or damage. REPAIR as
necessary.
z Transfer case
howl/hum— noise at all
ranges or high range
only z
Worn or damaged
sun (input) gear,
clutch pack
(intermediate) gear
or output shaft gear. z
DISASSEMBLE the
transfer case. CHECK
the gears for wear or
damage. REPAIR as
necessary.
z Transfer case
howl/hum— noise at
low range only z
Worn or damaged
intermediate gear
and sliding gears
(clutch pack). z
DISASSEMBLE the
transfer case. CHECK
the gears for wear or
damage. REPAIR as
necessary.
z Transfer case
vibration— vibration felt
with vehicle in 4WD z
Transfer case
mounting.
z Driveshaft out of
balance.
z Excessive pinion z
Go To Pinpoint Test M . Klj . 44 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Is the ticking noise gone? CHECK for TSB for applicable vehicle.
REPAIR as necessary. TEST the system
for normal operation.
No
GO to
B2 .
B2 CHECK FOR TICKING NOISE AT THE FUEL
INJECTOR z
Using an EngineEAR, listen at the fuel
injectors by placing a probe on each injector.
To isolate the faulty injector, disconnect the
injector electrical connector and listen for the
noise.
z Is the fuel injector the source of the ticking
noise? Yes
INSTALL a new fuel injector. REFER to
Section 303
- 04A for 3.8L engines or
Section 303 - 04B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B3 .
B3 CHECK THE BELT TENSIONER FOR TICKING
NOISE z
Inspect the accessory drive. Check for the belt
tensioner bottoming at end of travel or not at
end of stroke.
z Using an EngineEAR, listen at the belt
tensioner.
z Is the belt tensioner the source of the
noise? Yes
INSTALL a new belt tensioner. TEST the
system for normal operation.
No
GO to
B4 .
B4 CHECK THE WATER PUMP FOR TICKING
NOISE z
Using an EngineEAR, listen at the water pump
for ticking noise.
z Is the water pump the source of the noise? Yes
INSTALL a new water pump. REFER to
Section 303
- 03A . TEST the system for
normal operation.
No
GO to B5 .
B5 CHECK FOR AN OBSTRUCTION OF THE
COOLING FAN z
Inspect the cooling fan for obstructions.
z Check the cooling fan and shroud for wear or
damage.
z Was there an obstruction or does the
cooling fan show signs of damage? Yes
REPAIR or INSTALL a new cooling fan.
REFER to
Section 303 - 03A . TEST the
system for normal operation.
No
GO to B6 .
B6 CHECK THE OIL PUMP FOR TICKING NOISE
z
Check the oil pump using EngineEARs and
probe at the oil filter adapter to verify the oil
pump as a source.
z Is the oil pump the source of the noise? Yes
INSTALL a new oil pump. REFER to
Section 303
- 01A for 3.8L engines or
Section 303 - 01B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B7 .
B7 CHECK VALVE LIFTERS OR LASH
ADJUSTERS FOR CORRECT OPERATION z
Check valve lifter/lash adjuster for correct
operation, using EngineEARs.
z Are the valve lifters/lash adjusters Yes
VERIFY customer concern. CONDUCT a
diagnosis of other suspect components. Klj . 50 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Suspension System
Inspection and Verification
1. Road test. zVerify the customer's concern by performing a road test on a smooth road.
2. Inspect tires. zCheck the tire pressure with all normal loads in the vehicle and the tires cold. For
additional information, refer to the vehicle certification (VC) label.
z Verify that all tires are sized to specification.
z Inspect the tires for incorrect wear and damage.
3. Inspect chassis and underbody. zRemove any excessive accumulation of mud, dirt or road deposits from the chassis and
underbody.
4. Inspect for aftermarket equipment. zCheck for aftermarket changes to the steering, suspension, wheel and tire components
(such as competition, heavy duty, etc.) The specifications shown in this manual do not
apply to vehicles equipped with aftermarket equipment.
