2003 DODGE RAM maintenance schedule

FUEL FILTER / WATER
SEPARATOR
DESCRIPTION
The fuel filter/water separator assembly is located
on left side of engine above starter motor. The assem-
bly also includes the fuel heater and Water-In-Fuel
(WIF) sensor, and fuel transfer pump.
OPERATION
The fuel filter/water separator protects the fuel
injection pump by removing water and contaminants
from the fuel. The construction of the filter/separator
allows fuel to pass through it, but helps prevent
moisture (water) from doing so. Moisture collects at
the bottom of the canister.
Refer to the maintenance schedules for the recom-
mended fuel filter replacement intervals.
For draining of water from canister, refer to Fuel
Filter/Water Separator Removal/Installation section.A Water-In-Fuel (WIF) sensor is attached to side of
canister. Refer to Water-In-Fuel Sensor Description/
Operation.
The fuel heater is installed into the top of the fil-
ter/separator housing. Refer to Fuel Heater Descrip-
tion/Operation.
REMOVAL
Refer to maintenance schedules in this manual for
recommended fuel filter replacement intervals.
Draining water from fuel filter/water separa-
tor housing:
The housing drain valve (Fig. 3) or (Fig. 4) serves
two purposes. One is topartiallydrain filter hous-
ing of excess water. The other is tocompletelydrain
housing for fuel filter, drain valve, heater element, ,
water-in-fuel sensor replacement or transfer pump
replacement.
The filter housing should be partially drained
whenever water-in-fuel warning lamp remains illumi-
nated. (Note that lamp will be illuminated for
approximately two seconds when ignition key is ini-
tially placed in ON position for a bulb check).
(1) A drain hose (Fig. 3) or (Fig. 4) is located at
bottom of drain valve. Place drain pan under drain.
(2)With engine not running,rotate drain valve
handle rearward to OPEN (DRAIN) position. Hold
drain valve open until all water and contaminants
have been removed and clean fuel exits.
(3) If drain valve, fuel heater element or Water-In-
Fuel (WIF) sensor is being replaced, drain housing
completely. Dispose of mixture in drain pan according
to applicable regulations.
(4) After draining operation, push valve handle
forward to CLOSE position.
(5)Fuel Filter Replacement:The fuel filter is
located inside of the fuel filter housing.
(a) Clean all debris from around canister.
(b) Remove filter lid (Fig. 5) using a socket.
Attach socket to large hex on top of lid (Fig. 5).
Rotate counter-clockwise for removal. Remove
o-ring.
(c) Remove filter element by twisting element
sideways from filter lid.
(6)Water-In-Fuel (WIF) Sensor Replacement:
The WIF sensor is located on the side of the fuel fil-
ter housing (Fig. 3) or (Fig. 4).
(a) Disconnect electrical connector at sensor.
(b) Clean area around sensor.
(c) Remove sensor by rotating counter-clockwise.
(d) Check condition of sensor o-ring. Replace if
damaged.
(7)Fuel Heater Element Replacement:The
heater element is located in the fuel filter housing
(Fig. 3) or (Fig. 4).
(a) Remove fuel filter. See previous steps.
FUEL INJECTOR TUBE (CONNECTOR) REMOVER -
#9015
SPANNER WRENCH (FUEL TANK MODULE
REMOVAL/INSTALLATION) - #6856
ENGINE ROTATING (BARRING) TOOL - #7471B
(ALSO PART OF KIT #6860)
DRFUEL DELIVERY - DIESEL 14 - 61
FUEL DELIVERY - DIESEL (Continued)

(b) Disconnect electrical connector.
(c) Remove two T-15 Torx head mounting screws
from fuel heater element.
(d) Remove fuel filter cover and filter element.
(e) Remove fuel heater.
(8)Drain Valve Replacement:The drain valve
assembly is located on the side of the fuel filter hous-
ing (Fig. 3) or (Fig. 4).
(a) Disconnect drain hose from the fuel drain
valve.
(b) Remove 4 drain valve mounting screws (T-15
Torx head).
(c) Remove drain valve from filter housing.
INSTALLATION
Refer to maintenance schedules for recommended
fuel filter replacement intervals.
(1) Thoroughly clean inside of filter housing, filter
cap and all related components.
(2)Fuel Filter:
(a)The engine has a self-priming low-pres-
sure fuel system. Refer to Standard Proce-
dures-Fuel System Priming.
