2003 FORD MUSTANG engine oil

GENERAL PROCEDURES
Hydro-
Boost Bleeding
1. NOTE: The Hydro- Boost power brake booster (2B560) is generally self- bleeding, and the
following procedure will normally bleed the air from the power brake booster. Normal operation
of the vehicle will further remove any additional trapped air.
Fill the power steering oil reservoir (3A697) with MERCON® Multi- Purpose ATF XT-2-QDX or
MERCON® equivalent.
2. Remove the powertrain control module (PCM) fuse to prevent the engine from starting.
3. Crank the engine for several seconds.
4. Check the fluid level in the power steering oil reservoir and add if necessary. Install the powertrain control module (PCM) fuse.
5. Start the engine.
6. With the engine running, turn the steering wheel (3600) from stop- to-stop twice. Turn the engine
off.
7. Depress the brake pedal (2455) several times to discharge the accumulator.
8. Repeat Steps 5 and 6.
9. If foaming occurs, stop the engine and allow the foam to dissipate.
10. Repeat Steps 5 and 6 as required, until all the air is removed from the system (when the foaming stops).
SECTION 206-
07: Power Brake Actuation 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
System Flushing —
CII Power Steering Pump
WARNING: Do not mix oil types. Any mixture or any unapproved oil can lead to seal
deterioration and leaks. A leak can ultimately cause loss of fluid, which can result in a loss of
power steering assist.
1. Remove the fuel pump fuse from the battery junction box.
2. Disconnect the power steering return hose. Plug the reservoir.
3. Attach an extension hose between the power steering return hose and an empty container.
4. Raise the front wheels off the floor. For additional information, refer to Section 100 - 02 .
5. Check the fluid level. If necessary, fill the reservoir to the correct level. zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
6. CAUTION: Do not crank the engine for more than 15 seconds at a time. Allow the
starter to cool for 1 minute before cranking again. Premature starter failure can occur.
CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump will occur.
Turn the steering wheel from stop- to-stop while cranking the engine until the fluid exiting the
power steering return hose is clear of all contamination and foreign material.
zAdd Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent as
needed.
7. Lower the vehicle.
8. Disconnect the extension hose from the power steering return hose. Remove the plug. Attach the power steering return hose to the reservoir.
SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
System Flushing —
CIII Power Steering Pump
WARNING: Do not mix oil types. Any mixture or any unapproved oil can lead to seal
deterioration and leaks. A leak can ultimately cause loss of fluid, which can result in a loss of
power steering assist.
1. Remove the fuel pump fuse from the battery junction box.
2. Disconnect the power steering return hose. Plug the reservoir.
3. Attach an extension hose between the power steering return hose and an empty container.
4. Raise the front wheels off the floor. For additional information, refer to Section 100 - 02 .
5. Check the fluid level. If necessary, fill the reservoir to the correct level. zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
6. CAUTION: Do not crank the engine for more than 15 seconds at a time. Allow the
starter to cool for 1 minute before cranking again. Premature starter failure can occur.
CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump could occur.
Turn the steering wheel from stop- to-stop while cranking the engine until the fluid exiting the
power steering return hose is clear of all contamination and foreign material.
zAdd Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent as
needed.
7. Lower the vehicle.
8. Disconnect the extension hose from the power steering return hose. Remove the plug. Attach the power steering return hose to the reservoir.
SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Fill
1. WARNING: Do not mix oil types, any mixture or any unapproved oil can lead to seal
deterioration and leaks. A leak can ultimately cause loss of fluid, which can result in a
loss of power steering assist.
Check the fluid level. If necessary, fill the reservoir to the correct level.
zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
2. Remove the fuel pump fuse from the battery junction box.
3. Raise the front wheels off the floor. For additional information, refer to Section 100 - 02 .
4. CAUTION: Do not crank the engine for more than 15 seconds at a time. Allow the
starter to cool for 1 minute before cranking again. Premature starter failure can occur.
CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump will occur.
Turn the steering wheel from stop- to-stop while cranking the engine.
