2003 FORD MUSTANG test G

Intake Manifold Vacuum Test
Bring the engine to normal operating temperature. Connect the Vacuum/Pressure Tester to the intake
manifold. Run the engine at the specified idle speed.
The vacuum gauge should read between 51-
74 kPa (15-22 in-Hg) depending upon the engine
condition and the altitude at which the test is performed. Subtract 4.0193 kPa (1 in- Hg) from the
specified reading for every 304.8 m (1,000 feet) of elevation above sea level.
The reading should be steady. If necessary, adjust the gauge damper control (where used) if the
needle is fluttering rapidly. Adjust the damper until the needle moves easily without excessive flutter.
Intake Manifold Vacuum Test—Interpreting Vacuum Gauge Readings
A careful study of the vacuum gauge reading while the engine is idling will help pinpoint trouble areas.
Always conduct other appropriate tests before arriving at a final diagnostic decision. Vacuum gauge
readings, although helpful, must be interpreted carefully.
Most vacuum gauges have a normal band indicated on the gauge face.
The following are potential gauge readings. Some are normal; others should be investigated further.
1. NORMAL READING: Needle between 51- 74 kPa (15-22 in-Hg) and holding steady.
2. NORMAL READING DURING RAPID ACCELERATION AND DECELERATION: When the engine is rapidly accelerated (dotted needle), the needle will drop to a low reading (not to zero).
When the throttle is suddenly released, the needle will snap back up to a higher than normal
figure.
3. NORMAL FOR HIGH- LIFT CAMSHAFT WITH LARGE OVERLAP: The needle will register as low as 51 kPa (15 in - Hg) but will be relatively steady. Some oscillation is normal. Klj . 11 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Engines need oil to lubricate the following internal components:
zcylinder block cylinder walls
z pistons and piston, pin and rings (6102)
z intake and exhaust valve stems
z intake and exhaust valve guides
z all internal engine components
When the pistons move downward, a thin film of oil is left on the cylinder walls. As the vehicle is
operated, some oil is also drawn into the combustion chambers past the intake and exhaust valve
stem seals and burned.
The following is a partial list of conditions that can affect oil consumption rates:
zengine duty cycle
z operator driving habits
z ambient temperature
z quality and viscosity of the oil
Operation under varying conditions can frequently be misleading. A vehicle that has been run for
several thousand miles on short trips or in below- freezing ambient temperatures may have consumed
a "normal" amount of oil. However, when checking the engine oil level, it may measure up to the FULL
or MAX on the oil level dipstick due to dilution (condensation and fuel) in the engine crankcase. The
vehicle might then be driven at high speeds on the highway where the condensation and fuel boil off.
The next time the engine oil is checked, it may appear that a liter (quart) of oil was used in about 160
km (100 miles). This perceived 160 km (100 miles) per liter (quart) oil consumption rate causes
customer concern even though the actual overall oil consumption rate is about 2,400 km (1,500 miles)
per liter (quart).
Make sure the selected engine oil meets the current recommended API performance category with
SAE viscosity grade as shown in the vehicle Owner's Guide. It is also important that the engine oil is
changed at the intervals specified. Refer to the vehicle Owner's Guide.
Oil Pressure Test
1. Disconnect and remove the oil pressure sensor (9278) from the engine.
2. Connect the Oil Pressure Gauge to the oil pressure sender oil galley port.
3. Run the engine until normal operating temperature is reached.
4. Run the engine at the specified rpm and record the gauge reading.
5. The oil pressure should be within specifications; refer to the specification chart in the appropriate engine section.
6. If the pressure is not within specification, check the following possible sources: zinsufficient oil
z oil leakage
z worn or damaged oil pump
z oil pump screen cover and tube (6622)
z excessive main bearing clearance Klj . 13 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
incorrectly functioning valve tappet
z air in lubrication system
z excessive valve guide wear
z low oil pressure
Excessive collapsed valve tappet gap can be caused by loose rocker arm seat bolts/nuts, incorrect
initial adjustment or wear of valve tappet face, or worn roller valve tappets, push rod (6565), rocker
arm (6564), rocker arm seat or valve tip. With valve tappet collapsed, check gap between the valve tip
and the rocker arm to determine if any other valve train parts are damaged, worn or out of adjustment.