(b) Install new o-ring to canister lid and lubri-
cate o-ring with 30W oil.
Fig. 3 FILTER HOUSING (EARLY)
1 - FILTER HOUSING
2 - FUEL HEATER AND THERMOSTAT
3 - FUEL HEATER MOUNTING SCREWS
4 - FUEL HEATER ELEC. CONNECTOR
5 - DRAIN VALVE
6 - DRAIN VALVE MOUNTING SCREWS
7 - DRAIN HOSE
8 - WIF SENSOR
9 - WIF SENSOR ELEC. CONNECTOR
Fig. 4 FILTER HOUSING (LATE)
1 - FILTER HOUSING
2 - FUEL HEATER AND THERMOSTAT
3 - FUEL HEATER MOUNTING SCREWS
4 - FUEL HEATER ELEC. CONNECTOR
5 - WIF SENSOR
6 - WIF SENSOR ELEC. CONNECTOR
7 - DRAIN HOSE
8 - DRAIN VALVE MOUNTING SCREWS
9 - DRAIN VALVE
Fig. 5 FILTER COVER (LID)
1 - FILTER COVER
2 - ATTACH SOCKET HERE
14 - 62 FUEL DELIVERY - DIESELDR
FUEL FILTER / WATER SEPARATOR (Continued)

STANDARD PROCEDURE - LUBRICATION
Periodic lubrication of the steering system compo-
nents is required. Refer to Lubrication And Mainte-
nance for the recommended maintenance schedule.
The following components must be lubricated:
²Tie rod
²Tie rod end
²Drag link
SPECIFICATIONS
TORQUE CHART
TORQUE SPECIFICATIONS
DESCRIPTION N´m Ft. Lbs. In. Lbs.
Pitman Arm
Gear Shaft Nut300 225 Ð
Drag Link
Pitman Arm88 65 Ð
Drag Link
Tie Rod108 80 Ð
Drag Link
Adjuster Clamp61 45 Ð
Tie Rod End
Knuckle108 80 Ð
Tie Rod End
Adjuster Clamp61 45 Ð
Stabilizer Bar Link to Axle 68 50 Ð
Steering Damper
Axle95 70 Ð
Steering Damper
Tie Rod81 60 Ð
Fig. 2 Ball Stud Puller
1 - CLAMP
2 - ADJUSTMENT SLEEVE
3 - PULLER TOOL C-3894±A
4 - SEAL
5 - TIE-ROD END
19 - 34 LINKAGE - LINK/COILDR
LINKAGE - LINK/COIL (Continued)

METHOD 2 (RELOCATE TIRE ON WHEEL)
NOTE: Rotating the tire on wheel is particularly
effective when there is runout in both tire and
wheel.
(1) Remove tire from wheel and mount wheel on
service dynamic balance machine.
(2) Check wheel radial runout (Fig. 2) and lateral
runout (Fig. 3).
²STEEL WHEELS: Radial runout 0.031 in., Lat-
eral runout 0.031 in. (maximum)
²ALUMINUM WHEELS: Radial runout 0.020 in.,
Lateral runout 0.025 in. (maximum)
(3) If point of greatest wheel lateral runout is near
original chalk mark, remount tire 180 degrees.
Recheck runout, Refer to match mounting procedure.
STANDARD PROCEDURE
STANDARD PROCEDURE - TIRE ROTATION
Tires on the front and rear axles operate at differ-
ent loads and perform different steering, driving, and
braking functions. For these reasons, the tires wear
at unequal rates. They may also develop irregular
wear patterns. These effects can be reduced by rotat-
ing the tires according to the maintenance schedule
in the Owners Manual. This will improve tread life,
traction and maintain a smooth quiet ride.
The recommended method of tire rotation is (Fig.
4) & (Fig. 5). Other methods can be used, but may
not provide the same tire longevity benefits.
CAUTION: 3500 Dual rear tires have a new tire rota-
tion pattern. This is to accommodate the asymmet-rical design of the ON/OFF road tires and the use of
the outlined white letter (OWL) tires. When replac-
ing a flat, the spare tire may have to be remounted
on the rim or installed at a different location to
maintain the correct placement of the asymmetrical
design or the (OWL).
