2003 DODGE RAM tow

During periods of high manifold vacuum, such as
idle or cruising speeds, vacuum is sufficient to com-
pletely compress spring. It will then pull the plunger
to the top of the valve (Fig. 17). In this position there
is minimal vapor flow through the valve.
During periods of moderate manifold vacuum, the
plunger is only pulled part way back from inlet. This
results in maximum vapor flow through the valve
(Fig. 18).
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - PCV VALVE - 3.7L
V-6/ 4.7L V-8
(1) Disconnect PCV line/hose (Fig. 19) by discon-
necting rubber connecting hose at PCV valve fitting.
(2) Remove PCV valve at oil filler tube by rotating
PCV valve downward until locating tabs have been
freed at cam lock (Fig. 19). After tabs have cleared,
pull valve straight out from filler tube.To prevent
damage to PCV valve locating tabs, valve must
be pointed downward for removal. Do not force
valve from oil filler tube.(3) After valve is removed, check condition of valve
o-ring (Fig. 19). Also, PCV valve should rattle when
shaken.
(4) Reconnect PCV valve to its connecting line/
hose.
(5) Start engine and bring to idle speed.
(6) If valve is not plugged, a hissing noise will be
heard as air passes through valve. Also, a strong vac-
uum should be felt with a finger placed at valve
inlet.
(7) If vacuum is not felt at valve inlet, check line/
hose for kinks or for obstruction. If necessary, clean
out intake manifold fitting at rear of manifold. Do
this by turning a 1/4 inch drill (by hand) through the
fitting to dislodge any solid particles. Blow out the
fitting with shop air. If necessary, use a smaller drill
to avoid removing any metal from the fitting.
(8)Do not attempt to clean the old PCV valve.
(9) Return PCV valve back to oil filler tube by
placing valve locating tabs (Fig. 19) into cam lock.
Press PCV valve in and rotate valve upward. A slight
click will be felt when tabs have engaged cam lock.
Valve should be pointed towards rear of vehicle.
(10) Connect PCV line/hose and connecting rubber
hose to PCV valve.
(11) Disconnect rubber hose from fresh air fitting
at air cleaner resonator box. Start engine and bring
to idle speed. Hold a piece of stiff paper (such as a
parts tag) loosely over the opening of the discon-
nected rubber hose.
(12) The paper should be drawn against the hose
opening with noticeable force. This will be after
allowing approximately one minute for crankcase
pressure to reduce.
(13) If vacuum is not present, disconnect each PCV
system hose at top of each crankcase breather (Fig.
20). Check for obstructions or restrictions.
(14) If vacuum is still not present, remove each
PCV system crankcase breather (Fig. 20) from each
cylinder head. Check for obstructions or restrictions.
If plugged, replace breather. Tighten breather to 12
N´m (106 in. lbs.) torque. Do not attempt to clean
breather.
(15) If vacuum is still not present, disconnect each
PCV system hose at each fitting, and at each check
valve (Fig. 21). Check for obstructions or restrictions.DIAGNOSIS AND TESTING - PCV VALVE - 5.9L
V-8
(1) With engine idling, remove the PCV valve from
cylinder head (valve) cover. If the valve is not
plugged, a hissing noise will be heard as air passes
through the valve. Also, a strong vacuum should be
felt at the valve inlet (Fig. 22).
(2) Return the PCV valve into the valve cover.
Remove the fitting and air hose at the opposite valve
Fig. 16 ENGINE OFF OR ENGINE BACKFIRE - NO
VAPOR FLOW
Fig. 17 HIGH INTAKE MANIFOLD VACUUM -
MINIMAL VAPOR FLOW
Fig. 18 MODERATE INTAKE MANIFOLD VACUUM -
MAXIMUM VAPOR FLOW
DREVAPORATIVE EMISSIONS 25 - 19
PCV VALVE (Continued)

tabs, valve must be pointed downward for
removal. Do not force valve from oil filler tube.
(3) After valve is removed, check condition of valve
o-ring (Fig. 25).
5.7L V-8
The PCV valve is mounted into the top of the
intake manifold, located to the right / rear of the
throttle body (Fig. 12). The PCV valve is sealed to
the intake manifold with 2 o-rings (Fig. 13).
(1) Remove PCV valve by rotating counter-clock-
wise 90 degrees until locating tabs have been freed.
After tabs have cleared, pull valve straight up from
intake manifold.
(2) After valve is removed, check condition of 2
valve o-rings.
INSTALLATION
3.7L V6 / 4.7L V-8
The PCV valve is located on the oil filler tube. Two
locating tabs are located on the side of the valve.
These 2 tabs fit into a cam lock in the oil filler tube.
An o-ring seals the valve to the filler tube.
(1) Return PCV valve back to oil filler tube by
placing valve locating tabs into cam lock. Press PCV
valve in and rotate valve upward. A slight click will
be felt when tabs have engaged cam lock. Valve
should be pointed towards rear of vehicle.
(2) Connect PCV line/hose and rubber hose to PCV
valve.
5.7L V-8
(1) Clean out intake manifold opening.
(2) Check condition of 2 o-rings on PCV valve.
(3) Apply engine oil to 2 o-rings.
(4) Place PCV valve into intake manifold and
rotate 90 degrees clockwise for installation.
VACUUM LINES
DESCRIPTION
A vacuum schematic for emission related items can
be found on the vehicles VECI label. Refer to Vehicle
Emission Control Information (VECI) Label for label
location.
VAPOR CANISTER
DESCRIPTION
Two, maintenance free, EVAP canisters are used.
Both canisters are mounted into a two-piece support
bracket located near the front of the fuel tank (Fig.
26).
OPERATION
Two, maintenance free, EVAP canisters are
used.The EVAP canisters are filled with granules of
an activated carbon mixture. Fuel vapors entering
the EVAP canisters are absorbed by the charcoal
granules.
Fuel tank pressure vents into the EVAP canisters.
Fuel vapors are temporarily held in the canisters
until they can be drawn into the intake manifold.
The duty cycle EVAP canister purge solenoid allows
the EVAP canisters to be purged at predetermined
times and at certain engine operating conditions.
REMOVAL
Two, maintenance free, EVAP canisters are used.
Both canisters are mounted into a two-piece support
bracket located near the front of the fuel tank (Fig.
26).
(1) Raise and support vehicle.
(2) Remove fuel tubes/lines at each EVAP canister.
Note location of tubes/lines before removal for easier
installation.
(3) Remove lower support bracket (Fig. 27).
(4) Remove mounting nuts at top of each canister
(Fig. 27).
Fig. 26 LOCATION, EVAP CANISTERS
1 - LDP
2 - LDP MOUNTING BOLT
3 - ELEC. CONNEC.