An incorrectly functioning valve tappet can be sticking, caused by contaminants or varnish inside the
tappet. The tappet can have a check valve that is not functioning correctly, which can be caused by an
obstruction, such as dirt or chips that prevent the check valve from closing, or a broken check valve
spring. A tappet with a leakdown time out of specification can cause tappet noise. If no other cause for
noisy valve tappets can be found, the leakdown rate should be checked and new valve tappets
installed if found to be out of specification.
Assembled valve tappets can be tested with Hydraulic Tappet Leakdown Tester to check the leakdown
rate. The leakdown rate specification is the time in seconds for the plunger to move a specified
distance while under a 22.7 kg (50 lb) load.
Air bubbles in the lubrication system will prevent the valve tappet from supporting the valve spring
load. This can be caused by too high or too low an oil level in the oil pan or by air being drawn into the
system through a hole, crack or leaking gasket on the oil pump screen cover and tube. Klj . 17 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Engine
Refer to
Section 303 - 00 for basic mechanical concerns or refer to the Powertrain Control/Emissions
Diagnosis (PC/ED) manual for driveability concerns. SECTION 303-
01A: Engine — 3.8L 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Engine
For basic mechanical concerns, refer to
Section 303 - 00 . Refer to the Powertrain Control/Emissions
Diagnosis (PC/ED) manual. SECTION 303-
01B: Engine — 4.6L (2V) 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Engine
Refer to
Section 303 - 00 for basic mechanical concerns or refer to the Powertrain Control/Emissions
Diagnosis (PC/ED) manual for driveability concerns. SECTION 303-
01C: Engine — Cobra 4.6L (4V) 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Engine
Refer to
Section 303 - 00 for basic mechanical concerns or refer to the Powertrain Control/Emissions
Diagnosis (PC/ED) manual for driveability concerns. SECTION 303-
01D: Engine — Mach I 4.6L (4V) 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
SECTION 303-
03A: Engine Cooling 2003 Mustang Workshop Manual General Specifications
Item Specification
Cooling System Capacity 15.2 L (4.0 gal)
Coolant Type
Motorcraft Premium Gold Engine Coolant VC-7-
A in
(Oregon VC -7-B) (yellow color) WSS-
M97B51- A1 Other Chemicals
Motorcraft Premium Cooling System Flush VC-
1 ESR-
M14P7-A Premium Long Life Grease XG-1-
C ESA-
M1C75- B Cooling System Stop Leak Pellets
VC-
6 ESE-
M99B37- B5 except as noted in ES-
F65E-19A511- AA Gasket Adhesive TA-
6 WSS-
M2G408- A Cooling System Pressure Test Specifications 138 kPa (20 psi)
Radiator Cap Pressure Test Specifications 110 kPa (16 psi)
Thermostat Opening Temperatures
Starts to open (4.6L 2V) 87-
93°C (192- 199°F) Starts to open (3.8L) 86.7-
90.6°C (189- 196°F) Starts to open (Cobra) 80-
83°C (175- 182°F) Fully open 104°C (219°F)
Torque Specifications Description Nm lb-
ft lb-
in Accelerator cable bracket bolts 10 — 89
Cylinder block drain plug 20 15 —
Exhaust manifold to EGR valve tube nut 35 26 —
Fan shroud bolts 10 — 89
Fan motor bolts 10 — 89
Degas bottle nuts 10 — 89
Coolant expansion tank bracket bolts 10 — 89
Radiator support bracket bolts 30 22 —
Transmission fluid cooler fittings 30 22 —
Coolant outlet connection bolts (3.8L) 10 — 89
Bypass tube bracket bolts (3.8L) 10 — 89
Bypass tube bolts (4.6L) 10 — 89
Bypass tube nuts (Supercharged engine) 25 18 —
Coolant hose mounting bolt 25 18 — Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...