2003 FORD MUSTANG coolant level

z
Engine oil fluid level.
z Windshield washer solvent fluid level.
z Check and drain fuel/water separator.
Six Month Checks
Check each of the following items at least every six months:
zLap/shoulder belts and seat latches for wear and function.
z Spare tire air pressure.
z Power steering fluid level.
z Parking brake for correct operation.
z Safety warning lamps (brake, ABS, air bag, safety belt) for correct operation.
z Coolant system fluid level and correct strength.
z Battery connections. Clean if necessary.
z Clutch fluid level, if equipped.
z Windshield washer spray, wiper operation, clean all wiper blades.
z Lubricate all hinges, latches and outside locks. Inspect for correct operation.
z Lubricate door rubber weatherstrips. Inspect for excessive wear.
z Clean body and door drain holes. Inspect for clogs and obstructions.
Special Checks (Mustang Only)
Carry out the following check every 8,000 km (5,000 miles):
zAdjust clutch by lifting pedal (manual transmission Mustang only, as described in owner guide).
Normal Schedule
The following checks or procedures should be carried out for all cars, minivans, light trucks, sport
utilities, vans, 4x4s, natural gas and propane vehicles.
8,000 Km (5,000 Miles) zChange engine oil and install a new oil filter.
z Rotate tires and inspect for wear.
16,000 Km (10,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
24,000 Km (15,000 Miles)
zChange engine oil and install a new oil filter. Klj . 3 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Change engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
64,000 Km (40,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
72,000 Km (45,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect automatic transmission fluid level using dipstick, if equipped.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z If equipped, install a new cabin air filter.
z If filled with green engine coolant, change coolant.
80,000 Km (50,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
z Drain coalescent fuel filter and replace filter (NGV).
88,000 Km (55,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
96,000 Km (60,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new engine air filter.
z Install a new fuel filter. (See ADDITIONAL INFORMATION below.)
z If equipped, install a new cabin air filter.
z Change automatic transmission/transaxle fluid on all vehicles equipped with AX4S, 4F50N,
4R100, 4F27E. Inspect automatic transmission fluid level using dipstick on all other vehicles, if Klj . 5 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

equipped.
z If equipped, install new climate controlled seat filters (Navigator, Lincoln LS and Aviator).
ADDITIONAL INFORMATION: If vehicle is registered in California, the California Air Resources Board
(CARB) has determined that failure to install a new fuel filter at this interval will not nullify the emission
warranty or limit recall liability prior to completion of the vehicle's useful life. It is, however,
recommended that maintenance checks be carried out and recorded at the indicated intervals.
Additional checks for natural gas and propane vehicles at this interval include inspecting fuel tanks, as
well as draining coalescent fuel filter and installing a new filter.
104,000 Km (65,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
112,000 Km (70,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
120,000 Km (75,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect automatic transmission fluid level using dipstick.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new cabin air filter.
z Drain coalescent fuel filter and replace filter (NGV).
z Change green engine coolant, if equipped.
128,000 Km (80,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
136,000 Km (85,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
144,000 Km (90,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system. Klj . 6 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect exhaust system and heat shields.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new engine air filter.
z Install a new fuel filter.
z If equipped, install a new cabin air filter.
z Change automatic transmission/transaxle fluid on all vehicles equipped with AX4S, 4F50N,
4R100, 4F27E. Inspect automatic transmission fluid level using dipstick on all other vehicles, if
equipped.
z If equipped, install new climate controlled seat filters (Navigator, Lincoln LS and Aviator).
Additional services for natural gas and propane vehicles include inspecting fuel tanks, as well as
draining coalescent fuel filter bowl and installing a new filter.
152,000 Km (95,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
160,000 Km (100,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect accessory drive belt(s).
z Rotate tires and inspect for wear.
z Install new spark plugs.
z If filled with yellow coolant, change coolant or at 5 years, whichever comes first.
z Install a new PCV on all cars and light trucks under 6,000 pounds Gross Vehicle Weight (GVW).
z Drain coalescent fuel filter and replace filter (NGV).