4 - FILTER MOUNTING BOLT
5 - LDP FILTER
6 - CONNECTING HOSE
7 - EVAP CANISTER MOUNTING BRACKET
8 - EVAP CANISTERS (2)
25 - 22 EVAPORATIVE EMISSIONSDR
PCV VALVE (Continued)

FLUID RESERVOIR - REMOVAL..........5-19
FLUID, SPECIFICATIONS - BRAKE.........5-18
FLUSH - SPECIFICATIONS, GAP.........23-95
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-17
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-39
FLYWHEEL - ASSEMBLY................6-12
FLYWHEEL - DIAGNOSIS AND TESTING....6-11
FLYWHEEL - DISASSEMBLY.............6-12
FLYWHEEL - INSTALLATION.............6-12
FLYWHEEL - REMOVAL.................6-12
FOG LAMP - INSTALLATION............8L-11
FOG LAMP - REMOVAL................8L-11
FOG LAMP RELAY - DESCRIPTION.......8L-11
FOG LAMP RELAY - DIAGNOSIS AND
TESTING, FRONT.....................8L-12
FOG LAMP RELAY - INSTALLATION......8L-13
FOG LAMP RELAY - OPERATION.........8L-12
FOG LAMP RELAY - REMOVAL..........8L-13
FOOTMANS LOOP BRACKETS -
INSTALLATION, SEAT BACK REAR.......23-85
FOOTMANS LOOP BRACKETS -
REMOVAL, SEAT BACK REAR...........23-85
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE.....9-232,
9-289,9-360,9-9,9-93
FRAME - INSTALLATION, GRILLE........23-40
FRAME - REAR - INSTALLATION, SEAT
CUSHION...........................23-85
FRAME - REAR - REMOVAL, SEAT
CUSHION...........................23-85
FRAME - REMOVAL, GRILLE............23-40
FRAME DIMENSIONS - SPECIFICATIONS . . 13-17
FRAME H-SECTION REPLACEMENT -
STANDARD PROCEDURE, REAR.........13-15
FRAME RAIL TIP REPLACEMENT -
STANDARD PROCEDURE, LIGHT DUTY
FRONT..............................13-4
FRONT - DESCRIPTION, CRANKSHAFT
OIL SEAL...........................9-254
FRONT - INSTALLATION........5-16,5-17,5-29
FRONT - INSTALLATION...............22-15
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL........9-134,9-203,9-255,9-324,9-45
FRONT - INSTALLATION, SEAT..........23-82
FRONT - INSTALLATION, SEAT BACK
CUSHION / COVER...................23-83
FRONT - INSTALLATION, SEAT CUSHION
/ COVER............................23-83
FRONT - OPERATION, CRANKSHAFT OIL
SEAL..............................9-254
FRONT - REMOVAL............5-12,5-16,5-28
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL...........9-134,9-203,9-254,9-323,9-44
FRONT - REMOVAL, SEAT..............23-82
FRONT - REMOVAL, SEAT BACK
CUSHION / COVER...................23-83
FRONT - REMOVAL, SEAT CUSHION /
COVER.............................23-83
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-2
FRONT AXLE - 9 1/4 AA -
ADJUSTMENTS.......................3-49
FRONT AXLE - 9 1/4 AA - DESCRIPTION . . . 3-45
FRONT AXLE - 9 1/4 AA - DIAGNOSIS
AND TESTING........................3-45
FRONT AXLE - 9 1/4 AA - INSTALLATION . . . 3-48
FRONT AXLE - 9 1/4 AA - OPERATION.....3-45
FRONT AXLE - 9 1/4 AA - REMOVAL......3-48
FRONT AXLE - 9 1/4 AA - SPECIAL
TOOLS..............................3-53
FRONT AXLE - 9 1/4 AA -
SPECIFICATIONS......................3-53
FRONT AXLE - C205F - ADJUSTMENTS....3-21
FRONT AXLE - C205F - DESCRIPTION.....3-18
FRONT AXLE - C205F - DIAGNOSIS AND
TESTING............................3-18
FRONT AXLE - C205F - INSTALLATION.....3-21
FRONT AXLE - C205F - OPERATION.......3-18
FRONT AXLE - C205F - REMOVAL
........3-21
FRONT AXLE - C205F - SPECIAL TOOLS
. . . 3-30
FRONT AXLE - C205F - SPECIFICATIONS
. . . 3-29
FRONT BEARING - INSTALLATION,
OUTPUT SHAFT
...............21-217,21-395
FRONT BEARING - REMOVAL, OUTPUT
SHAFT
......................21-217,21-395FRONT BRAKE HOSE - INSTALLATION......5-9
FRONT BUMPER - INSTALLATION.........13-2
FRONT BUMPER - REMOVAL............13-2
FRONT CENTER SEAT BELT -
INSTALLATION......................8O-27
FRONT CENTER SEAT BELT - REMOVAL . . 8O-26
FRONT CENTER SEAT BELT &
RETRACTOR - INSTALLATION...........8O-26
FRONT CENTER SEAT BELT &
RETRACTOR - REMOVAL..............8O-25
FRONT CLUTCH - ASSEMBLY....21-206,21-386
FRONT CLUTCH - DESCRIPTION . . 21-204,21-384
FRONT CLUTCH - DISASSEMBLY . 21-205,21-384
FRONT CLUTCH - INSPECTION . . . 21-206,21-385
FRONT CLUTCH - OPERATION . . . 21-204,21-384
FRONT CONTROL MODULE -
DESCRIPTION.....................8W-97-4
FRONT CONTROL MODULE -
DESCRIPTION........................8E-5
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING.....................8W-97-5
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING........................8E-6
FRONT CONTROL MODULE -
INSTALLATION....................8W-97-5
FRONT CONTROL MODULE -
INSTALLATION........................8E-6
FRONT CONTROL MODULE - OPERATION . 8W-97-5
FRONT CONTROL MODULE - OPERATION . . 8E-5
FRONT CONTROL MODULE - REMOVAL . . 8W-97-5
FRONT CONTROL MODULE - REMOVAL....8E-6
FRONT COVER INSTALLED -
INSTALLATION, FRONT OIL SEAL........9-384
FRONT COVER INSTALLED - REMOVAL,
FRONT OIL SEAL.....................9-384
FRONT COVER REMOVED -
INSTALLATION, FRONT OIL SEAL........9-384
FRONT COVER REMOVED - REMOVAL,
FRONT OIL SEAL.....................9-384
FRONT CROSSMEMBER - INSTALLATION . . 13-23
FRONT CROSSMEMBER - REMOVAL.....13-23
FRONT DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION........23-92
FRONT DOOR GLASS RUN
WEATHERSTRIP - REMOVAL............23-92
FRONT DOOR INNER BELT MOLDING -
INSTALLATION.......................23-93
FRONT DOOR INNER BELT MOLDING -
REMOVAL..........................23-93
FRONT DOOR OUTER BELT MOLDING -
INSTALLATION.......................23-93
FRONT DOOR OUTER BELT MOLDING -
REMOVAL..........................23-93
FRONT FASCIA - INSTALLATION..........13-3