5. Inspect shock absorbers. All vehicles are equipped with gas- pressurized hydraulic shock absorbers. These shock
absorbers are not adjustable or refillable and cannot be repaired.
zOil Leak: A light film of oil (weepage) on the upper portion of the shock absorber is
permissible and is a result or correct shock lubrication. Weepage is a condition in which a
film of oil accumulates on the thin tube (body) and is normally noticed due to the
collection of dust in this area. If shock absorbers exhibit this weepage condition, they are
functional units and new shock absorbers should not be installed. Leakage is a condition
in which the entire shock absorber body is covered with oil and the oil will drip from the
shock absorber onto the pavement. If condition exists:
„Make sure fluid observed is not from sources other than the shock absorber.
„ Install a new shock absorber, if necessary.
z Vehicle Sag: Many times new shock absorbers are installed in an effort to solve a vehicle
sag concern. Shock absorbers by design are hydraulic damping units only and, unlike
suspension springs, do not support any suspension loads. Therefore, installing a new
shock absorber will not correct a vehicle sag concern.
z Installment in Pairs: In the past it was recommended that new shock absorbers be
installed in pairs if one unit became unrepairable. New shock absorbers no longer need
to be installed in pairs when only one unit is not repairable.
SECTION 204-
00: Suspension System — General Information 2003 Mustang Workshop Manual Visual Inspection Chart
Mechanical Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. If an obvious cause for an observed or reported condition is found, correct the cause (if
possible) before proceeding to the next step.
7. If the fault is not visually evident, determine the symptom and GO to Symptom Chart .
Symptom Chart z
Front wheel bearing(s)
z Loose or damaged front or rear suspension components
z Loose, damaged or missing suspension fastener(s)
z Damaged spring(s)
z Damaged or leaking strut and spring assemblies
z Damaged or leaking shock absorber(s)
z Worn or damaged suspension bushing(s)
z Loose, worn or damaged steering system components
z Damaged axle components
Symptom Chart Condition
Possible Sources Action
z Dogtracking zExcessive rear
thrust angle. z
CHECK the wheel alignment.
ADJUST as necessary.
z Front or rear
suspension
components. z
INSPECT the front and rear
suspension system. REPAIR
or INSTALL new suspension
components as necessary.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Drive axle
damaged. z
REPAIR as necessary. Refer
to the appropriate section in
Group 205 for the procedure..
z Drift/pull zUnequal tire
pressure. z
ADJUST tire pressure.
z Excessive side-to-
side difference in
caster or camber. z
CHECK the wheel alignment.
ADJUST as necessary.
z Tire forces. zROTATE tires front to rear.
z Unevenly loaded or
overloaded vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Steering
components. z
REFER to Section 211 - 00 .
z Brake drag. zREFER to Section 206 - 00 .
z Front bottoming
or riding low z
Strut(s). zINSTALL new strut(s) as
necessary. REFER to Section 204 - 01 .
z Front coil springs
(5310). z
CHECK ride height. INSTALL
new springs as necessary.
REFER to Section 204 - 01 .
z Incorrect tire
wear z
Incorrect tire
pressure (rapid
center rib or inner
and outer edge
wear). z
ADJUST tire pressure. Klj . 2 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Excessive front or
rear toe (rapid inner
or outer edge
wear). z
CHECK the wheel alignment.
ADJUST as necessary.
z Excessive negative
or positive camber
(rapid inner or outer
edge wear). z
CHECK the wheel alignment.
ADJUST as necessary.
z Tires out of balance
(tires cupped or
dished). z
BALANCE tires.
z Rough ride zStrut(s). zINSTALL new strut(s) as
necessary. REFER to Section 204 - 01 .
z Shock absorber(s). zINSTALL new shock absorber
(s) as necessary.
z Front coil springs or
rear springs (5560). z
INSTALL new front coil
springs or rear springs as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Shimmy or
wheel tramp z
Loose wheel nut(s). zTIGHTEN to specification.