168,000 Km (105,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect automatic transmission fluid level if equipped with dipstick.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine coolant system and hoses.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z If equipped, install a new cabin air filter.
z If filled with green engine coolant, change coolant. 176,000 Km (110,000 Miles) Klj . 7 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
If equipped, inspect automatic transmission fluid level with dipstick.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new cabin air filter.
z If filled with green engine coolant, change coolant.
224,000 Km (140,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
232,000 Km (145,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
240,000 Km (150,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect exhaust system and heat shields.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new engine air filter.
z Install a new fuel filter. (See ADDITIONAL INFORMATION below.)
z If equipped, install a new cabin air filter.
z If filled with yellow engine coolant, change coolant or at 8 years, whichever comes first.
z Change automatic transmission/transaxle fluid and filter.
z Change rear axle lubricant on all rear wheel (RWD) vehicles.
z Install a new accessory drive belt(s) (if a new belt has not been installed within the last 100,000
miles).
z If equipped, install new climate controlled seat filters (Navigator, Lincoln LS and Aviator).
ADDITIONAL INFORMATION: If vehicle is registered in California, the California Air Resources Board
(CARB) has determined that failure to install a new fuel filter at this interval will not nullify the emission
warranty or limit recall liability prior to completion of the vehicle's useful life. It is, however
recommended that maintenance checks be carried out and recorded at the indicated intervals.
Additional checks for natural gas and propane vehicles include inspecting fuel tanks, as well as
draining and installing a new filter. Klj . 9 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

noise—
normally
accompanied by
vibration Powertrain/Drivetrain Mount Neutralizing in this
section.
z Damaged or
misaligned exhaust
system. z
INSPECT the exhaust
system for loose or broken
clamps and brackets.
CARRY OUT Exhaust System Neutralizing in this
section.
z Whistling noise—
normally
accompanied
with poor idle
condition z
Air intake system. zCHECK the air intake
ducts, air cleaner, throttle
body and vacuum hoses for
leaks and correct fit.
REPAIR or ADJUST as
necessary. REFER to
Section 303 - 12
z
Clunking noise zWater pump has
excessive end play or
imbalance. z
CHECK the water pump for
excessive end play.
INSPECT the water pump
with the drive belt off for
imbalance. INSTALL a new
water pump as necessary.
REFER to Section 303 -
03A .
z Generator has
excessive end play. z
CHECK the generator for
excessive end play.
REPAIR or INSTALL a new
generator. REFER to
Section 414 - 02 .
z Pinging noise zExhaust system leak. zINSPECT the exhaust
system for leaks. REPAIR
as necessary.
z Gasoline octane too
low. z
VERIFY with customer the
type of gasoline used.
CORRECT as necessary.
z Knock sensor
operation. z
CHECK the knock sensor.
INSTALL a new knock
sensor as necessary.
REFER to Section 303 - 14 .
z Incorrect spark
timing. z
CHECK the spark timing.
REPAIR as necessary.
z High operating
temperature. z
INSPECT cooling system
for leaks. CHECK the
coolant level. REFILL as
necessary. CHECK the
coolant for the correct mix
ratio. DRAIN and REFILL
as needed. CHECK engine
operating temperature is
within specifications.
REPAIR as necessary.
z Foul- out spark plug. zCHECK the spark plugs.
REPAIR or INSTALL new
spark plugs as necessary.
z Catalytic converter. zAcceptable noise.
z Knocking noise—
light knocking
noise, also z
Excessive clearance
between the piston
and the cylinder wall. z
Engine cold and at high
idle. Using an EngineEAR,
pull a spark plug or fuel Klj . 24 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1. If compression improves considerably, piston rings are faulty.
2. If compression does not improve, valves are sticking or seating incorrectly.
3. If two adjacent cylinders indicate low compression pressures and squirting oil on each piston
does not increase compression, the head gasket may be leaking between cylinders. Engine oil
or coolant in cylinders could result from this condition.
Use the Compression Pressure Limit Chart when checking cylinder compression so that the
lowest reading is within 75 percent of the highest reading.
Cylinder Leakage Detection
When a cylinder produces a low reading, use of the Engine Cylinder Leak Detection/Air Pressurization
Kit will be helpful in pinpointing the exact cause.
The leakage detector is inserted in the spark plug hole, the piston is brought up to dead center on the
compression stroke, and compressed air is admitted.