Fig. 1 Checking Tire/Wheel/Hub Runout
1 - RADIAL RUNOUT
2 - LATERAL RUNOUT
Fig. 2 Radial Runout
1 - MOUNTING CONE
2 - SPINDLE SHAFT
3 - WING NUT
4 - PLASTIC CUP
5 - DIAL INDICATOR
6 - WHEEL
7 - DIAL INDICATOR
Fig. 3 Lateral Runout
1 - MOUNTING CONE
2 - SPINDLE SHAFT
3 - WING NUT
4 - PLASTIC CUP
5 - DIAL INDICATOR
6 - WHEEL
7 - DIAL INDICATOR
22 - 2 TIRES/WHEELSDR
TIRES/WHEELS (Continued)

LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-54
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT................7-17
LEVEL CHECK - STANDARD
PROCEDURE, FLUID.....21-201,21-381,21-542
LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING FLUID . . . 19-42
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL..............14-68,14-7
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL..................14-8
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL................14-68,14-7
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL......................14-7
LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-9
LEVEL SWITCH - INSTALLATION,
WASHER FLUID.....................8R-11
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-9
LEVEL SWITCH - REMOVAL, WASHER
FLUID.............................8R-10
LEVER - ADJUSTMENT, SHIFT . . . 21-622,21-657
LEVER - INSTALLATION, GEAR SHIFT.....19-12
LEVER - INSTALLATION, SHIFT . . . 21-621,21-656
LEVER - REMOVAL, GEAR SHIFT........19-12
LEVER - REMOVAL, SHIFT......21-620,21-655
LICENSE PLATE LAMP - INSTALLATION . . . 8L-16
LICENSE PLATE LAMP - REMOVAL.......8L-16
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-16
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-16
LID - INSTALLATION, CENTER SEAT
BACK..............................23-80
LID - REMOVAL, CENTER SEAT BACK....23-80
LIFTERS - CLEANING, HYDRAULIC . . 9-260,9-388
LIFTERS - INSTALLATION, HYDRAULIC . . . 9-260,
9-388
LIFTERS - REMOVAL, HYDRAULIC . . 9-259,9-387
LIFTERS/TAPPETS - CLEANING, SOLID....9-328
LIFTERS/TAPPETS - INSPECTION, SOLID . . 9-328
LIFTERS/TAPPETS - INSTALLATION,
SOLID.............................9-328
LIFTERS/TAPPETS - REMOVAL, SOLID....9-327
LIGHT DUTY FRONT FRAME RAIL TIP
REPLACEMENT - STANDARD
PROCEDURE.........................13-4
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIMITING VALVE - DESCRIPTION, FUEL
PRESSURE.........................14-72
LIMITING VALVE - INSTALLATION, FUEL
PRESSURE.........................14-73
LIMITING VALVE - OPERATION, FUEL
PRESSURE.........................14-72
LIMITING VALVE - REMOVAL, FUEL
PRESSURE.........................14-72
LINE - DESCRIPTION, REFRIGERANT.....24-32
LINE - INSTALLATION, LIQUID..........24-45
LINE - REMOVAL, LIQUID..............24-45
LINE COUPLER - DESCRIPTION,
REFRIGERANT.......................24-52
LINE COUPLER - INSTALLATION,
REFRIGERANT.......................24-53
LINE COUPLER - OPERATION,
REFRIGERANT.......................24-52
LINE COUPLER - REMOVAL,
REFRIGERANT.......................24-52
LINE LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL................14-69
LINE PRESSURE (LP) SENSOR -
DESCRIPTION......................21-559
LINE PRESSURE (LP) SENSOR -
INSTALLATION......................21-560
LINE PRESSURE (LP) SENSOR -
OPERATION........................21-559