REFER to Section 204 - 04 .
z Loose front
suspension
fasteners. z
TIGHTEN to specification.
REFER to Section 204 - 01 .
z Front wheel bearing
(s). z
REFER to Wheel Bearing Inspection in this section.
z Wheel or tire
runout. z
REFER to Section 204 - 04 .
z Tire flatspotting. zREFER to Section 204 - 04 .
z Shock absorber(s). zINSTALL new shock absorber
(s) as necessary.
z Loose, worn or
damaged ball joint
(s). z
GO to the Ball Joint Inspection
component test in this section.
z Loose, worn or
damaged steering
components. z
REFER to Section 211 - 00 .
z Front wheel
alignment. z
CHECK the wheel alignment.
ADJUST as necessary.
z Sticky steering,
poor returnability z
Ball joints. zGO to the Ball Joint Inspection
component test in this section.
z Steering
components. z
REFER to Section 211 - 00 .
z Steering wheel
off- center z
Unequal front or
rear toe settings
(side-to- side). z
CHECK the wheel alignment.
ADJUST as necessary.
z Steering
components. z
REFER to Section 211 - 00 .
z Sway or roll zOverloaded,
unevenly or
incorrectly loaded
vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Loose wheel nut(s). zTIGHTEN to specification. Klj . 3 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REFER to
Section 204 - 04 .
z Strut(s). zINSTALL new strut(s) as
necessary. REFER to Section 204 - 01 .
z Shock absorber(s). zINSTALL new shock absorber
(s) as necessary.
z Loose front
stabilizer bar (5482)
or rear stabilizer
bar (5A772). z
TIGHTEN to specification.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Worn stabilizer
assembly bushing
(s). z
INSTALL new bushing(s) as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Front coil spring(s)
or rear spring(s). z
INSTALL new front coil
springs or rear springs as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Vehicle leans to
one side z
Unevenly loaded or
overloaded vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Front or rear
suspension
components. z
INSPECT the front and rear
suspension system. REPAIR
or INSTALL new suspension
components as necessary.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Front coil springs or
rear springs. z
INSTALL new front coil
springs or rear springs as
necessary. REFER to Section 204 - 01 or
Section 204 - 02 .
z Incorrect ride
height. Lateral tilt
out of specification. z
CHECK ride height. INSTALL
new front coil springs or rear
springs as necessary. REFER
to Section 204 - 01 or
Section 204 - 02 .
z Vibration/noise zTire or wheel
runout.
z Tire flatspotting.
z Wheel bearings.
z Wheel hubs.
z Brake components.
z Suspension
components.
z Steering
components. z
REFER to Section 100 - 04 .
z Wander zUnevenly loaded or
overloaded vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Ball joint(s). zGO to the Ball Joint Inspection
component test in this section.
z Front wheel bearing
(s). z
REFER to Wheel Bearing Inspection in this section.
z Loose, worn or
damaged
suspension
components(s). z
INSTALL new suspension
components as necessary.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Loose suspension
fasteners. z
TIGHTEN to specification.
REFER to Section 204 - 01 or
Section 204 - 02 . Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Remove the front coil spring (5310). For additional information, refer to
Spring in this section.
7. Remove the nut and the front suspension lower control arm. Discard the nut.
Installation 1. To install, reverse the removal procedure.
2. Check wheel alignment. Adjust if necessary. For additional information, refer to Section 204 - 00 . Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Spring
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number or an equivalent part must be installed, if installation is necessary. Do
not use a part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to ensure proper retention of these parts.
1. Mark the front shock absorber (18124) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
3. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
4. Remove the cotter pin and nut. Discard the cotter pin.
SECTION 204-
01: Front Suspension 2003 Mustang Workshop Manual Special Tool(s)
Tie-
Rod End Remover
211- 001 (TOOL- 3290-D) or
Equivalent Coil Spring Compressor
204-
D001 (D78P-5310- A) or
Equivalent Klj . 1 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...