2003 FORD MUSTANG engine oil

z
If equipped, inspect automatic transmission fluid level with dipstick.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new cabin air filter.
z If filled with green engine coolant, change coolant.
224,000 Km (140,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
232,000 Km (145,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
240,000 Km (150,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect exhaust system and heat shields.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new engine air filter.
z Install a new fuel filter. (See ADDITIONAL INFORMATION below.)
z If equipped, install a new cabin air filter.
z If filled with yellow engine coolant, change coolant or at 8 years, whichever comes first.
z Change automatic transmission/transaxle fluid and filter.
z Change rear axle lubricant on all rear wheel (RWD) vehicles.
z Install a new accessory drive belt(s) (if a new belt has not been installed within the last 100,000
miles).
z If equipped, install new climate controlled seat filters (Navigator, Lincoln LS and Aviator).
ADDITIONAL INFORMATION: If vehicle is registered in California, the California Air Resources Board
(CARB) has determined that failure to install a new fuel filter at this interval will not nullify the emission
warranty or limit recall liability prior to completion of the vehicle's useful life. It is, however
recommended that maintenance checks be carried out and recorded at the indicated intervals.
Additional checks for natural gas and propane vehicles include inspecting fuel tanks, as well as
draining and installing a new filter. Klj . 9 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

CARRY OUT a driveline
vibration test. REFER to
Section 205
- 00 . REPAIR as
necessary.
z Binding or
damaged
splines on the
driveshaft slip-
yoke. z
CLEAN and INSPECT the
splines of the slip- yoke,
driveshaft and coupling
shaft for wear or damage.
INSTALL a new slip- yoke or
driveshaft assembly as
necessary. REFER to
Section 205 - 01 . REPAIR as
necessary.
z Driveshaft
runout. z
CARRY OUT a Runout
Check. REFER to Section 205 - 00 . REPAIR as
necessary.
z Incorrect lateral
and radial
tire/wheel
runout. z
INSPECT the tire and
wheels. MEASURE tire
runouts. REPAIR or
INSTALL new components
as necessary. REFER to
Section 204 - 04 .
z Driveline angles
out of
specification. z
CHECK for correct driveline
angles. REPAIR as
necessary. REFER to
Section 205 - 00 .
z Incorrectly
seated CV joint
in the front
wheel hub. z
CHECK the outer CV joint
for correct seating into the
hub. REPAIR as necessary. Symptom Chart —
Engine Noise/Vibration Condition
Possible Sources Action
z Grinding noise—
occurs during
engine cranking z
Incorrect starter
motor mounting. z
INSPECT the starter motor
for correct mounting.
REPAIR as necessary.
REFER to Section 303 - 06 .
z Starter motor. zCHECK the starter motor.
REPAIR or INSTALL a new
starter motor as necessary.
REFER to Section 303 - 06 .
z Incorrect starter
motor drive
engagement. z
INSPECT the starter motor
drive and flexplate/flywheel
for wear or damage.
INSTALL a new starter
motor drive or flywheel as
necessary. REFER to
Section 303 - 06 .
z Engine ticking
noise z
Fuel injector.
z Fuel line.
z Oil pump.
z Valve lifter.
z Belt tensioner.
z Water pump.
z Obstruction of cooling
fan. z
Go To Pinpoint Test B .
z Engine drumming zPowertrain mount. zCARRY OUT Klj . 23 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Generator electrical
field or bearings. z
CARRY OUT generator
load test. REPAIR or
INSTALL a new generator
as necessary. REFER to
Section 414 - 02 .
z Drone type noise zExhaust system. zCARRY OUT the Exhaust System Neutralizing in this
section. REPAIR as
necessary.
z A/C compressor. zCHECK for noise with
vehicle at constant speeds.
CYCLE the compressor on
and off and listen for a
change in pitch. REPAIR as
necessary. REFER to
Section 412 - 03 .
z Powertrain mounts. zCARRY OUT the
Powertrain/Drivetrain Mount Neutralizing in this
section.
z Sputter type
noise— noise
worse when cold,
lessens or
disappears when
vehicle is at
operating
temperature z
Damaged or worn
exhaust system
components. z
INSPECT the exhaust
system for leaks or
damage. REPAIR as
necessary. REFER to
Section 309 - 00 .
z Rattling noise—
noise from the
upper engine
(valve train).
