2003 FORD MUSTANG oil change

z
If equipped, inspect automatic transmission fluid level with dipstick.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new cabin air filter.
z If filled with green engine coolant, change coolant.
224,000 Km (140,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
232,000 Km (145,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
240,000 Km (150,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect exhaust system and heat shields.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new engine air filter.
z Install a new fuel filter. (See ADDITIONAL INFORMATION below.)
z If equipped, install a new cabin air filter.
z If filled with yellow engine coolant, change coolant or at 8 years, whichever comes first.
z Change automatic transmission/transaxle fluid and filter.
z Change rear axle lubricant on all rear wheel (RWD) vehicles.
z Install a new accessory drive belt(s) (if a new belt has not been installed within the last 100,000
miles).
z If equipped, install new climate controlled seat filters (Navigator, Lincoln LS and Aviator).
ADDITIONAL INFORMATION: If vehicle is registered in California, the California Air Resources Board
(CARB) has determined that failure to install a new fuel filter at this interval will not nullify the emission
warranty or limit recall liability prior to completion of the vehicle's useful life. It is, however
recommended that maintenance checks be carried out and recorded at the indicated intervals.
Additional checks for natural gas and propane vehicles include inspecting fuel tanks, as well as
draining and installing a new filter. Klj . 9 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Generator electrical
field or bearings. z
CARRY OUT generator
load test. REPAIR or
INSTALL a new generator
as necessary. REFER to
Section 414 - 02 .
z Drone type noise zExhaust system. zCARRY OUT the Exhaust System Neutralizing in this
section. REPAIR as
necessary.
z A/C compressor. zCHECK for noise with
vehicle at constant speeds.
CYCLE the compressor on
and off and listen for a
change in pitch. REPAIR as
necessary. REFER to
Section 412 - 03 .
z Powertrain mounts. zCARRY OUT the
Powertrain/Drivetrain Mount Neutralizing in this
section.
z Sputter type
noise— noise
worse when cold,
lessens or
disappears when
vehicle is at
operating
temperature z
Damaged or worn
exhaust system
components. z
INSPECT the exhaust
system for leaks or
damage. REPAIR as
necessary. REFER to
Section 309 - 00 .
z Rattling noise—
noise from the
upper engine
(valve train).
Worse when
engine is cold z
Low oil level. zCHECK oil level. FILL as
necessary.
z Thin or diluted oil. zINSPECT the oil for
contamination. If oil is
contaminated, CHECK for
the source. REPAIR as
necessary. CHANGE the oil
and filter.
z Low oil pressure. zCARRY OUT an oil
pressure test. If not within
specifications, REPAIR as
necessary. REFER to
Section 303 - 00 .
z Worn rocker
arms/fulcrums or
followers. z
CARRY OUT a valve train
analysis. INSTALL new
valve train components as
necessary. REFER to
Section 303 - 01A for 3.8L
engines or Section 303 - 01B
for 4.6L (2V) engines.
z Worn valve guides. zCARRY OUT a valve train
analysis. INSTALL new
valve guides as necessary.
REFER to Section 303 - 01A
for 3.8L engines or
Section 303 - 01B for 4.6L (2V)
engines. Klj . 26 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Suspension System
Inspection and Verification
1. Road test. zVerify the customer's concern by performing a road test on a smooth road.
2. Inspect tires. zCheck the tire pressure with all normal loads in the vehicle and the tires cold. For
additional information, refer to the vehicle certification (VC) label.
z Verify that all tires are sized to specification.
z Inspect the tires for incorrect wear and damage.
3. Inspect chassis and underbody. zRemove any excessive accumulation of mud, dirt or road deposits from the chassis and
underbody.
4. Inspect for aftermarket equipment. zCheck for aftermarket changes to the steering, suspension, wheel and tire components
(such as competition, heavy duty, etc.) The specifications shown in this manual do not
apply to vehicles equipped with aftermarket equipment.
5. Inspect shock absorbers. All vehicles are equipped with gas- pressurized hydraulic shock absorbers. These shock
absorbers are not adjustable or refillable and cannot be repaired.
zOil Leak: A light film of oil (weepage) on the upper portion of the shock absorber is
permissible and is a result or correct shock lubrication. Weepage is a condition in which a
film of oil accumulates on the thin tube (body) and is normally noticed due to the
collection of dust in this area. If shock absorbers exhibit this weepage condition, they are
functional units and new shock absorbers should not be installed. Leakage is a condition
in which the entire shock absorber body is covered with oil and the oil will drip from the
shock absorber onto the pavement. If condition exists:
„Make sure fluid observed is not from sources other than the shock absorber.