FRONT FASCIA - REMOVAL..............13-3
FRONT FENDER - INSTALLATION........23-39
FRONT FENDER - REMOVAL............23-39
FRONT FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-12
FRONT FRAME RAIL TIP REPLACEMENT
- STANDARD PROCEDURE, LIGHT
DUTY...............................13-4
FRONT HOSE - REMOVAL
................5-9
FRONT MOUNT - INSTALLATION
. . . 9-144,9-211,
9-265,9-335,9-392,9-58
FRONT MOUNT - REMOVAL
. . 9-144,9-211,9-264,
9-335,9-392,9-57
FRONT OIL SEAL - FRONT COVER
INSTALLED - INSTALLATION
............9-384
FRONT OIL SEAL - FRONT COVER
INSTALLED - REMOVAL
...............9-384
FRONT OIL SEAL - FRONT COVER
REMOVED - INSTALLATION
.............9-384
FRONT OIL SEAL - FRONT COVER
REMOVED - REMOVAL
................9-384
FRONT OUTBOARD SEAT BELT BUCKLE -
INSTALLATION
......................8O-34
FRONT OUTBOARD SEAT BELT BUCKLE -
REMOVAL
..........................8O-33
FRONT OUTPUT SHAFT SEAL -
INSTALLATION
....21-618,21-653,21-683,21-717
FRONT OUTPUT SHAFT SEAL -
REMOVAL
.......21-617,21-653,21-683,21-717
FRONT PARKING BRAKE CABLE -
INSTALLATION
........................5-32
FRONT PARKING BRAKE CABLE -
REMOVAL
...........................5-31FRONT PROPELLER SHAFT -
INSTALLATION.........................3-7
FRONT PROPELLER SHAFT - REMOVAL.....3-6
FRONT SEAL - INSTALLATION, OIL
PUMP............................21-567
FRONT SEAL - REMOVAL, OIL PUMP....21-567
FRONT SERVO - ASSEMBLY.....21-209,21-388
FRONT SERVO - CLEANING.....21-208,21-388
FRONT SERVO - DESCRIPTION . . . 21-207,21-387
FRONT SERVO - DISASSEMBLY . . 21-208,21-388
FRONT SERVO - INSPECTION....21-208,21-388
FRONT SERVO - OPERATION....21-208,21-387
FRONT SKID PLATE - INSTALLATION.....13-24
FRONT SKID PLATE - REMOVAL.........13-24
FRONT SUSPENSION - DESCRIPTION,
GEAR - INDEPENDENT................19-16
FRONT SUSPENSION - INSTALLATION,
GEAR - INDEPENDENT................19-17
FRONT SUSPENSION - REMOVAL, GEAR
- INDEPENDENT.....................19-16
FRONT SUSPENSION, SPECIAL TOOLS....2-11
FRONT TOW HOOK ASSEMBLY -
INSTALLATION.......................13-26
FRONT TOW HOOK ASSEMBLY -
REMOVAL..........................13-26
FRONT WHEEL SPEED SENSOR -
DESCRIPTION........................5-41
FRONT WHEEL SPEED SENSOR -
INSTALLATION........................5-42
FRONT WHEEL SPEED SENSOR -
OPERATION..........................5-41
FRONT WHEEL SPEED SENSOR -
REMOVAL...........................5-41
FRONT WHEELHOUSE SPLASH SHIELD -
INSTALLATION.......................23-41
FRONT WHEELHOUSE SPLASH SHIELD -
REMOVAL..........................23-40
FUEL CONTROL ACTUATOR -
DESCRIPTION.......................14-85
FUEL CONTROL ACTUATOR -
INSTALLATION.......................14-85
FUEL CONTROL ACTUATOR -
OPERATION.........................14-85
FUEL CONTROL ACTUATOR - REMOVAL . . . 14-85
FUEL DELIVERY - GAS - DESCRIPTION....14-1
FUEL DELIVERY - GAS - OPERATION......14-2
FUEL DRAIN CIRCUIT - OPERATION......14-78
FUEL FILL DOOR - INSTALLATION.......23-39
FUEL FILL DOOR - REMOVAL...........23-39
FUEL FILLER CAP - DESCRIPTION.......25-13
FUEL FILLER CAP - OPERATION.........25-13
FUEL FILTER - STANDARD
PROCEDURES, WATER DRAINING AT.....14-57
FUEL FILTER / WATER SEPARATOR -
DESCRIPTION.......................14-61
FUEL FILTER / WATER SEPARATOR -
INSTALLATION.......................14-62
FUEL FILTER / WATER SEPARATOR -
OPERATION.........................14-61
FUEL FILTER / WATER SEPARATOR -
REMOVAL..........................14-61
FUEL FILTER/PRESSURE REGULATOR -
DESCRIPTION........................14-6
FUEL FILTER/PRESSURE REGULATOR -
OPERATION..........................14-6
FUEL GAUGE - DESCRIPTION...........8J-25
FUEL GAUGE - OPERATION.............8J-26
FUEL HEATER - DESCRIPTION..........14-63
FUEL HEATER - DIAGNOSIS AND
TESTING...........................14-63
FUEL HEATER - OPERATION............14-63
FUEL HEATER RELAY - DESCRIPTION....14-64
FUEL HEATER RELAY - INSTALLATION....14-64
FUEL HEATER RELAY - OPERATION......14-64
FUEL HEATER RELAY - REMOVAL........14-64
FUEL INDICATOR - DESCRIPTION, LOW . . . 8J-29
FUEL INDICATOR - OPERATION, LOW.....8J-29
FUEL INJECTION PUMP - DESCRIPTION . . 14-64
FUEL INJECTION PUMP - INSTALLATION . . 14-67
FUEL INJECTION PUMP - OPERATION....14-64
FUEL INJECTION PUMP - REMOVAL......14-65
FUEL INJECTION PUMP TIMING -
DIAGNOSIS AND TESTING.............14-65
FUEL INJECTOR - DESCRIPTION
....14-32,14-85
FUEL INJECTOR - INSTALLATION
........14-87
FUEL INJECTOR - OPERATION
.....14-32,14-86
FUEL INJECTOR - REMOVAL
............14-87
FUEL INJECTOR FIRING ORDER, DIESEL
. . 14-60
14 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-69
HINGE - INSTALLATION.....23-16,23-22,23-31,
23-46
HINGE - INSTALLATION, CENTER SEAT
BACK..............................23-80
HINGE - REMOVAL....23-16,23-22,23-31,23-46
HINGE - REMOVAL, CENTER SEAT BACK . . 23-79
HINGE COVER - INSTALLATION, CENTER
SEAT BACK INERTIA..................23-78
HINGE COVER - REMOVAL, CENTER
SEAT BACK INERTIA..................23-78
HITCH - INSTALLATION, TRAILER........13-25
HITCH - REMOVAL, TRAILER...........13-25
HOAT COOLANT - DESCRIPTION..........7-37
HOISTING - STANDARD PROCEDURE......0-14
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-14
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-14
HOLDDOWN - OPERATION, BATTERY.....8F-14
HOLDDOWN - REMOVAL, BATTERY......8F-14
HOLDER - INSTALLATION, CUP.........23-52
HOLDER - REMOVAL, CUP.............23-52
HOLDING CLUTCHES - DESCRIPTION....21-546
HOLDING CLUTCHES - OPERATION.....21-546