Worse when
engine is cold z
Low oil level. zCHECK oil level. FILL as
necessary.
z Thin or diluted oil. zINSPECT the oil for
contamination. If oil is
contaminated, CHECK for
the source. REPAIR as
necessary. CHANGE the oil
and filter.
z Low oil pressure. zCARRY OUT an oil
pressure test. If not within
specifications, REPAIR as
necessary. REFER to
Section 303 - 00 .
z Worn rocker
arms/fulcrums or
followers. z
CARRY OUT a valve train
analysis. INSTALL new
valve train components as
necessary. REFER to
Section 303 - 01A for 3.8L
engines or Section 303 - 01B
for 4.6L (2V) engines.
z Worn valve guides. zCARRY OUT a valve train
analysis. INSTALL new
valve guides as necessary.
REFER to Section 303 - 01A
for 3.8L engines or
Section 303 - 01B for 4.6L (2V)
engines. Klj . 26 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

as necessary.
z Accelerator pedal
vibration— felt
through the pedal
as a buzz z
Throttle cable loose
or misrouted. z
INSPECT the throttle cable.
REPAIR as necessary.
REFER to Section 310 - 02 .
z Engine
vibration— mostly
at coast/neutral
coast. Condition
improves with
vehicle
accelerating z
Combustion
instability. z
CHECK the ignition system.
INSTALL new components
as necessary.
z Engine vibration
or shudder—
occurs with light
to medium
acceleration
above 56 km/h
(35 mph) z
Worn or damaged
spark plugs. z
INSPECT the spark plugs
for cracks, high resistance
or broken insulator.
INSTALL a new spark plug
(s) as necessary.
z Plugged fuel injector. zREPAIR or INSTALL a new
injector as necessary.
REFER to Section 303 - 04A
for 3.8L engines or
Section 303 - 04B for 4.6L (2V)
engines.
z Damaged spark plug
wire. z
INSPECT the spark plug
wires for damage. INSTALL
a new spark plug wire(s) as
necessary.
z Contaminated fuel. zINSPECT the fuel for
contamination. DRAIN the
fuel system and refill.
z Worn or damaged
torque converter. z
CHECK the torque
converter. INSTALL a new
torque converter as
necessary. REFER to
Section 307 - 01 .
Symptom Chart—
Idle Noise/Vibration Condition
Possible Sources Action
z Idle air control (IAC)
valve moan — occurs
on throttle tip- out z
IAC valve is
contaminated
with oil. z
GO to Component Tests in
this section.
z Accessory drive belt
chirp — occurs at idle
or high idle, cold or
hot. Most common
occurrence is during
humid weather z
Accessory drive
belt worn, or
pulley is
misaligned or
loose. z
INSPECT for loose or
misaligned pulleys. CHECK
the drive belt for wear or
damage. INSTALL new
pulley(s)/drive belt, or
accessory drive components
as necessary. REFER to
Section 303 - 05 .
z Accessory drive
bearing hoot —
occurs at idle or high
idle in cold
temperatures of
approximately +4°C z
Accessory drive
idler or
tensioner pulley
bearing is
experiencing
stick/slip z
Go To Pinpoint Test C . Klj . 28 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Section 308 - 02 .
z Grease or oil on the
clutch disc facing. z
CHECK the input shaft
seal and rear main oil
seal. REPAIR as
necessary. INSTALL a
new clutch disc.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Clutch disc surface
glazed or damaged. z
INSPECT the clutch
disc surface for a
glazed, hardened or
damage condition.
CARRY OUT a disc
check. INSTALL a new
clutch disc as
necessary. REFER to
Section 308 - 01 .
z Damaged or worn
clutch pressure
plate. z
INSPECT the clutch
pressure plate for wear
or damage. INSTALL a
new clutch pressure
plate as necessary.