5. Lower the vehicle.
6. CAUTION: Do not overfill the reservoir.
Check the fluid level. If necessary, fill the reservoir to the correct level. zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
7. Install the fuel pump fuse.
SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual General Specifications
Item Specification
Lubricants and Sealants
SAE 5W-
20 Premium Synthetic Blend Motor Oil
XO- 5W20- QSP WSS-
M2C153- H Diesel engine oil Refer to owner literature
Gasoline Engine Oil Dye
164-
R3705 ESE-
M99C103-B1 Threadlock® 262
E2FZ-
19554- B WSK-
M2G351- A6 Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Engine
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Special Tool(s)
Commercially Available
Leakdown Tester
—
Quick Disconnect Compression
Tester
134-
R0212 or equivalent Dial Indicator Gauge Adapter
303-
007 (TOOL- 6565-AB) or
equivalent Dial Indicator Gauge with
Holding Fixture
100-
002 (TOOL- 4201-C) or
equivalent Engine Cylinder Leak
Detection/Air Pressurization Kit
014-00708 or equivalent
Oil Pressure Gauge
303-
088 (T73L-6600- A) UV Leak Detector Kit
164-
R0756 or equivalent Vacuum/Pressure Tester
164-
R0253 or equivalent Klj . 1 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Inspection and Verification
1. Verify the customer concern by operating the engine to duplicate the condition.
2. Visually inspect for obvious signs of mechanical damage. Refer to the following chart.
3. If the inspection reveals obvious concerns that can be readily identified, repair as necessary.
4. If the concerns remain after the inspection, determine the symptoms. GO to Symptom Chart .
Symptom Chart Material
Item Specification
Gasoline Engine Oil
Dye
164-
R3705 or
equivalent ESE-
M99C103- B1 Engine Oil Refer to owner
literature
Visual Inspection Chart Mechanical
z
Engine coolant leaks
z Engine oil leaks
z Fuel leaks
z Damaged or severely worn parts
z Loose mounting bolts, studs and nuts
Symptom Chart Condition
Possible Sources Action
z Difficult
starting z
Damaged ignition
system. z
Refer to the appropriate section
in Group 303 for the procedure.
REFER to the Powertrain
Control/Emissions Diagnosis
(PC/ED) manual.
z Damaged fuel
system. z
Refer to the appropriate section
in Group 303 for the procedure.
REFER to the Powertrain
Control/Emissions Diagnosis
(PC/ED) manual.
z Damaged starting
system. z
Refer to the appropriate section
in Group 303 for the procedure. Klj . 2 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

(PC/ED) manual.
z Damaged valve
tappet or lash
adjuster. z
INSTALL a new valve tappet or
lash adjuster.
z Damaged valve
tappet guide or
valve tappet. z
INSTALL a new valve tappet
guide or valve tappet.
z Burnt or sticking
valve. z
REPAIR or INSTALL a new
valve.
z Weak or broken
valve spring. z
INSTALL a new valve spring.
z Carbon
accumulation in
combustion
chamber. z
ELIMINATE carbon buildup.
z Excessive oil
consumption z
Leaking oil. zREPAIR oil leakage.
z Malfunctioning PCV
system. z
REPAIR or INSTALL new
necessary components.
z Worn valve stem
seal. z
INSTALL a new valve stem seal.
z Worn valve stem or
valve guide. z
INSTALL a new valve and valve
guide.
z Sticking piston
rings. z
REPAIR or INSTALL new piston
rings.
z Worn piston ring
groove. z
INSTALL a new piston and
piston pin.
z Worn piston or
cylinder. z
REPAIR or INSTALL a new
piston or cylinder block.
z Engine noise zLeaking exhaust
system. z
REPAIR exhaust leakage.
z Incorrect drive belt
tension. z
REFER to Section 303 - 05 .
z Malfunctioning
generator bearing. z
Refer to the appropriate section
in Group 414 for the procedure.
z Malfunctioning
water pump
bearing. z
REFER to Section 303 - 03A .
z Malfunctioning or
damaged cooling
system. z
REFER to Section 303 - 03A .
z Malfunctioning or
damaged fuel
system. z
Refer to the appropriate section
in Group 303 for the procedure.
REFER to the Powertrain
Control/Emissions Diagnosis
(PC/ED) manual.
z Loose timing
chain/belt (6268). z
ADJUST or INSTALL a new
timing chain/belt.
z Damaged timing
chain tensioner
(6L266). z
INSTALL a new timing chain
tensioner.
z Excessive main
bearing clearance. z
ADJUST clearance or INSTALL
a new crankshaft main bearing
(6333). Klj . 4 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...