HOLE PLUG - INSTALLATION, CAMSHAFT
CORE..............................9-201
HOLE PLUG - REMOVAL, CAMSHAFT
CORE..............................9-200
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-9
HONING - STANDARD PROCEDURE,
CYLINDER BORE.......9-126,9-233,9-360,9-37
HOOD - INSTALLATION................23-47
HOOD - REMOVAL....................23-47
HOOK - INSTALLATION, COAT...........23-67
HOOK - REMOVAL, COAT..............23-67
HOOK ASSEMBLY - INSTALLATION,
FRONT TOW........................13-26
HOOK ASSEMBLY - REMOVAL, FRONT
TOW ..............................13-26
HORN - DIAGNOSIS AND TESTING.......8H-1
HORN - INSTALLATION.................8H-2
HORN - REMOVAL....................8H-2
HORN SWITCH - DESCRIPTION..........8H-2
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-2
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - GEAR TO COOLER -
INSTALLATION, RETURN..........19-43,19-44
HOSE - GEAR TO COOLER - REMOVAL,
RETURN............................19-43
HOSE - INSTALLATION, FRONT BRAKE......5-9
HOSE - INSTALLATION, PRESSURE . 19-43,19-44
HOSE - INSTALLATION, REAR BRAKE.......5-9
HOSE - REMOVAL, FRONT...............5-9
HOSE - REMOVAL, PRESSURE.....19-43,19-44
HOSE - REMOVAL, REAR BRAKE..........5-8
HOSE - RESERVOIR TO COOLER -
INSTALLATION, RETURN..........19-43,19-44
HOSE - RESERVOIR TO COOLER -
REMOVAL, RETURN.............19-43,19-44
HOSE ASSEMBLY - INSTALLATION, REAR
TUBE................................5-9
HOSE ASSEMBLY - REMOVAL, REAR
TUBE................................5-8
HOSE CLAMPS - DESCRIPTION...........7-3
HOSE CLAMPS - OPERATION.............7-5
HOSE WITH AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-70
HOSE WITH AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-68
HOSE WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-70
HOSE WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-69
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT..............24-33
HOSES/TUBES - DESCRIPTION, WASHER . 8R-11
HOSES/TUBES - OPERATION, WASHER . . . 8R-11
HOUSING - ASSEMBLY, HVAC
...........24-28
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH
..............................6-8
HOUSING - DISASSEMBLY, HVAC
........24-28
HOUSING - INSTALLATION, CLUTCH
......6-10
HOUSING - INSTALLATION, GEAR
........9-349HOUSING - INSTALLATION, HVAC........24-29
HOUSING - INSTALLATION, ROCKER.....9-304
HOUSING - REMOVAL, CLUTCH..........6-10
HOUSING - REMOVAL, GEAR...........9-348
HOUSING - REMOVAL, HVAC...........24-27
HOUSING - REMOVAL, ROCKER.........9-304
HOUSING BUSHING - INSTALLATION,
EXTENSION........................21-200
HOUSING BUSHING - REMOVAL,
EXTENSION........................21-200
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION.....21-616,21-682
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION.........21-616,21-682
HOUSING COVER - INSTALLATION, GEAR . 9-350
HOUSING COVER - REMOVAL, GEAR.....9-349
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER . . . 21-143,21-324,21-495
HOUSING SEAL - INSTALLATION,
ADAPTER...............21-127,21-539,21-83
HOUSING SEAL - INSTALLATION,
EXTENSION.......21-127,21-200,21-380,21-83
HOUSING SEAL - REMOVAL, ADAPTER . . 21-127,
21-539,21-83
HOUSING SEAL - REMOVAL,
EXTENSION.......21-127,21-200,21-380,21-83
HOUSING SEAL AND DUST BOOT -
INSTALLATION, EXTENSION.....21-652,21-716
HOUSING SEAL AND DUST BOOT -
REMOVAL, EXTENSION.........21-652,21-716
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
H-SECTION REPLACEMENT - STANDARD
PROCEDURE, REAR FRAME............13-15
HUB / BEARING - INSTALLATION.........2-31
HUB / BEARING - REMOVAL.............2-30
HVAC HOUSING - ASSEMBLY...........24-28
HVAC HOUSING - DISASSEMBLY........24-28
HVAC HOUSING - INSTALLATION........24-29
HVAC HOUSING - REMOVAL............24-27
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-25
HYDRAULIC LASH ADJUSTER -
DIAGNOSIS AND TESTING.........9-124,9-31
HYDRAULIC LIFTERS - CLEANING . . 9-260,9-388
HYDRAULIC LIFTERS - INSTALLATION . . . 9-260,
9-388
HYDRAULIC LIFTERS - REMOVAL . . . 9-259,9-387
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING......21-140,21-321,
21-493
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS........21-175,21-355,21-513
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING......................9-258,9-386
HYDROBOOST - INSTALLATION..........5-22
HYDROBOOST - INSTALLATION, ALL
EXCEPT.............................5-22
HYDROBOOST - REMOVAL..............5-21
HYDROBOOST - REMOVAL, ALL EXCEPT . . . 5-21
HYDRO-BOOST BRAKE BOOSTER -
INSTALLATION........................5-27
HYDRO-BOOST BRAKE BOOSTER -
REMOVAL...........................5-27
HYDROFORM FENDER RAIL REPAIR -
STANDARD PROCEDURE...............13-12
HYDROSTATIC LOCK - STANDARD
PROCEDURE.........9-186,9-232,9-290,9-361
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-6
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-6
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-2
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-33
IDLE AIR CONTROL MOTOR -
INSTALLATION.......................14-35
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-33
IDLE AIR CONTROL MOTOR - REMOVAL . . 14-34
IDLER SHAFT - INSTALLATION......9-175,9-80
IDLER SHAFT - REMOVAL
..........9-175,9-79
IGNITION - SPECIFICATIONS, TORQUE
.....8I-3
IGNITION CIRCUIT SENSE -
DESCRIPTION
.......................8E-10
IGNITION CIRCUIT SENSE - OPERATION
. . 8E-12
IGNITION COIL - DESCRIPTION