LINE PRESSURE (LP) SENSOR -
REMOVAL.........................21-559
LINES - DESCRIPTION, FUEL
.......14-69,14-8
LINES - DESCRIPTION, VACUUM
........25-22
LINES - INSTALLATION, FUEL
...........14-71
LINES - OPERATION, FUEL
.............14-69
LINES - OPERATION, REFRIGERANT
......24-32LINES - REMOVAL, FUEL..............14-69
LINK - INSTALLATION, DRAG...........19-35
LINK - REMOVAL, DRAG...............19-35
LINK CONNECTOR - DESCRIPTION, DATA . . 8E-3
LINK CONNECTOR - OPERATION, DATA....8E-3
LINKAGE - INSTALLATION...............6-13
LINKAGE - LINK/COIL - DESCRIPTION....19-33
LINKAGE - REMOVAL..................6-13
LINKAGE, SPECIAL TOOLS - STEERING . . . 19-35
LINK/COIL - DESCRIPTION, GEAR........19-19
LINK/COIL - DESCRIPTION, LINKAGE.....19-33
LINK/COIL - INSTALLATION, GEAR.......19-20
LINK/COIL - OPERATION, GEAR.........19-19
LINK/COIL - REMOVAL, GEAR...........19-19
LINK/COIL SUSPENSION - STANDARD
PROCEDURE, ALIGNMENT...............2-5
LIQUID LINE - INSTALLATION...........24-45
LIQUID LINE - REMOVAL..............24-45
LOAD FLOOR - INSTALLATION..........23-73
LOAD FLOOR - REMOVAL..............23-73
LOAD FLOOR SUPPORT CYLINDER -
INSTALLATION.......................23-73
LOAD FLOOR SUPPORT CYLINDER -
REMOVAL..........................23-73
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL.....8W-01-10
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE...................8W-91-1
LOCATIONS - SPECIFICATIONS, SEALER . 23-103
LOCATIONS - SPECIFICATIONS,
STRUCTURAL ADHESIVE..............23-113
LOCATIONS - SPECIFICATIONS, WELD . . . 23-122
LOCK - STANDARD PROCEDURE,
HYDROSTATIC........9-186,9-232,9-290,9-361
LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH AND KEY....19-11
LOCK CYLINDER - INSTALLATION.......23-24
LOCK CYLINDER - REMOVAL...........23-24
LOCK MOTOR - DESCRIPTION, DOOR.....8N-5
LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR......................8N-5
LOCK MOTOR - OPERATION, DOOR.......8N-5
LOCK SWITCH - DIAGNOSIS AND
TESTING, POWER.....................8N-4
LOCK SWITCH - INSTALLATION, POWER . . . 8N-4
LOCK SWITCH - REMOVAL, POWER......8N-4
LOCKING RETRACTOR - DESCRIPTION,
AUTOMATIC........................8O-13
LOCKING RETRACTOR - OPERATION,
AUTOMATIC........................8O-14
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-3
LOCKS - OPERATION, POWER...........8N-2
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-50
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-50
LOOP BRACKETS - INSTALLATION, SEAT
BACK REAR - FOOTMANS..............23-85
LOOP BRACKETS - REMOVAL, SEAT
BACK REAR - FOOTMANS..............23-85
LOW FUEL INDICATOR - DESCRIPTION . . . 8J-29
LOW FUEL INDICATOR - OPERATION.....8J-29
LOWER BALL JOINT - DIAGNOSIS AND
TESTING............................2-18
LOWER BALL JOINT - INSTALLATION . 2-19,2-33
LOWER BALL JOINT - REMOVAL.....2-18,2-32
LOWER CONTROL ARM BUSHINGS -
2WD (LD) - INSTALLATION..............2-14
LOWER CONTROL ARM BUSHINGS -
2WD (LD) - REMOVAL.................2-12
LOWER CONTROL ARM BUSHINGS -
4WD (LD) - INSTALLATION..............2-13
LOWER CONTROL ARM BUSHINGS -
4WD (LD) - REMOVAL.................2-12
LOWER SURROUND - INSTALLATION,
INSTRUMENT PANEL..................23-60
LOWER SURROUND - REMOVAL,
INSTRUMENT PANEL
