2003 FORD MUSTANG Oil pan

39. Position the crankshaft sensor ring on the crankshaft.
40. Install the oil pan and gasket and loosely install the bolts.
41. Tighten the bolts in the sequence shown.
zTighten to 20 Nm (15 lb- ft).
z Rotate an additional 60 degrees.
42. Install the drain plugs Klj . 14 ba
302003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

45. Tighten the four oil pan bolts in the sequence shown.
zStage 1: Tighten to 2 Nm (18 lb- in).
z Stage 2: Tighten to 20 Nm (15 lb- ft).
z Stage 3: Tighten an additional 60 degrees.
46. Install oil filter adapter. 1. Position the gasket.
2. Position the oil filter adapter.
3. Tighten the bolts.
4. Install a new oil filter. 1 N806177 Bolt, Hex Flange Head Pilot, M8 x 1.25 x 53
2 N806177 Bolt, Hex Flange Head Pilot, M8 x 1.25 x 53
3 N806177 Bolt, Hex Flange Head Pilot, M8 x 1.25 x 53
4 N806177 Bolt, Hex Flange Head Pilot, M8 x 1.25 x 53
5 N806177 Bolt, Hex Flange Head Pilot, M8 x 1.25 x 53
6 W706508 Stud, Hex Shldr Pilot, M8 x 1.25 x 50 —
M6 x 1 x
10 7 N808586 Stud and Washer, Hex-
Head Pilot, M8 x 1.25 x 60
— M6 x 1 x 26 8 N806177 Bolt, Hex Flange Head Pilot, M8 x 1.25 x 53
9 N806177 Bolt, Hex Flange Head Pilot, M8 x 1.25 x 53
10 N806177 Bolt, Hex Flange Head Pilot, M8 x 1.25 x 53
11 N806300 Stud, Hex Shldr Pilot, M8 x 1.25 x 65 —
M8 x 1.25
x 26 12 W706560 Stud, Hex-
Head Pilot, M8 x 1.25 x 65 — M8 x
1.25 x 16 13 N806300 Stud, Hex Shldr Pilot, M8 x 1.25 x 65 —
M8 x 1.25
x 26 14 N806300 Stud, Hex Shldr Pilot, M8 x 1.25 x 65 —
M8 x 1.25
x 26 15 N806300 Stud, Hex Shldr Pilot, M8 x 1.25 x 65 —
M8 x 1.25
x 26 Klj . 16 ba
302003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

80. Remove the engine from the stand.
81.
NOTE: If not secured within four minutes, the sealant must be removed and the sealing area
cleaned with metal surface cleaner. Allow to dry until there is no sign of wetness, or four
minutes, whichever is longer. Failure to follow this procedure can result in future oil leakage.
Apply a 4 mm (0.16 in) bead of silicone gasket and sealant around the rear oil seal retainer
plate sealing surface. Also apply a bead of silicone gasket and sealant at the junction where the
cylinder block, oil pan and rear oil seal retainer plate meet.
82. Install the rear oil seal retainer plate. Tighten the bolts in the sequence shown. zTighten the bolts to 1- 6 to 10 Nm (89 lb-in).
z Hand- tighten bolts 7 and 8.
z Tighten bolts 7 and 8 to 20 Nm (15 lb- ft).
z Tighten bolts 7 and 8 an additional 60 degrees. Klj . 27 ba
302003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Engine Cooling
CAUTION: Vehicle cooling systems are filled with Motorcraft Premium Gold Engine
Coolant VC -7-A (in Oregon VC -7-B) or equivalent meeting Ford specification WSS- M97B51-A1
(yellow color). Always fill the cooling system with the same coolant that is present in the
system. Do not mix coolant types.
NOTE: The addition of Motorcraft Cooling System Stop Leak Pellets, VC- 6, darkens Motorcraft
Premium Gold Engine Coolant from yellow to golden tan.
The 4.6L cooling system components include the:
zblock heater
z engine coolant temperature (ECT) sensor
z fan blade, fan motor and fan shroud assembly
z radiator
z pressure relief cap
z radiator draincock
z coolant pump
z coolant thermostat
z oil filter adapter
z radiator overflow hose
z upper radiator hose
z lower radiator hose
The radiator overflow hose circulates the coolant.
The coolant thermostat:
zcontrols the engine coolant temperature.
z allows for quicker engine warm- up.
The degas bottle/coolant expansion tank:
zprovides a location for service fill.
z contains coolant expansion and system pressurization.
z provides air separation during operation.
z replenishes the engine coolant to the system.
The engine coolant flows:
zfrom the lower radiator hose to the coolant pump.
z from the coolant pump to the engine block and the cylinder heads.
SECTION 303-
03A: Engine Cooling 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