..........8I-19IGNITION COIL - INSTALLATION.........8I-24
IGNITION COIL - OPERATION............8I-20
IGNITION COIL - REMOVAL.............8I-23
IGNITION COIL CAPACITOR -
DESCRIPTION........................8I-33
IGNITION COIL CAPACITOR -
INSTALLATION.......................8I-33
IGNITION COIL CAPACITOR - OPERATION . . 8I-33
IGNITION COIL CAPACITOR - REMOVAL . . . 8I-33
IGNITION COIL RESISTANCE, 3.7L V-6.....8I-6
IGNITION COIL RESISTANCE, 4.7L V-8.....8I-6
IGNITION COIL RESISTANCE, 5.7L V-8.....8I-6
IGNITION COIL RESISTANCE, 5.9L.........8I-6
IGNITION COIL RESISTANCE, 8.0L V-10
ENGINE..............................8I-6
IGNITION CONTROL - DESCRIPTION.......8I-1
IGNITION SWITCH - DESCRIPTION........19-9
IGNITION SWITCH - DESCRIPTION,
KEY-IN.............................19-11
IGNITION SWITCH - DIAGNOSIS AND
TESTING............................19-9
IGNITION SWITCH - INSTALLATION......19-11
IGNITION SWITCH - OPERATION.........19-9
IGNITION SWITCH - REMOVAL..........19-10
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING . . . 19-11
IGNITION TIMING, SPECIFICATIONS.......8I-6
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE..........................8F-11
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY........................8E-15
IMMOBILIZER SYSTEM INDICATOR
LAMP - DESCRIPTION, SENTRY KEY......8Q-5
IMMOBILIZER SYSTEM INDICATOR
LAMP - OPERATION, SENTRY KEY........8Q-5
IMMOBILIZER SYSTEM INITIALIZATION,
STANDARD PROCEDURE - SENTRY
KEY................................8Q-3
IMMOBILIZER SYSTEM (SKIS),
DESCRIPTION - SENTRY KEY............8Q-1
IMMOBILIZER SYSTEM TRANSPONDER
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY.............8Q-4
IMPACT AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE..................8O-53
IMPACT AIRBAG CONTROL MODULE -
OPERATION, SIDE....................8O-54
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF.....21-201,21-381,
21-541
INDEPENDENT FRONT SUSPENSION -
DESCRIPTION, GEAR..................19-16
INDEPENDENT FRONT SUSPENSION -
INSTALLATION, GEAR.................19-17
INDEPENDENT FRONT SUSPENSION -
REMOVAL, GEAR.....................19-16
INDICATOR - DESCRIPTION, ABS........8J-17
INDICATOR - DESCRIPTION, AIRBAG.....8J-18
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-18
INDICATOR - DESCRIPTION, CARGO
LAMP..............................8J-20
INDICATOR - DESCRIPTION, CHECK
GAUGES............................8J-21
INDICATOR - DESCRIPTION, CRUISE.....8J-22
INDICATOR - DESCRIPTION, DOOR AJAR . . 8J-23
INDICATOR - DESCRIPTION, ETC........8J-24
INDICATOR - DESCRIPTION, GEAR
SELECTOR..........................8J-26
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-27
INDICATOR - DESCRIPTION, LAMP OUT . . . 8J-28
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-29
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-33
INDICATOR - DESCRIPTION, SEATBELT
. . . 8J-34
INDICATOR - DESCRIPTION, SECURITY
. . . 8J-34
INDICATOR - DESCRIPTION, SERVICE
4WD
...............................8J-35
INDICATOR - DESCRIPTION, TRANS
TEMP
..............................8J-38
INDICATOR - DESCRIPTION, TURN
SIGNAL
............................8J-39
DRINDEX 17
Description Group-Page Description Group-Page Description Group-Page

TIRE REVOLUTIONS PER MILE,
SPECIFICATIONS.....................22-10
TIRE ROTATION - STANDARD
PROCEDURE.........................22-2
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-8
TIRES - DESCRIPTION.................22-5
TIRES - DESCRIPTION, RADIAL - PLY.....22-6
TIRES - DESCRIPTION, REPLACEMENT....22-6
TIRE/VEHICLE LEAD - DIAGNOSIS AND
TESTING............................22-8
TO COOLER - INSTALLATION, RETURN
HOSE - GEAR..................19-43,19-44
TO COOLER - INSTALLATION, RETURN
HOSE - RESERVOIR.............19-43,19-44
TO COOLER - REMOVAL, RETURN HOSE
- GEAR............................19-43
TO COOLER - REMOVAL, RETURN HOSE
- RESERVOIR..................19-43,19-44
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-9
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . 8W-01-10
TO OIL COOLER - INSTALLATION, AIR.....7-75
TO OIL COOLER - REMOVAL, AIR.........7-74
TO OIL COOLER - REMOVAL, WATER......7-74
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TOE ADJUSTMENT - STANDARD
PROCEDURE..........................2-4
TOE ADJUSTMENT - STANDARD
PROCEDURE, CAMBER, CASTER..........2-4
TOOL - ADJUSTMENT, WITH ADJUSTING . . . 5-36
TOOLS - 4.7L ENGINE, SPECIAL.........9-102
TOOLS - 5.7L ENGINE, SPECIAL.........9-192
TOOLS - 5.9L DIESEL ENGINE, SPECIAL . . 9-294
TOOLS - 5.9L ENGINE, SPECIAL.........9-240
TOOLS - 8.0L ENGINE, SPECIAL.........9-367
TOOLS - 9 1/4 AA, SPECIAL.............2-29
TOOLS - BASE BRAKES, SPECIAL.........5-5
TOOLS - BATTERY SYSTEM SPECIAL
TOOLS, SPECIAL......................8F-7
TOOLS - BODY, SPECIAL...............23-14
TOOLS - COOLING, SPECIAL.............7-20
TOOLS - DIESEL FUEL SYSTEM,
SPECIAL...........................14-60
TOOLS - FRONT SUSPENSION, SPECIAL . . . 2-11
TOOLS - FUEL SYSTEM, SPECIAL........14-5
TOOLS - OVERHEAD CONSOLE, SPECIAL . . 8M-6
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL...........................19-22
TOOLS - RE TRANSMISSION, SPECIAL . . 21-189,
21-370
TOOLS - RFE TRANSMISSION, SPECIAL . . 21-535
TOOLS - STEERING LINKAGE, SPECIAL . . . 19-35
TOOLS - STEERING, SPECIAL............19-5
TOOLS - TRANSFER CASE NV271/NV273,
SPECIAL....................21-650,21-714
TOOLS - WHEEL ALIGNMENT, SPECIAL.....2-7
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, DIAGNOSIS AND TESTING -