..................23-60
LOWER SUSPENSION ARM -
INSTALLATION
........................2-35
LOWER SUSPENSION ARM - REMOVAL
....2-35
LOWER TRIM - INSTALLATION,
B-PILLAR
...........................23-65
LOWER TRIM - INSTALLATION,
C-PILLAR
...........................23-68LOWER TRIM - REMOVAL, B-PILLAR.....23-64
LOWER TRIM - REMOVAL, C-PILLAR.....23-67
LOW/REVERSE CLUTCH - ASSEMBLY....21-561
LOW/REVERSE CLUTCH - CLEANING....21-561
LOW/REVERSE CLUTCH - DISASSEMBLY . 21-560
LOW/REVERSE CLUTCH - INSPECTION . . 21-561
LUBRICANTS - DESCRIPTION, ENGINE
OIL .................................0-2
LUBRICATION - DESCRIPTION.....9-148,9-214,
9-267,9-337,9-393,9-60
LUBRICATION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS.....9-183,9-230,
9-358,9-7
LUBRICATION - OPERATION . 9-148,9-267,9-337,
9-393,9-60
LUBRICATION - STANDARD PROCEDURE . . 19-34
LUBRICATION - STANDARD PROCEDURE,
BODY...............................23-3
LUMBAR CONTROL SWITCH -
DESCRIPTION.......................8N-19
LUMBAR CONTROL SWITCH -
OPERATION.........................8N-19
LUMBAR CONTROL SWITCH - REMOVAL . 8N-19
LUMBAR MOTOR - DESCRIPTION.......8N-19
LUMBAR MOTOR - DIAGNOSIS AND
TESTING...........................8N-20
LUMBAR MOTOR - OPERATION.........8N-20
MAIN BEARING - FITTING - STANDARD
PROCEDURE, CRANKSHAFT.......9-133,9-202
MAIN BEARING CLEARANCE -
STANDARD PROCEDURE................9-322
MAIN BEARING FITTING - STANDARD
PROCEDURE, CRANKSHAFT............9-253
MAIN BEARING FITTING, STANDARD
PROCEDURE.........................9-43
MAIN BEARINGS - DESCRIPTION,
CRANKSHAFT.......................9-253
MAIN BEARINGS - INSPECTION,
CRANKSHAFT..................9-133,9-203
MAIN BEARINGS - INSTALLATION,
CRANKSHAFT..................9-254,9-383
MAIN BEARINGS - OPERATION,
CRANKSHAFT.......................9-253
MAIN BEARINGS - REMOVAL,
CRANKSHAFT..................9-254,9-383
MAIN BEARINGS - STANDARD
PROCEDURE, FITTING CRANKSHAFT.....9-383
MAINTENANCE SCHEDULES -
DESCRIPTION.........................0-6
MALFUNCTION INDICATOR LAMP (MIL) -
DESCRIPTION.......................8J-30
MALFUNCTION INDICATOR LAMP (MIL) -
OPERATION.........................8J-30
MANAGER - DESCRIPTION, TASK.........25-1
MANAGER - OPERATION, TASK..........25-5
MANIFOLD - CLEANING, EXHAUST . 9-161,9-220,
9-277,9-347,9-404
MANIFOLD - CLEANING, INTAKE . . . 9-158,9-219,
9-275,9-346,9-402
MANIFOLD - DESCRIPTION, EXHAUST . . . 9-159,
9-220,9-277,9-403,9-73
MANIFOLD - DESCRIPTION, INTAKE.....9-157,
9-219,9-274,9-401,9-71
MANIFOLD - INSPECTION, EXHAUST.....9-161,
9-220,9-277,9-347,9-404
MANIFOLD - INSPECTION, INTAKE . 9-158,9-219,
9-275,9-346,9-402
MANIFOLD - INSTALLATION, EXHAUST . . . 9-162,
9-220,9-277,9-347,9-404,9-74
MANIFOLD - INSTALLATION, INTAKE.....9-158,
9-219,9-275,9-346,9-402,9-72
MANIFOLD - OPERATION, EXHAUST.....9-220,
9-277,9-403
MANIFOLD - OPERATION, INTAKE........9-274
MANIFOLD - REMOVAL, EXHAUST . . 9-159,9-220,
9-277,9-347,9-404,9-73
MANIFOLD - REMOVAL, INTAKE . . . 9-157,9-219,
9-275,9-345,9-401,9-72
MANIFOLD LEAKAGE - DIAGNOSIS AND
TESTING, INTAKE
.....9-157,9-219,9-274,9-401
MANIFOLD LEAKS - DIAGNOSIS AND
TESTING, INTAKE
.....................9-71
MANUAL - INSTALLATION, WINDOW
REGULATOR
...................23-26,23-35
MANUAL - REMOVAL, WINDOW
REGULATOR