REFER to Section 308 -
01 .
z Flywheel surface
damaged or glazed. z
INSPECT the flywheel
for damage or wear.
CARRY OUT a
flywheel runout check.
INSTALL a new
flywheel as necessary.
REFER to Section 303 -
01A for 3.8L engines or
Section 303 - 01B for
4.6L (2V) engines.
z Clutch chatter noise—
noise when clutch
pedal is released at
initial take- off. Clutch is
hard to engage and
disengage z
Pilot bearing worn,
damaged or not
correctly aligned in
bore. z
INSPECT the clutch
pressure plate release
fingers for uneven
wear, clutch
components burnt or a
seized pilot bearing.
INSTALL a new pilot
bearing as necessary.
REFER to Section 308 -
01 .
z Clutch vibration zLoose flywheel
bolts.
z Damaged or loose
clutch pressure
plate.
z Excessive flywheel
runout. z
Go To Pinpoint Test L .
z Transmission
rattling/clattering
noise— noise at idle or
on light acceleration
from a stop. Gear
selection difficult z
Gearshift lever joint
worn or damaged. z
INSTALL a new
gearshift lever. REFER
to Section 308 - 03A for
T50D transmissions or
Section 308 - 03B for
TR3650 transmissions. Klj . 41 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Is the ticking noise gone? CHECK for TSB for applicable vehicle.
REPAIR as necessary. TEST the system
for normal operation.
No
GO to
B2 .
B2 CHECK FOR TICKING NOISE AT THE FUEL
INJECTOR z
Using an EngineEAR, listen at the fuel
injectors by placing a probe on each injector.
To isolate the faulty injector, disconnect the
injector electrical connector and listen for the
noise.
z Is the fuel injector the source of the ticking
noise? Yes
INSTALL a new fuel injector. REFER to
Section 303
- 04A for 3.8L engines or
Section 303 - 04B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B3 .
B3 CHECK THE BELT TENSIONER FOR TICKING
NOISE z
Inspect the accessory drive. Check for the belt
tensioner bottoming at end of travel or not at
end of stroke.
z Using an EngineEAR, listen at the belt
tensioner.
z Is the belt tensioner the source of the
noise? Yes
INSTALL a new belt tensioner. TEST the
system for normal operation.
No
GO to
B4 .
B4 CHECK THE WATER PUMP FOR TICKING
NOISE z
Using an EngineEAR, listen at the water pump
for ticking noise.
z Is the water pump the source of the noise? Yes
INSTALL a new water pump. REFER to
Section 303
- 03A . TEST the system for
normal operation.
No
GO to B5 .
B5 CHECK FOR AN OBSTRUCTION OF THE
COOLING FAN z
Inspect the cooling fan for obstructions.
z Check the cooling fan and shroud for wear or
damage.
z Was there an obstruction or does the
cooling fan show signs of damage? Yes
REPAIR or INSTALL a new cooling fan.
REFER to
Section 303 - 03A . TEST the
system for normal operation.
No
GO to B6 .
B6 CHECK THE OIL PUMP FOR TICKING NOISE
z
Check the oil pump using EngineEARs and
probe at the oil filter adapter to verify the oil
pump as a source.
z Is the oil pump the source of the noise? Yes
INSTALL a new oil pump. REFER to
Section 303
- 01A for 3.8L engines or
Section 303 - 01B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B7 .
B7 CHECK VALVE LIFTERS OR LASH
ADJUSTERS FOR CORRECT OPERATION z
Check valve lifter/lash adjuster for correct
operation, using EngineEARs.
z Are the valve lifters/lash adjusters Yes
VERIFY customer concern. CONDUCT a
diagnosis of other suspect components. Klj . 50 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Repair the axle as necessary. Make sure the axle lubricant is at the correct level. Refer to
Specifications in this section.
Axle Vent
NOTE:
If a plugged vent cannot be cleared, install a new one.
A plugged vent will cause excessive seal lip wear due to internal pressure buildup. If a leak occurs,
check the vent. Make sure the vent hose is not kinked. Remove the hose from the vent nipple and
clear the hose of any foreign material. While the hose is removed, pass a length of mechanics wire in
and out of the vent to clean it. Connect the hose when done.