SPECIAL............................11-4
TOOLS, FRONT AXLE - 9 1/4 AA -
SPECIAL............................3-53
TOOLS, FRONT AXLE - C205F - SPECIAL . . . 3-30
TOOLS, HALF SHAFT - SPECIAL..........3-12
TOOLS, HEADLAMP ALIGNMENT -
SPECIAL............................8L-7
TOOLS, MANUAL TRANSMISSION -
NV3500 - SPECIAL...................21-40
TOOLS, MANUAL TRANSMISSION -
NV4500 - SPECIAL...................21-79
TOOLS, MANUAL TRANSMISSION -
NV5600 - SPECIAL..................21-122
TOOLS, PROPELLER SHAFT - SPECIAL.....3-6
TOOLS, REAR AXLE - 10 1/2 AA -
SPECIAL...........................3-108
TOOLS, REAR AXLE - 11 1/2 AA -
SPECIAL
...........................3-135
TOOLS, REAR AXLE - 9 1/4 - SPECIAL
.....3-80
TOOLS, SPECIAL TOOLS - BATTERY
SYSTEM SPECIAL
.....................8F-7
TOOLS, SPECIFICATIONS - SPECIAL
.......9-16
TOP COVER - INSTALLATION,
INSTRUMENT PANEL
..................23-60TOP COVER - REMOVAL, INSTRUMENT
PANEL.............................23-59
TORSION BAR - DESCRIPTION...........2-25
TORSION BAR - INSTALLATION..........2-26
TORSION BAR - OPERATION.............2-25
TORSION BAR - REMOVAL..............2-25
TORSION BAR CROSS MEMBER
BUSHING - INSTALLATION..............2-14
TORSION BAR CROSSMEMBER
BUSHING - REMOVAL..................2-12
TOUCH-UP - DESCRIPTION, PAINT.......23-75
TOUCH-UP - STANDARD PROCEDURE,
PAINT.............................23-75
TOW HOOK ASSEMBLY - INSTALLATION,
FRONT.............................13-26
TOW HOOK ASSEMBLY - REMOVAL,
FRONT.............................13-26
TOW WIRING - DESCRIPTION, TRAILER . . 8L-22
TOWING - STANDARD PROCEDURE.......0-15
TRACK - DESCRIPTION, POWER SEAT....8N-18
TRACK - DIAGNOSIS AND TESTING,
POWER SEAT.......................8N-18
TRACK - INSTALLATION, POWER SEAT . . . 8N-19
TRACK - INSTALLATION, SEAT..........23-83
TRACK - OPERATION, POWER SEAT.....8N-18
TRACK - REMOVAL, POWER SEAT.......8N-19
TRACK - REMOVAL, SEAT..............23-83
TRACK BAR - INSTALLATION...........19-37
TRACK BAR - REMOVAL................19-37
TRAC-RITE - ASSEMBLY, DIFFERENTIAL . . 3-120,
3-147
TRAC-RITE - CLEANING, DIFFERENTIAL . . 3-119,
3-146
TRAC-RITE - DESCRIPTION,
DIFFERENTIAL..................3-118,3-145
TRAC-RITE - DISASSEMBLY,
DIFFERENTIAL..................3-118,3-145
TRAC-RITE - INSPECTION, DIFFERENTIAL . 3-119,
3-146
TRAC-RITE - OPERATION, DIFFERENTIAL . 3-118,
3-145
TRAILER HITCH - INSTALLATION........13-25
TRAILER HITCH - REMOVAL............13-25
TRAILER TOW WIRING - DESCRIPTION . . . 8L-22
TRANS COOLER - 5.9L DIESEL -
DESCRIPTION........................7-73
TRANS COOLER - 5.9L DIESEL -
OPERATION..........................7-74
TRANS TEMP INDICATOR -
DESCRIPTION.......................8J-38
TRANS TEMP INDICATOR - OPERATION . . . 8J-38
TRANSDUCER - DESCRIPTION, A/C
PRESSURE.........................24-15
TRANSDUCER - DIAGNOSIS AND
TESTING, A/C PRESSURE..............24-15
TRANSDUCER - INSTALLATION, A/C
PRESSURE.........................24-16
TRANSDUCER - OPERATION, A/C
PRESSURE.........................24-15
TRANSDUCER - REMOVAL, A/C
PRESSURE.........................24-16
TRANSFER CASE - NV241 GENII -
ASSEMBLY.........................21-604
TRANSFER CASE - NV241 GENII -
CLEANING
.........................21-602
TRANSFER CASE - NV241 GENII -
DESCRIPTION
.........................0-4
TRANSFER CASE - NV241 GENII -
DESCRIPTION
......................21-591
TRANSFER CASE - NV241 GENII -
DIAGNOSIS AND TESTING
............21-592
TRANSFER CASE - NV241 GENII -
DISASSEMBLY
......................21-593
TRANSFER CASE - NV241 GENII -
INSPECTION
.......................21-602
TRANSFER CASE - NV241 GENII -
INSTALLATION
......................21-614
TRANSFER CASE - NV241 GENII -
OPERATION
........................21-591
TRANSFER CASE - NV241 GENII -
REMOVAL
.........................21-593
TRANSFER CASE - NV243 - ASSEMBLY
. . 21-670
TRANSFER CASE - NV243 - CLEANING
. . 21-668
TRANSFER CASE - NV243 -
DESCRIPTION
.........................0-4
TRANSFER CASE - NV243 -
DESCRIPTION
......................21-658TRANSFER CASE - NV243 - DIAGNOSIS
AND TESTING......................21-659
TRANSFER CASE - NV243 -
DISASSEMBLY......................21-660
TRANSFER CASE - NV243 - INSPECTION . 21-668
TRANSFER CASE - NV243 -
INSTALLATION......................21-679
TRANSFER CASE - NV243 - OPERATION . 21-659
TRANSFER CASE - NV243 - REMOVAL . . . 21-660
TRANSFER CASE - NV271 - ASSEMBLY . . 21-637
TRANSFER CASE - NV271 - CLEANING . . 21-635
TRANSFER CASE - NV271 -
DESCRIPTION.........................0-4
TRANSFER CASE - NV271 -
DESCRIPTION......................21-623
TRANSFER CASE - NV271 - DIAGNOSIS
AND TESTING......................21-624
TRANSFER CASE - NV271 -
DISASSEMBLY......................21-625
TRANSFER CASE - NV271 - INSPECTION . 21-635
TRANSFER CASE - NV271 -
INSTALLATION......................21-649
TRANSFER CASE - NV271 - OPERATION . 21-623
TRANSFER CASE - NV271 - REMOVAL . . . 21-625
TRANSFER CASE - NV273 - ASSEMBLY . . 21-701
TRANSFER CASE - NV273 - CLEANING . . 21-698
TRANSFER CASE - NV273 -
DESCRIPTION.........................0-4
TRANSFER CASE - NV273 -
DESCRIPTION......................21-687
TRANSFER CASE - NV273 - DIAGNOSIS
AND TESTING......................21-688
TRANSFER CASE - NV273 -
DISASSEMBLY......................21-689
TRANSFER CASE - NV273 - INSPECTION . 21-699
TRANSFER CASE - NV273 -
INSTALLATION......................21-713
TRANSFER CASE - NV273 - OPERATION . 21-688
TRANSFER CASE - NV273 - REMOVAL . . . 21-689