...................23-26,23-35
MANUAL BLEEDING - STANDARD
PROCEDURE
..........................5-5
20 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

RETURN - DESCRIPTION, SENSOR.......8E-10
RETURN HOSE - GEAR TO COOLER -
INSTALLATION..................19-43,19-44
RETURN HOSE - GEAR TO COOLER -
REMOVAL..........................19-43
RETURN HOSE - RESERVOIR TO
COOLER - INSTALLATION.........19-43,19-44
RETURN HOSE - RESERVOIR TO
COOLER - REMOVAL.............19-43,19-44
REVOLUTIONS PER MILE,
SPECIFICATIONS - TIRE...............22-10
RFE TRANSMISSION, SPECIAL TOOLS . . . 21-535
RIGHT - DESCRIPTION, CAMSHAFT(S)....9-117
RIGHT - INSTALLATION.................2-34
RIGHT - INSTALLATION, CAMSHAFT(S) . . . 9-118
RIGHT - INSTALLATION, CYLINDER
HEAD...............................9-32
RIGHT - REMOVAL....................2-34
RIGHT - REMOVAL, CAMSHAFT(S).......9-117
RIGHT - REMOVAL, CYLINDER HEAD......9-32
RIGHT CYLINDER HEAD - INSTALLATION . . 9-111
RIGHT CYLINDER HEAD - REMOVAL.....9-108
RIGHT OUTBOARD - INSTALLATION,
CENTER ANCHOR....................8O-45
RIGHT OUTBOARD - REMOVAL, CENTER
ANCHOR...........................8O-43
RIGHT REAR CABLE - INSTALLATION......5-32
RIGHT REAR CABLE - REMOVAL.........5-31
RIGHT SIDE - INSTALLATION...........9-121
RIGHT SIDE - REMOVAL...............9-121
RING - INSTALLATION, PINION
GEAR/RING GEAR/TONE......3-123,3-150,3-96
RING - REMOVAL, PINION GEAR/RING
GEAR/TONE................3-122,3-149,3-94
RING FITTING - STANDARD
PROCEDURE, PISTON . 9-140,9-207,9-262,9-333,
9-52
RINGS - STANDARD PROCEDURE,
FITTING PISTON.....................9-390
RKE TRANSMITTER BATTERIES -
STANDARD PROCEDURE...............8N-9
RKE TRANSMITTER CUSTOMER
PREFERENCES - STANDARD
PROCEDURE.........................8N-9
RKE TRANSMITTER PROGRAMING -
STANDARD PROCEDURE..............8N-10
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-3
ROAD TESTING - DIAGNOSIS AND
TESTING..............21-139,21-320,21-491
ROCKER ARM / ADJUSTER ASSEMBLY -
DESCRIPTION.......................9-124
ROCKER ARM / ADJUSTER ASSEMBLY -
INSTALLATION..................9-124,9-249
ROCKER ARM / ADJUSTER ASSEMBLY -
REMOVAL.....................9-124,9-249
ROCKER ARM / ADJUSTER ASSY -
CLEANING..........................9-310
ROCKER ARM / ADJUSTER ASSY -
DESCRIPTION.......................9-310
ROCKER ARM / ADJUSTER ASSY -
INSPECTION........................9-311
ROCKER ARM / ADJUSTER ASSY -
INSTALLATION.............9-198,9-312,9-379
ROCKER ARM / ADJUSTER ASSY -
REMOVAL................9-198,9-310,9-379
ROCKER ARM - DESCRIPTION
.......9-30,9-36
ROCKER ARM - INSTALLATION
..........9-30
ROCKER ARM - REMOVAL
..........9-30,9-36
ROCKER HOUSING - INSTALLATION
......9-304
ROCKER HOUSING - REMOVAL
.........9-304
ROD - CLEANING, PISTON &
CONNECTING
........9-138,9-206,9-261,9-389
ROD - CLEANING, PISTON AND
CONNECTING
........................9-331
ROD - DESCRIPTION, PISTON &
CONNECTING
. . . 9-137,9-205,9-260,9-329,9-388,
9-47
ROD - INSPECTION, CONNECTING
.......9-332
ROD - INSPECTION, PISTON &
CONNECTING
........9-138,9-206,9-261,9-389
ROD - INSTALLATION, PISTON &
CONNECTING
........9-139,9-207,9-261,9-389
ROD - REMOVAL, PISTON &
CONNECTING
. . . 9-137,9-205,9-261,9-330,9-389
ROD BEARING AND CRANKSHAFT
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING
............9-321ROD BEARING FITTING - STANDARD
PROCEDURE, CONNECTING . . 9-128,9-251,9-382
ROD BEARING FITTING, STANDARD
PROCEDURE - CONNECTING.............9-48
ROD END - DIAGNOSIS AND TESTING,
OUTER TIE..........................19-31
ROD END - INSTALLATION, OUTER TIE . . . 19-32
ROD END - INSTALLATION, TIE.........19-37
ROD END - REMOVAL, OUTER TIE.......19-31
ROD END - REMOVAL, TIE.............19-36
ROTATION - STANDARD PROCEDURE,
TIRE................................22-2
ROTOR - 5.9L V-8 - DIAGNOSIS AND
TESTING, DISTRIBUTOR...............8I-19
ROUTING, 5.7L V-8 ENGINE - FIRING
ORDER / CABLE.......................8I-4
RUN CHANNEL - INSTALLATION, GLASS . . 23-21,
23-31
RUN CHANNEL - REMOVAL, GLASS . 23-21,23-30
RUN WEATHERSTRIP - INSTALLATION,
FRONT DOOR GLASS.................23-92
RUN WEATHERSTRIP - INSTALLATION,
REAR DOOR GLASS..................23-93
RUN WEATHERSTRIP - REMOVAL,
FRONT DOOR GLASS.................23-92
RUN WEATHERSTRIP - REMOVAL, REAR
DOOR GLASS.......................23-93
RUNOUT - DIAGNOSIS AND TESTING,
TIRE AND WHEEL.....................22-1
RWAL VALVE - DESCRIPTION............5-44
RWAL VALVE - INSTALLATION...........5-45
RWAL VALVE - OPERATION.............5-44
RWAL VALVE - REMOVAL...............5-45
SAFETY CERTIFICATION LABEL -
DESCRIPTION, VEHICLE..............Intro.-1
SAFETY PRECAUTIONS AND WARNINGS,
WARNING...........................23-1
SAFETY PRECAUTIONS, STANDARD
PROCEDURE.........................8L-7
SAFETY PRECAUTIONS, WARNING -
WINDSHIELD........................23-88
SANDING/BUFFING & POLISHING -
DESCRIPTION, FINESSE...............23-75
SCHEDULES - DESCRIPTION,
MAINTENANCE........................0-6
SCHEMATICS AND DIAGRAMS -
HYDRAULIC SCHEMATICS . 21-175,21-355,21-513
SCHEMATICS, SCHEMATICS AND
DIAGRAMS - HYDRAULIC . 21-175,21-355,21-513
SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP-TO-FILLER NECK.........7-61
SEAL - FRONT - DESCRIPTION,
CRANKSHAFT OIL....................9-254
SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL . 9-134,9-203,9-255,9-324,9-45
SEAL - FRONT - OPERATION,
CRANKSHAFT OIL....................9-254
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL . 9-134,9-203,9-254,9-323,9-44
SEAL - FRONT COVER INSTALLED -
INSTALLATION, FRONT OIL.............9-384
SEAL - FRONT COVER INSTALLED -
REMOVAL, FRONT OIL................9-384
SEAL - FRONT COVER REMOVED -
INSTALLATION, FRONT OIL.............9-384
SEAL - FRONT COVER REMOVED -
REMOVAL, FRONT OIL................9-384
SEAL - INSTALLATION, ADAPTER
HOUSING...............21-127,21-539,21-83
SEAL - INSTALLATION, DOOR OPENING . . . 23-92
SEAL - INSTALLATION, EXTENSION
HOUSING.........21-127,21-200,21-380,21-83
SEAL - INSTALLATION, EXTENSION
HOUSING BUSHING............21-616,21-682
SEAL - INSTALLATION, FRONT OUTPUT
SHAFT..........21-618,21-653,21-683,21-717
SEAL - INSTALLATION, OIL PUMP
FRONT............................21-567
SEAL - INSTALLATION, PINION
....3-113,3-140,
3-35,3-60,3-85
SEAL - INSTALLATION, STEERING GEAR
INPUT SHAFT
.......................19-28
SEAL - INSTALLATION, VALVE STEM
.....9-378
SEAL - REAR - DESCRIPTION,
CRANKSHAFT OIL
....................9-255
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL
....9-136,9-204,9-256,9-325,
