2003 FORD MUSTANG brakes

closing/opening
the window
z Squeak— heard
outside of vehicle
when
closing/opening
the door z
Exhaust shield
rubbing against
the chassis or
exhaust pipe. z
CHECK the exhaust system.
REPAIR as necessary. REFER
to Section 309 - 00 .
z Squeak— occurs
with initial brake
pedal application z
Disc brake pads. zUnder certain conditions,
asbestos free pads can
generate a squeak noise. This
noise is normal and does not
indicate a concern.
z Squeak— a
constant noise
that occurs with
brake pedal
applications z
Damaged or
worn disc brake
pads. z
INSPECT the pads for oil,
grease or brake fluid
contamination. CHECK for
glazed linings. A brake disc with
hard spots will also cause a
squeak type noise. REPAIR or
INSTALL new pads as
necessary. REFER to Section 206 - 03 for front disc brakes and
Section 206 - 04 for rear disc
brakes.
z Squeak— noise
occurs over
bumps or when
turning z
Worn control
arm bushings. z
INSPECT the control arm
bushings. Spray with lubricant
and CARRY OUT a "bounce
test" to determine which
bushing. REPAIR as necessary.
REFER to Section 204 - 01 .
z Worn or
damaged shock
absorber/strut. z
INSPECT the shock absorber
for damage. CARRY OUT a
"bounce test" to isolate the
noise. INSTALL a new shock
absorber/strut as necessary.
REFER to Section 204 - 01 for
the front shock absorber/strut or
Section 204 - 02 for the rear
shock absorber/strut.
z Rattle— heard
when
closing/opening
the door or
window z
Loose internal
door
mechanism,
bracket or
attachment. z
REPEAT the motion or CARRY
OUT a "tap test" to duplicate the
noise. INSPECT the door for
loose components. TIGHTEN
loose components or USE the
Rotunda Squeak and Rattle Kit
to isolate any rattling
components.
z Rattle — GT
models only,
noise occurs from
the rear of the
vehicle z
A loose or under
torqued shock
damper
attaching nut. z
VERIFY the torque on the
shock damper- to-axle nuts is 63
Nm (46 lb- ft). VERIFY the
torque for the shock damper- to-
rail bracket nuts is 90 Nm (66
lb- ft). Do not over torque.
TIGHTEN as necessary.
z Squeak or rattle—
heard inside the
vehicle over rough
roads/bumps z
Misaligned glove
compartment
door/hinge. z
ALIGN the glove compartment
door.
z Instrument panel
trim loose or z
INSPECT the instrument panel
trim for missing or loose clips or Klj . 32 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

condition. It may not always be necessary to follow a pinpoint test to its conclusion. Carry out only the
steps necessary to correct the condition. Then, test the system for normal operation. Sometimes, it is
necessary to remove various vehicle components to gain access to the component requiring testing.
Reinstall all components after verifying system operation is normal.
PINPOINT TEST A: BRAKE VIBRATION/SHUDDER
Test Step Result / Action to Take
A1 ROAD TEST THE VEHICLE—
LIGHT BRAKING z
Check that the wheel and tires are correct for the vehicle.
Inspect the tires for abnormal wear patterns.
z Road test the vehicle. Warm the brakes by slowing the vehicle
a few times from 80– 32 km/h (50 to 20 mph) using light braking
applications. At highway speeds of 89–97 km/h (55- 60 mph),
apply the brake using a light pedal force.
z Is there a vibration/shudder felt in the steering wheel, seat
or brake pedal? Yes
GO to
A4 .
No
GO to A2 .
A2 ROAD TEST THE VEHICLE—
MODERATE TO HEAVY
BRAKING z
Road test the vehicle. At highway speeds of 89–97 km/h (55- 60
mph), apply the brake using a moderate to heavy pedal force.
z Is there a vibration/shudder? Yes
For vehicles with ABS,
GO to
A3 . For vehicles
with standard brakes,
GO to A4 .
No
Vehicle is OK. VERIFY
condition with customer.