TRANSFER CASE CONTROL MODULE -
DESCRIPTION.......................8E-15
TRANSFER CASE CONTROL MODULE -
OPERATION.........................8E-15
TRANSFER CASE, NV241 GENII........21-614
TRANSFER CASE, NV241/NV243 . . 21-615,21-680
TRANSFER CASE, NV243.............21-680
TRANSFER CASE, NV271.............21-649
TRANSFER CASE NV271/NV273, SPECIAL
TOOLS......................21-650,21-714
TRANSFER CASE, NV273.............21-713
TRANSFER CASE SKID PLATE -
INSTALLATION.......................13-26
TRANSFER CASE SKID PLATE -
REMOVAL..........................13-26
TRANSFER PUMP - DESCRIPTION, FUEL . . 14-75
TRANSFER PUMP - INSTALLATION, FUEL . 14-76
TRANSFER PUMP - OPERATION, FUEL....14-76
TRANSFER PUMP - REMOVAL, FUEL.....14-76
TRANSMISSION - 45RFE/545RFE -
DESCRIPTION, AUTOMATIC............21-489
TRANSMISSION - 45RFE/545RFE -
OPERATION, AUTOMATIC.............21-490
TRANSMISSION - 46RE - DESCRIPTION,
AUTOMATIC
........................21-131
TRANSMISSION - 46RE - OPERATION,
AUTOMATIC
........................21-133
TRANSMISSION - 48RE - DESCRIPTION,
AUTOMATIC
........................21-312
TRANSMISSION - 48RE - OPERATION,
AUTOMATIC
........................21-314
TRANSMISSION - CLEANING
..........21-104
TRANSMISSION - DESCRIPTION,
MANUAL
.............................0-4
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC
....21-139,21-320,21-491
TRANSMISSION - NV3500 - ASSEMBLY,
MANUAL
...........................21-17
TRANSMISSION - NV3500 - CLEANING,
MANUAL
...........................21-15
TRANSMISSION - NV3500 -
DESCRIPTION, MANUAL
................21-1
TRANSMISSION - NV3500 - DIAGNOSIS
AND TESTING, MANUAL
................21-3
TRANSMISSION - NV3500 -
DISASSEMBLY, MANUAL
................21-4
TRANSMISSION - NV3500 -
INSPECTION, MANUAL
................21-15
DRINDEX 35
Description Group-Page Description Group-Page Description Group-Page

VOLUME CHECK - STANDARD
PROCEDURE, OIL PUMP..............21-563
WAIT-TO-START INDICATOR -
DESCRIPTION.......................8J-42
WAIT-TO-START INDICATOR -
OPERATION.........................8J-42
WARNING - INSTALLATION.............23-88
WARNING - REMOVAL................23-88
WARNING - SAFETY PRECAUTIONS AND
WARNINGS..........................23-1
WARNING - SERVICE WARNINGS........24-32
WARNING - WINDSHIELD SAFETY
PRECAUTIONS.......................23-88
WARNING, CLUTCH.....................6-2
WARNINGS, GENERAL..............8W-01-7
WARNINGS, RESTRAINT SYSTEM........8O-5
WARNINGS, WARNING - SAFETY
PRECAUTIONS........................23-1
WARNINGS, WARNING - SERVICE.......24-32
WASHER FLUID INDICATOR -
DESCRIPTION.......................8J-42
WASHER FLUID INDICATOR -
OPERATION.........................8J-42
WASHER FLUID LEVEL SWITCH -
DESCRIPTION........................8R-9
WASHER FLUID LEVEL SWITCH -
INSTALLATION......................8R-11
WASHER FLUID LEVEL SWITCH -
OPERATION..........................8R-9
WASHER FLUID LEVEL SWITCH -
REMOVAL..........................8R-10
WASHER HOSES/TUBES - DESCRIPTION . . 8R-11
WASHER HOSES/TUBES - OPERATION....8R-11
WASHER NOZZLE - DESCRIPTION.......8R-12
WASHER NOZZLE - INSTALLATION......8R-12
WASHER NOZZLE - OPERATION.........8R-12
WASHER NOZZLE - REMOVAL..........8R-12
WASHER PUMP/MOTOR - DESCRIPTION . . 8R-13
WASHER PUMP/MOTOR - INSTALLATION . 8R-14
WASHER PUMP/MOTOR - OPERATION . . . 8R-13
WASHER PUMP/MOTOR - REMOVAL.....8R-14
WASHER RESERVOIR - DESCRIPTION....8R-15
WASHER RESERVOIR - OPERATION......8R-15
WASHER SYSTEM - CLEANING, WIPER....8R-6
WASHER SYSTEM - DIAGNOSIS AND
TESTING, WIPER.....................8R-6
WASHER SYSTEM - INSPECTION, WIPER . . 8R-7
WATER DRAINING AT FUEL FILTER -
STANDARD PROCEDURES..............14-57
WATER IN FUEL SENSOR -
DESCRIPTION.......................14-77
WATER IN FUEL SENSOR - OPERATION . . . 14-78
WATER IN FUEL SENSOR - REMOVAL....14-78
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-1
WATER PUMP - 5.7L - INSTALLATION.....7-71
WATER PUMP - 5.7L - REMOVAL.........7-70
WATER PUMP - 5.9L - CLEANING........7-64
WATER PUMP - 5.9L - DESCRIPTION......7-62
WATER PUMP - 5.9L - INSPECTION.......7-64
WATER PUMP - 5.9L - INSTALLATION.....7-64
WATER PUMP - 5.9L - OPERATION.......7-62
WATER PUMP - 5.9L - REMOVAL.........7-63
WATER PUMP - 5.9L DIESEL -
CLEANING...........................7-67
WATER PUMP - 5.9L DIESEL -
DESCRIPTION........................7-67
WATER PUMP - 5.9L DIESEL -
INSPECTION.........................7-68
WATER PUMP - 5.9L DIESEL -
INSTALLATION........................7-68
WATER PUMP - 5.9L DIESEL -
OPERATION
..........................7-67
WATER PUMP - 5.9L DIESEL - REMOVAL
. . 7-67
WATER PUMP - DESCRIPTION
...........7-64
WATER PUMP - DIAGNOSIS AND
TESTING
........................7-62,7-67
WATER PUMP - OPERATION
.............7-64
WATER PUMP BYPASS - DESCRIPTION
....7-64
WATER PUMP BYPASS - OPERATION
......7-65
WATER PUMP BYPASS HOSE WITH AIR
CONDITIONING - INSTALLATION
..........7-70WATER PUMP BYPASS HOSE WITH AIR
CONDITIONING - REMOVAL.............7-68
WATER PUMP BYPASS HOSE WITHOUT
AIR CONDITIONING - INSTALLATION......7-70
WATER PUMP BYPASS HOSE WITHOUT
AIR CONDITIONING - REMOVAL..........7-69
WATER SEPARATOR - DESCRIPTION,
FUEL FILTER........................14-61
WATER SEPARATOR - INSTALLATION,
FUEL FILTER........................14-62
WATER SEPARATOR - OPERATION, FUEL
FILTER.............................14-61
WATER SEPARATOR - REMOVAL, FUEL
FILTER.............................14-61
WATER TO OIL COOLER - REMOVAL......7-74