9-385,9-46SEAL - REAR - OPERATION,
CRANKSHAFT OIL....................9-255
SEAL - REAR - REMOVAL, CRANKSHAFT
OIL .......9-135,9-204,9-255,9-325,9-385,9-45
SEAL - REMOVAL, ADAPTER HOUSING . . 21-127,
21-539,21-83
SEAL - REMOVAL, DOOR OPENING......23-92
SEAL - REMOVAL, EXTENSION
HOUSING.........21-127,21-200,21-380,21-83
SEAL - REMOVAL, EXTENSION HOUSING
BUSHING....................21-616,21-682
SEAL - REMOVAL, FRONT OUTPUT
SHAFT..........21-617,21-653,21-683,21-717
SEAL - REMOVAL, OIL PUMP FRONT....21-567
SEAL - REMOVAL, PINION....3-113,3-140,3-34,
3-60,3-85
SEAL - REMOVAL, STEERING GEAR
INPUT SHAFT.......................19-25
SEAL AND DUST BOOT - INSTALLATION,
EXTENSION HOUSING..........21-652,21-716
SEAL AND DUST BOOT - REMOVAL,
EXTENSION HOUSING..........21-652,21-716
SEAL AREA LEAKS - DIAGNOSIS AND
TESTING, REAR.............9-135,9-204,9-64
SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL.....9-205,9-326,9-386
SEAL RETAINER - REMOVAL,
CRANKSHAFT REAR OIL.....9-204,9-326,9-386
SEALER LOCATIONS - SPECIFICATIONS . . 23-103
SEALERS - STANDARD PROCEDURE,
FORM-IN-PLACE GASKETS . . . 9-232,9-289,9-360,
9-9,9-93
SEALS - DESCRIPTION, VALVE GUIDE . . . 9-31,9-36
SEALS - DESCRIPTION, VALVE STEM....9-126,
9-198
SEALS - INSTALLATION, AXLE SHAFT . 3-33,3-58,
3-84
SEALS - REMOVAL, AXLE SHAFT . 3-33,3-58,3-84
SEALS - REMOVAL, VALVE SPRINGS.....9-308
SEALS - REMOVAL, VALVE STEM........9-377
SEAT - FRONT - INSTALLATION.........23-82
SEAT - FRONT - REMOVAL.............23-82
SEAT - INSTALLATION, CENTER.........23-77
SEAT - REAR - INSTALLATION..........23-84
SEAT - REAR - REMOVAL..............23-84
SEAT - REMOVAL, CENTER.............23-76
SEAT BACK - INSTALLATION, CENTER
ARMREST..........................23-78
SEAT BACK - REAR - INSTALLATION.....23-84
SEAT BACK - REAR - REMOVAL.........23-84
SEAT BACK - REMOVAL, CENTER
ARMREST..........................23-77
SEAT BACK CUSHION / COVER - FRONT
- INSTALLATION.....................23-83
SEAT BACK CUSHION / COVER - FRONT
- REMOVAL.........................23-83
SEAT BACK CUSHION / COVER - REAR -
INSTALLATION.......................23-85
SEAT BACK CUSHION / COVER - REAR -
REMOVAL..........................23-85
SEAT BACK HINGE - INSTALLATION,
CENTER............................23-80
SEAT BACK HINGE - REMOVAL, CENTER . . 23-79
SEAT BACK INERTIA HINGE COVER -
INSTALLATION, CENTER
...............23-78
SEAT BACK INERTIA HINGE COVER -
REMOVAL, CENTER
...................23-78
SEAT BACK LID - INSTALLATION,
CENTER
............................23-80
SEAT BACK LID - REMOVAL, CENTER
....23-80
SEAT BACK REAR - FOOTMANS LOOP
BRACKETS - INSTALLATION
............23-85
SEAT BACK REAR - FOOTMANS LOOP
BRACKETS - REMOVAL
................23-85
SEAT BELT - INSTALLATION, FRONT
CENTER
............................8O-27
SEAT BELT - REMOVAL, FRONT CENTER
. . 8O-26
SEAT BELT & RETRACTOR -
INSTALLATION, FRONT CENTER
.........8O-26
SEAT BELT & RETRACTOR -
INSTALLATION, REAR CENTER
..........8O-40
SEAT BELT & RETRACTOR -
INSTALLATION, REAR OUTBOARD
.......8O-42
SEAT BELT & RETRACTOR - REMOVAL,
FRONT CENTER
......................8O-25
SEAT BELT & RETRACTOR - REMOVAL,
REAR CENTER
.......................8O-39
DRINDEX 29
Description Group-Page Description Group-Page Description Group-Page