TEST the vehicle for
normal operation. A3 NORMAL ACTUATION OF THE ABS SYSTEM DIAGNOSIS
z
During moderate to heavy braking, noise from the hydraulic
control unit (HCU) and pulsation in the brake pedal can be
observed. Pedal pulsation coupled with noise during heavy
braking or on loose gravel, bumps, wet or snowy surfaces is
acceptable and indicates correct functioning of the ABS
system. Pedal pulsation or steering wheel nibble, (frequency is
proportioned to the vehicle speed) indicates a concern with a
brake or suspension component.
z Is the vibration/shudder vehicle speed sensitive? Yes
GO to
A5 .
No
The brake system is
operating correctly. A4 APPLICATION OF THE PARKING BRAKE
z
NOTE: Begin at the front of the vehicle unless the vibration or
shudder has been isolated to the rear.
z This test is not applicable to vehicles with drum- in-hat type
parking brakes. For vehicles with drum- in-hat parking brakes,
proceed to the next test. For all other vehicles, apply the
parking brake to identify if the problem is in the front or rear
brake. At highway speeds of 89–97 km/h (55- 60 mph), lightly
apply the parking brake until the vehicle slows down. Release
the parking brake immediately after the test.
z Is there a vibration/shudder? Yes
GO to
A7 .
No
GO to A5 .
A5 CHECK THE FRONT WHEEL BEARINGS
z
Check the front wheel bearings. Refer to Wheel Bearing Check in this section.
z Are the wheel bearings OK? Yes
GO to
A6 . Klj . 48 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

13. Connect the parking brake cable and conduit to the rear brake caliper and install the clip.
14. Connect the parking brake cable and conduit to the parking brake lever.
15.
CAUTION: The axle retainer must be tightened with the brakes applied and the
wheels off the ground to make sure of correct bearing seating. Failure to do so can
cause the retainer to loosen, causing extensive vehicle damage and loss of vehicle
control.
Lower the vehicle and apply the parking brake or service brakes.
16. Tighten the retainer.
17. Install the wheel and tire assembly. For additional information, refer to Section 204 - 04
18. Lower the vehicle.
19. Check the wheel alignment. Adjust as necessary. For additional information, refer to
Section 204 - 00 . Klj . 8 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Component Tests
Driveline Vibration
An analysis of driveline vibration can also be conducted using the Vibration Analyzer; follow the
manufacturer's directions.
Driveline vibration exhibits a higher frequency and lower amplitude than does high-
speed shake.
Driveline vibration is directly related to the speed of the vehicle and is usually noticed at various speed
ranges. Driveline vibration can be perceived as a tremor in the floorpan or is heard as a rumble, hum,
or boom. Driveline vibration can exist in all drive modes, but may exhibit different symptoms depending
upon whether the vehicle is accelerating, decelerating, floating, or coasting. Check the driveline angles
if the vibration is particularly noticeable during acceleration or deceleration, especially at lower speeds.
Driveline vibration can be duplicated by supporting the axle upon a hoist or upon jack stands, though
the brakes may need to be applied lightly in order to simulate road resistance.
1. Raise the vehicle promptly after road testing. Use a twin- post hoist or jack stands to prevent tire
flat- spotting. Engage the drivetrain and accelerate to the observed road test speed to verify the lubricant type.
205 - 02B . CLEAN and
REFILL the axle to
specification.
z Axle overheating zLubricant level too
low. z
CHECK the lubricant level.
FILL the axle to specification.
z Incorrect or
contaminated
lubricant type. z
INSPECT the axle for
damage. REPAIR as
necessary. CLEAN and
REFILL the axle to
specification.
z Bearing preload
adjusted too tight. z
CHECK the ring and pinion for
damage. INSPECT the ring
and pinion wear pattern.
ADJUST the preload as
necessary.
z Excessive gear
wear. z
INSPECT all the axle gears
for wear or damage. INSTALL
new components as
necessary.
z Incorrect ring gear
backlash. z
INSPECT the ring gear for
scoring. INSPECT the ring
and pinion wear pattern.
ADJUST the ring gear
backlash as necessary.
z Broken gear teeth
on the ring gear
or pinion z
Overloading the
vehicle. z
INSTALL a new ring and
pinion. REFER to Section 205 - 02A or
Section 205 - 02B .
z Axle shaft broken zOverloading the
vehicle. z
INSTALL a new axle shaft.
REFER to Section 205 - 02A or
Section 205 - 02B .
z Misaligned axle
shaft tube. z
INSPECT the axle for
damage. CHECK axle shaft
tube alignment. INSTALL a
new axle shaft. REFER to
Section 205 - 02A or
Section 205 - 02B . Klj . 11 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1. Position the two U-
washers on the button end of the axle shaft.