WATERDAM - INSTALLATION......23-25,23-34
WATERDAM - REMOVAL..........23-25,23-34
WATER-IN-FUEL INDICATOR -
DESCRIPTION.......................8J-43
WATER-IN-FUEL INDICATOR -
OPERATION.........................8J-43
WEAR - STANDARD PROCEDURE,
MEASURING TIMING CHAIN............9-165
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD......................22-7
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE.......................22-8
WEAR, STANDARD PROCEDURE -
MEASURING TIMING CHAIN.............9-76
WEATHERSTRIP - INSTALLATION, DRIP
RAIL..............................23-91
WEATHERSTRIP - INSTALLATION, FRONT
DOOR GLASS RUN.....................23-92
WEATHERSTRIP - INSTALLATION, REAR
DOOR GLASS RUN...................23-93
WEATHERSTRIP - REMOVAL, DRIP RAIL . . 23-91
WEATHERSTRIP - REMOVAL, FRONT
DOOR GLASS RUN...................23-92
WEATHERSTRIP - REMOVAL, REAR
DOOR GLASS RUN...................23-93
WEATHERSTRIP RETAINER -
INSTALLATION, A-PILLAR..............23-91
WEATHERSTRIP RETAINER -
INSTALLATION, DRIP RAIL.............23-92
WEATHERSTRIP RETAINER - REMOVAL,
A-PILLAR...........................23-91
WEATHERSTRIP RETAINER - REMOVAL,
DRIP RAIL..........................23-92
WELD LOCATIONS - SPECIFICATIONS . . . 23-122
WHEEL - INSTALLATION, STEERING......19-15
WHEEL - REMOVAL, STEERING.........19-15
WHEEL ALIGNMENT - DESCRIPTION.......2-1
WHEEL ALIGNMENT - OPERATION.........2-2
WHEEL ALIGNMENT, SPECIAL TOOLS......2-7
WHEEL ANTILOCK - DIAGNOSIS AND
TESTING, REAR.......................5-42
WHEEL BALANCE - STANDARD
PROCEDURE, TIRE....................22-4
WHEEL COVER - REMOVAL............22-14
WHEEL INSPECTION, DIAGNOSIS AND
TESTING...........................22-11
WHEEL INSTALLATION - STANDARD
PROCEDURE, DUAL REAR.............22-12
WHEEL REPLACEMENT - STANDARD
PROCEDURE........................22-12
WHEEL RUNOUT - DIAGNOSIS AND
TESTING, TIRE.......................22-1
WHEEL SPEED SENSOR - DESCRIPTION,
FRONT..............................5-41
WHEEL SPEED SENSOR - DIAGNOSIS
AND TESTING, REAR...................5-43
WHEEL SPEED SENSOR -
INSTALLATION, FRONT.................5-42
WHEEL SPEED SENSOR -
INSTALLATION, REAR..................5-43
WHEEL SPEED SENSOR - OPERATION,
FRONT..............................5-41
WHEEL SPEED SENSOR - REMOVAL,
FRONT..............................5-41
WHEEL SPEED SENSOR - REMOVAL,
REAR...............................5-42
WHEEL WITH MATCHING TIRE -
DESCRIPTION, FULL SIZE, SPARE.......22-15WHEELHOUSE SPLASH SHIELD -
INSTALLATION, FRONT................23-41
WHEELHOUSE SPLASH SHIELD -
INSTALLATION, REAR.................23-41
WHEELHOUSE SPLASH SHIELD -
REMOVAL, FRONT....................23-40
WHEELHOUSE SPLASH SHIELD -
REMOVAL, REAR.....................23-41
WHEELS - DESCRIPTION..............22-11
WHEELS - OPERATION................22-11
WIND NOISE - DIAGNOSIS AND TESTING . . 23-2
WINDOW MOTOR - REMOVAL..........8N-22
WINDOW REGULATOR - MANUAL -
INSTALLATION..................23-26,23-35
WINDOW REGULATOR - MANUAL -
REMOVAL.....................23-26,23-35
WINDOW REGULATOR - POWER -
INSTALLATION..................23-25,23-34
WINDOW REGULATOR - POWER -
REMOVAL.....................23-25,23-34
WINDOW SWITCH - DIAGNOSIS AND
TESTING...........................8N-22
WINDOW SWITCH - INSTALLATION......8N-23
WINDOW SWITCH - REMOVAL..........8N-23
WINDOWS - DESCRIPTION, POWER.....8N-21
WINDOWS - DIAGNOSIS AND TESTING,
POWER............................8N-21
WINDOWS - OPERATION, POWER.......8N-21
WINDSHIELD SAFETY PRECAUTIONS,
WARNING..........................23-88
WIPER & WASHER SYSTEM - CLEANING....8R-6
WIPER & WASHER SYSTEM -
DIAGNOSIS AND TESTING..............8R-6
WIPER & WASHER SYSTEM -
INSPECTION.........................8R-7
WIPER ARM - DESCRIPTION...........8R-18
WIPER ARM - INSTALLATION...........8R-19
WIPER ARM - OPERATION.............8R-18
WIPER ARM - REMOVAL..............8R-18
WIPER BLADE - DESCRIPTION..........8R-19
WIPER BLADE - INSTALLATION.........8R-20
WIPER BLADE - OPERATION...........8R-19
WIPER BLADE - REMOVAL.............8R-19
WIPER HIGH/LOW RELAY -
DESCRIPTION.......................8R-20
WIPER HIGH/LOW RELAY - DIAGNOSIS
AND TESTING.......................8R-21
WIPER HIGH/LOW RELAY -
INSTALLATION......................8R-21
WIPER HIGH/LOW RELAY - OPERATION . . 8R-20
WIPER HIGH/LOW RELAY - REMOVAL....8R-21
WIPER MODULE - DESCRIPTION........8R-22
WIPER MODULE - INSTALLATION.......8R-23
WIPER MODULE - OPERATION..........8R-23
WIPER MODULE - REMOVAL...........8R-23
WIPER ON/OFF RELAY - DESCRIPTION . . . 8R-25
WIPER ON/OFF RELAY - DIAGNOSIS AND
TESTING...........................8R-26
WIPER ON/OFF RELAY - INSTALLATION . . . 8R-26
WIPER ON/OFF RELAY - OPERATION.....8R-25
WIPER ON/OFF RELAY - REMOVAL......8R-26
WIPERS/WASHERS - DESCRIPTION.......8R-1
WIPERS/WASHERS - OPERATION........8R-4
WIRE SPLICING - STANDARD
PROCEDURE
.....................8W-01-15
WIRING - DESCRIPTION, TRAILER TOW
. . 8L-22
WIRING DIAGRAMS - DESCRIPTION,
HOW TO USE
.....................8W-01-1
WIRING HARNESS - DIAGNOSIS AND
TESTING
.........................8W-01-7
WIRING/TERMINAL, SPECIAL TOOLS
. . 8W-01-10
WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS
HOSE
...............................7-70
WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS
HOSE
...............................7-69
WORN THREADS - STANDARD
PROCEDURE,
REPAIR DAMAGED OR
......9-186,9-232,9-289,
9-361,9-9,9-93
38 INDEXDR
Description Group-Page Description Group-Page Description Group-Page