Once the combustion chamber is pressurized, a special gauge included in the kit will read the
percentage of leakage. Leakage exceeding 20 percent is excessive.
While the air pressure is retained in the cylinder, listen for the hiss of escaping air. A leak at the intake
valve (6507) will be heard in the throttle body (9E926). A leak at the exhaust valve (6505) can be
heard at the tail pipe. Leakage past the piston rings will be audible at the positive crankcase ventilation
(PCV) connection. If air is passing through a blown head gasket to an adjacent cylinder, the noise will
be evident at the spark plug hole of the cylinder into which the air is leaking. Cracks in the cylinder
block or gasket leakage into the cooling system may be detected by a stream of bubbles in the radiator
(8005).
Oil Consumption Test
The following diagnostic procedure is used to determine the source of excessive internal oil
consumption. 1. NOTE: Oil use is normally greater during the first 16,100 km (10,000 miles) of service. As
mileage increases, oil use generally decreases. Vehicles in normal service should get at least
1,450 km per liter (900 miles per quart) after 16,000 km (10,000 miles) of service. High speed
driving, towing, high ambient temperature and other factors may result in greater oil use.
Define excessive oil consumption, such as the number of miles driven per liter (quart) of oil
used. Also determine customer's driving habits, such as sustained high speed operation,
towing, extended idle and other considerations.
2. Verify that the engine has no external oil leak as described under Engine Oil Leaks in the Diagnosis and Testing portion of this section.
3. Verify that the engine has the correct oil level dipstick (6750).
4. Verify that the engine is not being run in an overfilled condition. Check the oil level at least five minutes after a hot shutdown with the vehicle parked on a level surface. In no case should the
level be above MAX or the letter F in FULL. If significantly overfilled, carry out Steps 6a through
6d.
5. Verify the spark plugs are not oil saturated. If the spark plugs are oil saturated and compression is good it can be assumed the valve seals or valve guides are at fault. Klj . 9 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

A/C compressor bracket-
to-cylinder head stud bolt 25 18 —
Oil level indicator tube-
to-cylinder head bolt 10 — 89
Coolant recovery reservoir bracket-to-
GOP bolts 9 — 80
Motor mount-
to-subframe nuts 115 85 —
Oil pan drain plug 26 19 —
Wire harness bracket to motor mount nut 27 20 —
Steering column pinch bolt 47 35 —
Front subframe-
to-body bolts 90 66 —
Front subframe-
to-shock tower bolts 115 85 —
Oil pan-to-
cylinder block bolts a — — —
Oil pan-to-
transmission bell housing 45 33 —
Main bearing bridge nuts 32 24
Oil pump cover-
to-engine front cover bolts 25 18 —
Oil pump cover-
to-engine front cover bolt 10 89 —
Oil pickup tube-
to-cylinder block bolts 25 18 —
Oil pickup tube-
to-oil pan baffle nut 48 35 —
Flywheel-
to-crankshaft bolts 80 59 —
Wire harness bracket-
to-motor mount stud- nut 27 20 —
Engine ground strap-
to-motor mount nut 27 20 —
Motor mount-
to-motor mount bracket bolts 70 52 —
RH motor mount-
to-motor mount bracket nut 70 52 —
Hood ground strap-
to-hood hinge bolt 12 9 —
Hood hinge nuts 12 9 —
Generator mounting bracket 25 18 —
Power steering pump bracket nuts 8 — 71
Power steering pump bolts 25 18 —
Valve tappet guide plate bolts 12 9 —
Generator positive cable nut 10 — 89
Power steering pressure tube to pump nut 40 30 —
Accelerator cable bracket-
to-intake manifold bolts 10 — 89
42-
pin connector bolt 10 — 89
Transmission oil cooler tube bracket-
to-motor mount bracket nut 27 20
Torque converter-
to-flywheel nuts 36 27 —
Engine-
to-transmission bolts 40 30 —
Engine mount bracket-
to-engine bolts 70 52 —
Engine mount bracket-
to-engine nuts 70 52 —
Water pump pulley bolts 25 18 —
Oil filter
b — — —
Upper intake manifold-
to-lower intake manifold bolts a — — —
Lower intake manifold-
to-cylinder head bolts a — — —
Rocker arm pivot-
to-cylinder head bolts a — — — Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...