2. Pull the axle shaft outward.
4. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and
Sealer EOAZ- 19554-AA or equivalent meeting Ford specification WSK-M2G351- A5 prior to
installation.
Install the differential pinion shaft. 1. Align the hole in the differential pinion shaft with the case lock bolt hole.
2. Install a new differential pinion shaft lock bolt.
5. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
6. Install the rear brake anti- lock sensor. For additional information, refer to Section 206 - 09A .
7. Install the rear brakes. For additional information, refer to Section 206 - 04 .
8. Install the tire and wheel assembly. For additional information, refer to Section 204 - 04 .
9. Lower the vehicle. Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1. Position the two U-
washers on the button end of the axle shaft.
2. Pull the axle shaft outward.
4. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and
Sealer EOAZ- 19554-AA or equivalent meeting Ford specification WSK-M2G351- A5 prior to
installation.
Install the differential pinion shaft. 1. Align the hole in the differential pinion shaft with the case lock bolt hole.
2. Install a new differential pinion shaft lock bolt.
5. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
6. Install the rear brake anti- lock sensor. For additional information, refer to Section 206 - 09A .
7. Install the rear brakes. For additional information, refer to Section 206 - 04 .
8. Install the tire and wheel assembly. For additional information, refer to Section 204 - 04 .
9. Lower the vehicle. Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

The vehicle is equipped with a vacuum-
assisted or a hydro-boost power braking system. Refer to
Section 206 - 07 .
The braking system is a front- to-rear split hydraulic system. Refer to Section 206 - 06 .
The front wheel brakes utilize a dual piston brake caliper and disc brake system. Refer to Section 206 -
03 .
The rear brakes utilize a single piston brake caliper and disc brake system. Refer to Section 206 - 04 .
The parking brake system is a mechanical system that is controlled by an independent hand- operated
parking brake control and is self- adjusting. Refer to Section 206 - 05 .
A 4- wheel anti- lock brake system or anti-lock brake system with traction control (4WABS) is optional
equipment on all models except Cobra. Cobra has ABS and traction control as standard equipment.
Refer to Section 206 - 09A . hydraulic control unit and control module assy (non-
traction)
1 2C353 Four wheel anti-
lock brake system (4WABS)
hydraulic control unit and control module assy
(traction) 2 2B559 Hydro-Boost brake booster and brake master
cylinder assy 3 2B195 Vacuum brake booster and brake master cylinder
assy
4 2K327 Rear disc brake assy
5 2780 Parking brake control
6 2B119 Front disc brake assy Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Brake System
Refer to Wiring Diagrams Cell
60 , Instrument Cluster for schematic and connector information.
Refer to Wiring Diagrams Cell 97 , Daytime Running Lamps for schematic and connector information.
Inspection and Verification WARNING: Use of any other than the approved DOT 3 brake fluid will cause permanent
damage to brake components and will render the brakes inoperative.
WARNING: Brake fluid contains polyglycol ethers and polyglycols. Avoid contact with
eyes. Wash hands thoroughly after handling. If brake fluid contacts eyes, flush eyes with
running water for 15 minutes. Get medical attention if irritation persists. If taken internally,
drink water and induce vomiting. Get medical attention immediately.
CAUTION: Do not spill brake fluid onto painted surfaces. If spilled, wipe up immediately.
NOTE: Always check the fluid level in the brake master cylinder reservoir (2K478) before performing
the test procedures. If the fluid level is not at the correct level, add High Performance DOT 3 Brake
Fluid C6AZ- 19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA- M6C25-A.
NOTE: Prior to performing any diagnosis, make sure the brake warning indicator is functional. For
additional information, refer to Section 413 - 01 .
The first indication that something may be wrong in the brake system is a change in the feeling through
the brake pedal (2455). The brake warning indicator in the instrument cluster and the brake fluid level SECTION 206-
00: Brake System — General Information 2003 Mustang Workshop Manual Special Tool(s)
73 Digital Multimeter
105-
R0051 or Equivalent ABS Brake and Pressure Test
Kit
107-
02350 or Equivalent Tire and Wheel Runout Gauge
Set
134-
00199 or Equivalent Klj . 1 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...