The 3.8L cooling system components include the:
zblock heater
z engine coolant temperature (ECT) sensor
z fan blade, fan motor and fan shroud assembly
z radiator
z radiator cap
z radiator draincock
z coolant pump
z coolant thermostat
z oil filter adapter
z radiator overflow hose
z coolant expansion tank
z upper radiator hose
z lower radiator hose
The fan blade draws air through the radiator to help cool the engine coolant.
The fan motor:
zoperates only when the ignition switch is in the RUN position.
z will not operate with the switch in the OFF position.
The engine coolant:
zflows through the radiator tubes and is cooled by passing air over the cooling fins.
z is then circulated from the radiator outlet tank through the coolant pump and into the cylinder
block to complete the circuit.
A closed coolant thermostat returns the engine coolant to the coolant pump. An open coolant
thermostat allows the engine coolant to flow to the radiator.
CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency,
and corrosion protection to the engine and cooling components. In order to obtain these
protections, the engine coolant must be maintained at the correct concentration and fluid level
in the degas bottle (4.6L) or coolant expansion tank (3.8L).
When adding engine coolant, use a 50/50 mixture of engine coolant and deionized water.
To maintain the integrity of the coolant and the cooling system:
zNOTE: The addition of Motorcraft Cooling System Stop Leak Pellets, VC-6, darkens Motorcraft
Premium Gold Engine Coolant from yellow to golden tan.
Add Motorcraft Premium Gold Engine Coolant VC-7- A (in Oregon VC-7-B) or equivalent
meeting Ford specification WSS- M97B51-A1 (yellow color). Use the same coolant that is
present in the cooling system. Do not mix coolant types.
z Do not add/mix orange-colored Motorcraft Speciality Orange Engine Coolant VC- 2 or equivalent Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

3. If the inspection reveals an obvious concern that can be readily identified, repair as necessary.
4.
CAUTION: Some vehicle cooling systems are filled with Motorcraft Premium Gold
Engine Coolant VC -7-A (in Oregon VC -7-B) or equivalent meeting Ford specification
WSS- M97B51- A1 (yellow color). Always fill the cooling system with the same coolant that
is present in the system. Do not mix coolant types.
NOTE: The addition of Motorcraft Cooling System Stop Leak Pellets, VC-6, darkens Motorcraft
Premium Gold Engine Coolant from yellow to golden tan.
Inspect the coolant condition. 1. Inspect the coolant color.
„If Motorcraft Premium Gold Engine Coolant (yellow color) VC-7- A (in Oregon VC-
7- B) or equivalent meeting Ford specification WSS-M97B51- A1 has a clear or
pale yellow color, this indicates higher water content than required.
„ Dark brown can indicate unauthorized stop leak may have been used. Use
Motorcraft Cooling System Stop Leak Pellets VC- 6 or equivalent meeting Ford
specification ESE-M99B37- 5 except as noted in ES-F6SE-19A511- AA only.
„ A light or reddish brown color indicates that rust may be present in the cooling
system. Flush the system and refill with the correct mixture of water and engine
coolant.
„ An iridescent sheen on top of the coolant can indicate a trace of oil is entering the
system. For additional information on engine diagnosis, refer to Section 303 - 00 .
„ A milky brown color may indicate that either engine oil or transmission fluid is
entering the cooling system. If transmission fluid is suspected, the cause may be a
leaky radiator. Pressure test the cooling system. For additional information, refer
to component tests in this section. If engine oil is suspected the cause of the leak
may be internal to the engine. For additional information, refer to Section 303 - 00 .
2. If the engine coolant appearance is acceptable, test the engine coolant freezing point
range with the battery and anti- freeze tester. The freezing point should be in the range -
40°C to - 20°C (-50°F to - 10°F). If the vehicle is driven in cold climates less than - 32°C (-
34°F), it may be necessary to increase the coolant concentration to get adequate freeze
protection.
„Maximum coolant concentration is 60% coolant/40% water.
„ Minimum coolant concentration is 40% coolant/60% water. 3. Adjust coolant range and level, if necessary: Visual Inspection Chart
Mechanical
z
Leaks
z Hoses
z Hose clamps
z Water gasket
z Head gaskets
z Intake manifold gasket
z Coolant pump
z Radiator
z Degas bottle/coolant expansion tank
z Heater core
z Fan/fan clutch
z Engine coolant temperature sensor (4.6L)
z Cylinder head temperature sensor (3.8L)
z Circuitry Klj . 2 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