„ Install a new shock absorber, if necessary.
z Vehicle Sag: Many times new shock absorbers are installed in an effort to solve a vehicle
sag concern. Shock absorbers by design are hydraulic damping units only and, unlike
suspension springs, do not support any suspension loads. Therefore, installing a new
shock absorber will not correct a vehicle sag concern.
z Installment in Pairs: In the past it was recommended that new shock absorbers be
installed in pairs if one unit became unrepairable. New shock absorbers no longer need
to be installed in pairs when only one unit is not repairable.
SECTION 204-
00: Suspension System — General Information 2003 Mustang Workshop Manual Visual Inspection Chart
Mechanical Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Engines need oil to lubricate the following internal components:
zcylinder block cylinder walls
z pistons and piston, pin and rings (6102)
z intake and exhaust valve stems
z intake and exhaust valve guides
z all internal engine components
When the pistons move downward, a thin film of oil is left on the cylinder walls. As the vehicle is
operated, some oil is also drawn into the combustion chambers past the intake and exhaust valve
stem seals and burned.
The following is a partial list of conditions that can affect oil consumption rates:
zengine duty cycle
z operator driving habits
z ambient temperature
z quality and viscosity of the oil
Operation under varying conditions can frequently be misleading. A vehicle that has been run for
several thousand miles on short trips or in below- freezing ambient temperatures may have consumed
a "normal" amount of oil. However, when checking the engine oil level, it may measure up to the FULL
or MAX on the oil level dipstick due to dilution (condensation and fuel) in the engine crankcase. The
vehicle might then be driven at high speeds on the highway where the condensation and fuel boil off.
The next time the engine oil is checked, it may appear that a liter (quart) of oil was used in about 160
km (100 miles). This perceived 160 km (100 miles) per liter (quart) oil consumption rate causes
customer concern even though the actual overall oil consumption rate is about 2,400 km (1,500 miles)
per liter (quart).
Make sure the selected engine oil meets the current recommended API performance category with
SAE viscosity grade as shown in the vehicle Owner's Guide. It is also important that the engine oil is
changed at the intervals specified. Refer to the vehicle Owner's Guide.
Oil Pressure Test
1. Disconnect and remove the oil pressure sensor (9278) from the engine.
2. Connect the Oil Pressure Gauge to the oil pressure sender oil galley port.
3. Run the engine until normal operating temperature is reached.
4. Run the engine at the specified rpm and record the gauge reading.
5. The oil pressure should be within specifications; refer to the specification chart in the appropriate engine section.
6. If the pressure is not within specification, check the following possible sources: zinsufficient oil
z oil leakage
z worn or damaged oil pump
z oil pump screen cover and tube (6622)
z excessive main bearing clearance Klj . 13 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Connecting Rod —
Cleaning
CAUTION: Do not use a caustic cleaning solution or damage to connecting rods can
occur.
1. NOTE: The connecting rod large end is a matched set. The connecting rod cap must be
installed on the original connecting rod in the original position. Do not reverse the cap. Parts are
not interchangeable.
Mark and separate the parts and clean with solvent. Clean the oil passages.
SECTION 303-
00: Engine System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
SECTION 303-
01A: Engine — 3.8L 2003 Mustang Workshop Manual General Specifications
Item Specification
Lubricants and Sealants
SAE 5W-
20 Premium Synthetic Blend Motor Oil
XO- 5W20- QSP WSS-
M2C153- H Gasket and Trim Adhesive F3AZ-19B508-
AA ESE-
M2G52- A Pipe Sealant with Teflon® D8AZ-19554-
A WSK-
M2G350- A2 Silicone Gasket and Sealant F7AZ-19554-
EA WSE-
M4G323- A4 Metal Surface Cleaner F4AZ-19A536-
RA WSE-
M5B392- A Engine
Displacement 3.8L
Number of cylinders 6
Bore 96.8325 mm (3.81 in)
Stroke 86.0 mm (3.39 in)
Firing order 1-4-2-5-3-
6 Oil pressure (hot 2,500 rpm) 40-
125 psi Oil capacity 5 quarts w/filter change
Compression ratio —
Cylinder Head and Valve Train
Cylinder head gasket surface flatness 0.18 mm (0.007 in)
Combustion chamber volume 61.5-
64.5 cc Valve arrangement (front to rear) —
Valve guide bore diameter 7.015-
7.044 mm (0.276- 0.277 in) Valve stem diameter —
intake 6.955-