Flange Yoke Seal
Leaks at the axle drive pinion seal originate for the following reasons:
zSeal was not correctly installed.
z Poor quality seal journal surface.
Any damage to the seal bore (dings, dents, gouges, or other imperfections) will distort the seal casing
and allow leakage past the outer edge of the axle drive pinion seal.
The axle drive pinion seal can be torn, cut, or gouged if it is not installed carefully. The spring that
holds the axle drive pinion seal against the pinion flange may be knocked out and allow leakage past
the lip.
The rubber lips can occasionally become hard (like plastic) with cracks at the oil lip contact point. The
contact point on the pinion flange may blacken, indicating excessive heat. Marks, nicks, gouges, or
rough surface texture on the seal journal of the pinion flange will also cause leaks.
When a seal leak occurs, install a new seal and check the vent and the vent hose to make sure they
are clean and free of foreign material.
Axle Shaft Seals
Axle shaft oil seals are susceptible to the same kinds of damage as axle drive pinion seals if incorrectly
installed. The seal bore must be clean and the lip handled carefully to avoid cutting or tearing it. The
axle shaft journal surface must be free of nicks, gouges, and rough surface texture.
Differential Seals
Refer to Section 205 - 02A or
Section 205 - 02B .
Analysis of Vibration WARNING: A vehicle equipped with a Traction- Lok® differential will always have both
wheels driving. If only one wheel is raised off the floor and the rear axle is driven by the engine,
the wheel on the floor could drive the vehicle off the stand or jack. Be sure both rear wheels are
off the floor.
Few vibration conditions are caused by the rear axle. On a vibration concern, follow the diagnosis
procedure in Section 100 - 04 unless there is a good reason to suspect the axle.
Tires Klj . 3 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST F: HYDRO-
BOOST ERRATIC OPERATION, STICKS,
BINDS OR GRABS z
Check accessory drive belt tension and
condition. Refer to Section 303 - 05 .
z Is the accessory drive belt OK? Yes
GO to
E3 .
No
INSTALL a new accessory drive belt.
REFER to Section 303 - 05 .
E3 CHECK POWER STEERING HOSES
z
Check power steering pressure hoses, power
steering gear pressure hoses and power
steering return hose for cracks or leaks.
z Do power steering pressure hose, power
steering gear hose and power steering
return hose check OK? Yes
GO to
E4 .
No
INSTALL new hoses as necessary.
REFER to Section 211 - 00 .
E4 CHECK BRAKE PEDAL LINKAGE
z
Check brake pedal linkage for binding or
sticking operation.
z Does pedal linkage check OK? Yes
GO to
E5 .
No
INSTALL new pedal linkage as necessary.
REFER to Section 206 - 06 .
E5 CHECK POWER STEERING PUMP SPEED
z
Check engine idle speed against
specifications.
z Is engine idle speed OK? Yes
GO to
E6 .
No
SET engine idle speed to specification.
REFER to Powertrain Control/Emissions
Diagnosis (PC/ED) manual. E6 CHECK FOR PLUGGED RETURN HOSE
z
NOTE: The return hose from the oil cooler to
the power steering reservoir has an in- line
filter in the hose.
z Disconnect power steering return hose from
power steering fluid cooler and power
steering pump reservoir.
z Pass air through hose from the oil cooler end.
z Is hose plugged? Yes
INSTALL a new power steering return
hose.
No
GO to
E7 .
E7 CHECK POWER STEERING PUMP FLOW
AND RELIEF z
Test power steering pump for correct flow
and relief pressure. Refer to Section 211 - 00 .
z Is power steering pump operating
correctly? Yes
INSTALL a new power brake hydro-
boost
unit. REFER to Section 206 - 07 .
No
INSTALL a new power steering pump.
REFER to Section 211 - 02 .
Test Step Result / Action to
Take F1 CHECK SUPPLY HOSE
z
Check for obstructions in power steering return hose and Yes Klj . 11 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...