while the pressure is released from the cooling system.
When you are sure all the pressure has been released, turn
and remove the pressure relief cap (still with a cloth).
NOTE:
Allow the engine to cool before checking the engine
coolant level.
z Key in OFF position.
z Visually check the engine coolant level at the degas bottle or
coolant expansion tank.
z Is the engine coolant level within specification? A2 CHECK THE PRESSURE RELIEF CAP
z
Carry out the Cap— 3.8L or Cap—4.6L test. Go to Component
Tests in this section.
z Is pressure relief cap/radiator cap OK? Yes
GO to
A3 .
No
INSTALL a new
pressure relief
cap/radiator cap. TEST
the system for normal
operation. A3 CHECK THE ENGINE COOLANT FOR INTERNAL LEAK
z
Key in OFF position.
z Inspect the engine coolant in degas bottle/coolant expansion
tank for signs of transmission fluid or engine oil.
z Is oil or transmission fluid evident in the coolant? Yes
If engine oil is evident,
REFER to
Section 303 -
00 . If transmission fluid
is evident, REPAIR or
INSTALL a new radiator
as necessary.
No
GO to A4 .
A4 CHECK THE ENGINE AND THE TRANSMISSION FOR
COOLANT z
Remove the oil level dipstick from the engine and the
transmission.
z Is coolant evident in the oil or transmission fluid? Yes
If coolant is in engine,
REFER to
Section 303 -
00 . If coolant is in
transmission, REPAIR
or INSTALL a new
radiator as necessary.
To repair the automatic
transmission, REFER to
Section 307 - 01 .
No
GO to A5 .
A5 PRESSURE TEST THE ENGINE COOLING SYSTEM
z
Pressure test the engine cooling system. Go to Component
Tests in this section.
z Does the engine cooling system leak? Yes
REPAIR or install new
components. TEST the
system for normal
operation.
No
The cooling system is
operational. GO to
Symptom Chart
. Klj . 4 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Supercharger Cooling
CAUTION: Some vehicle cooling systems are filled with Motorcraft Premium Engine
Coolant VC -4-A (in Oregon VC- 5, in Canada CXC- 10) or equivalent meeting Ford specification
ESE- M97B44- A (green color). Others are filled with Motorcraft Premium Gold Engine Coolant
VC -7-A or equivalent meeting Ford specification WSS- M97B51-A1 (yellow color). Always fill the
cooling system with the same coolant that is present in the system. Do not mix coolant types.
NOTE: The addition of Motorcraft Cooling System Stop Leak Pellets, VC- 6, darkens Motorcraft
Premium Gold Engine Coolant from yellow to golden tan.
NOTE: The air that is produced from the supercharger is cooled by the intercooler.
Walter C. Avrea, the owner of patents 3,601,181 and RE 27,965, has granted Ford Motor Company
rights with respect to cooling systems covered by these patents.
The cooling system components include the:
zintercooler
z intercooler radiator (8K226)
z pressure relief cap
z degas bottle
z electric water pump (8501)
The degas bottle:
zprovides a location for system fill.
z contains coolant expansion and system pressurization.
z provides air separation during operation.
z replenishes the intercooler coolant to the system.
The intercooler coolant flows:
zfrom the intercooler to the degas bottle.
z from the degas bottle to the water pump.
z from the water pump to the intercooler radiator.
z from the intercooler radiator to the intercooler.
Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to
the engine and cooling components. In order to obtain these protections, the engine coolant must be
maintained at the correct concentration and fluid level in the degas bottle.
When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water.
To maintain the integrity of the coolant and the cooling system: SECTION 303-
03B: Supercharger Cooling 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...