6.988 mm (0.2738- 0.2751 in) Valve stem diameter —
exhaust 6.929-
6.962 mm (0.2728- 0.2741 in) Valve stem diameter —
oversize (intake) 9.075-
9.055 mm (0.3573- 0.3565 in) Valve stem diameter —
oversize (exhaust) 9.063-
9.043 mm (0.3568- 0.3560 in) Valve stem diameter —
oversize (intake) 9.456-
9.436 mm (0.3723- 0.3715 in) Valve stem diameter —
oversize (exhaust) 9.444-
9.424 mm (0.3718- 0.3710 in) Valve stem-
to-guide clearance — intake 0.020-
0.069 mm (0.045- 0.090 in) Valve stem-
to-guide clearance — exhaust 0.038-
0.083 mm (0.0015- 0.0033 in) Valve head diameter —
intake 47.27 mm (1.86 in)
Valve head diameter —
exhaust 37.1 mm (1.46 in)
Valve face runout 0.05 mm (0.002 in)
Valve face angle 45.675 degrees
Valve seat width 1.5-
2.0 mm (0.06- 0.08 in) Valve seat runout (T.I.R.) 0.076 mm (0.003 in) Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Engine Cooling
Inspection and Verification
WARNING: Never remove the pressure relief cap while the engine is operating or when the
cooling system is hot. Failure to follow these instructions can result in damage to the cooling
system or engine or personal injury. To avoid having scalding hot coolant or steam blow out of
the degas bottle when removing the pressure relief cap, wait until the engine is cooled, then
wrap a thick cloth around the pressure relief cap and turn it slowly. Step back while the
pressure is released from the cooling system. When you are sure all the pressure has been
released, turn and remove the pressure relief cap (still with a cloth).
CAUTION: Check the coolant level, engine oil and transmission fluid, top off the coolant if
needed. If there is engine coolant in the engine oil or transmission fluid, the cause must be
corrected and oil/fluid changed or major component damage may occur.
1. Verify the customer's concern by operating the engine to duplicate the condition.
2. Inspect to determine if any of the following mechanical or electrical concerns apply.
SECTION 303-
03A: Engine Cooling 2003 Mustang Workshop Manual Special Tool(s)
Pressure Tester
014-
R1072 or equivalent 73III Automotive Meter
105-
R0057 or equivalent Worldwide Diagnostic System
(WDS)
418-
F224,
New Generation STAR (NGS)
Tester
418- F052, or equivalent scan
tool Battery/Anti-Freeze Tester
014- R1060 or equivalent Klj . 1 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

3.
NOTE: Running this test with the vehicle in gear or with the A/C compressor clutch engaged
(running) will cause incorrect diagnosis.
Place the transmission in PARK (P) or NEUTRAL (N).
4. Start the engine and allow the engine to idle throughout this test. Allow the engine to run for 2 minutes, then record the ECT (4.6L) or CHT (3.8L) voltage. Record the ECT (4.6L) or CHT
(3.8L) voltage every 60 seconds. When the ECT (4.6L) or CHT (3.8L) voltage trend changes
direction or only changes slightly (0.03 volts or less) from the previous reading, record this as
the thermostat opening voltage. Use the voltage and corresponding coolant temperature chart
listed below for 4.6L engines only.
5. If the thermostat opening voltage is greater than 0.75 volts and less than 82°C (180°F), install a new water thermostat.
6. If the thermostat opening voltage is less than 0.75 volts and greater than 82°C (180°F), the water thermostat is good and a new water thermostat should not be installed. GO to Symptom Chart for further instructions.
Thermostat — Mechanical Test
1. Remove the water thermostat.
2. Check the water thermostat for seating. Hold the water thermostat up to a lighted background. Leakage of light around the thermostat valve at room temperature indicates that a new water
thermostat should be installed. Some water thermostats have a small leakage notch at one
location on the perimeter of the thermostat valve, which is considered normal.
3. Immerse the water thermostat in a boiling coolant and water mixture.
4. See the General Specifications chart for water thermostat opening temperatures.
Radiator Leak Test, Removed From the Vehicle CAUTION: Never leak test an aluminum radiator in the same water that copper/brass
radiators are tested in. Flux and caustic cleaners may be present in the cleaning tank and they
will damage aluminum radiators.
NOTE: Always install plugs in the oil cooler fittings before leak- testing or cleaning any radiator.
NOTE: Clean the radiator before leak- testing to avoid contamination of tank. Coolant Temperature °C (°F) ECT (Volts)
22 (71) 3.00
43 (109) 2.01
71 (159) 1.01
82 (180) 0.75
91 (195) 0.059
97 (206) 0.050
105 (221) 0.040 Klj . 9 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...