2003 DAEWOO MATIZ battery

1A – 2 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
DESCRIPTION AND SYSTEMOPERATION
CLEANLINESS AND CARE
An automobile engine is a combination of many ma-
chined, honed, polished and lapped surfaces with toler-
ances that are measured in the ten–thousandths of an
inch. When any internal engine parts are serviced, care
and cleanliness are important. A liberal coating of en-
gine oil should be applied to friction areas during assem-
bly, to protect and lubricate the surfaces on initial
operation. Proper cleaning and protection of machined
surfaces and friction areas is part of the repair proce-
dure. This is considered standard shop practice even if
not specifically stated.
Whenever valve train components are removed for ser-
vice, they should be kept in order. They should be
installed in the same locations, and with the same mat-
ing surfaces, as when they were removed. Battery
cables should be disconnected before any major work is
performed on the engine. Failure to disconnect cablesmay result in damage to wire harness or other electrical
parts.
ON-ENGINE SERVICE
Caution: Disconnect the negative battery cable be-
fore removing or installing any electrical unit, or
when a tool or equipment could easily come in con-
tact with exposed electrical terminals. Disconnect-
ing this cable will help prevent personal injury and
damage to the vehicle. The ignition must also be in
B unless otherwise noted.
Notice: Any time the air cleaner is removed, the intake
opening should be covered. This will protect against ac-
cidental entrance of foreign material, which could follow
the intake passage into the cylinder and cause exten-
sive damage when the engine is started.

GENERAL ENGINE INFORMATION 1A–3
DAEWOO M-150 BL2
COMPONENT LOCATOR
ENGINE COMPARTMENT (TYPICAL)
(Left–Hand Drive Shown, Right–Hand Drive Similar)
D102A401
1 Power Steering Oil Reservoir
2 Coolant Reservoir
3 Canister
4 Canister Solenoid
5 Manifold Absolute Pressure (MAP) Sensor
6 Intake Manifold
7 Ignition Coil
8 Idle Air Control (IAC) Valve
9 Throttle Position (TP) Sensor
10 Throttle Body
11 Brake Fluid Reservoir
12 Wiper Motor13 Battery
14 Fuse Box
15 Air Cleaner Housing
16 Resonator
17 PCV Hose
18 Distributor
19 Exhaust Manifold
20 Snorkel
21 Engine
22 Washer Fluid Reservoir
23 Oil Level Gauge
24 Oil Filler Cap

1A–4 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
ENGINE COMPARTMENT (EURO III)
(Left–Hand Drive Shown, Right–Hand Drive Similar)
MAA1A010
1 Power Steering Oil Reservoir
2 Coolant Reservoir
3 Canister Purge Solenoid
4 Manifold Absolute Pressure (MAP) Sensor
5 Intake Manifold
6 Throttle Position (TP) Sensor
7 Throttle Body
8 Idle Air Control (IAC) Valve
9 Brake Fluid Reservoir
10 Wiper Motor11 Battery
12 Fuse Box
13 Air Cleaner Housing
14 Resonator
15 Electronic Ignition System Ignition Coil
16 Exhaust Manifold
17 Snorkel
18 Engine
20 Washer Fluid Reservoir
19 Oil Level Gauge
21 Oil Filler Cap

1A–14 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
 Application Description
  Maximum Speed 144 km/h (90 mph)
 Vehicle Capacity Gradeability 0.420 tan θ
 
Vehicle Capacity
 Minimum Turning Radius 4.5 m (14.8 ft)
  Bore × Stroke 68.5 × 72.0 mm (2.70 × 2.83 inch)
  Displacement 796 cm3 (48.6 in3)
  Compression Ratio 9.3 : 1
  Maximum Power 37.5 KW (6,000 rpm)
 
Engine Information
 Maximum Torque 68.6 Nm (50.59 lb-ft) (at 4,600 rpm)
Ignition Timing (Ignition Sequence)5 BTDC (1–3–2) / 10 BTDC (1–3–2)   
Air Conditioning System (ON)
 
1,000 ± 50 rpm  Idle Speed Air Conditioning System (OFF) 950 rpm  Engine Overhead Cam L–3 
 
 
 Ignition Type
 
 Direct Ignition System (DIS) /
High Energy Ignition (HEI)
  Distributor Optical Sensor Type
  Starter SD 80
   Unleaded BPR5EY–11, RN9YC4, WR8DCX
  Spark–Plug Leaded BPR5EY, RN9YC, WR8DC
  Fuel Injection Type MPI
  Fuel Pump Electric Motor Pump
Engine Part TypeFuel FilterCartridge Engine Part Type 
Lubricating Type
 
Forced Feed Type  Oil Pump Rotary Pump Type  Cooling Type Forced Water Circulation  Radiator Cross – Flow  Water Pump Centrifugal  Thermostat Pellet Type
  Air Cleaner Element Non Woven Fablic
  Muffler Catalytic Converter, Closed Circuit
  Battery MF
Engine PartEngine OilSJ Grade
SAE 5W30, SAE 10W30, SAE 15W40
CapacityRefrigerantFour Seasons   
Engine Disassembly
 
3.0 L (3.17 qt)   Oil Change (Including filter) 2.7 L (2.85 qt)  Engine Oil Oil Change (Not including filter) 2.5 L (2.64 qt)   Oil Level Gauge 1 L (1.06 qt) (MIN to MAX)  Coolant 3.8 L (4.02 qt) Engine Information Battery 12V–35 AH, 246 CCA
 Engine Information  

Generator

65 A
  Starter 0.8 kW
   Output Capacity 90 – 133 Lph
  Fuel Pump Output Pressure 380 kPa (55.1 Psi)
  Fuel Tank Capacity 35 L (9.2 gal), 38 L (10 gal)

DAEWOO M-150 BL2
SECTION 1B
SOHC ENGINE MECHANICAL
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 1B-2. . . . . . . . . . . . . . . . . .
Engine Type 1B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Lubrication 1B-2. . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Valve Train 1B-2. . . . . . . . . . . . . .
Engine Block 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crankshaft 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Rod 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . .
Piston, Piston Ring and Piston Pin 1B-3. . . . . . . . . . .
Timing Belt and Pulley 1B-4. . . . . . . . . . . . . . . . . . . . .
Engine Mount 1B-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Locator 1B-5. . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head 1B-5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Block 1B-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manifold & Air Flow System 1B-7. . . . . . . . . . . . . . . . .
Timing Belt & Engine Mount 1B-8. . . . . . . . . . . . . . . .
Diagnostic Information and Procedure 1B-9. . . . . . .
Compression Pressure Check 1B-9. . . . . . . . . . . . . . .
Oil Pressure Check 1B-9. . . . . . . . . . . . . . . . . . . . . . . .
Adjustment of Valve Clearance 1B-10. . . . . . . . . . . . .
Ignition Timing Check and Adjustment
(Typical) 1B-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valve Timing Check and Adjustment 1B-12. . . . . . . .
Repair Instructions 1B-14. . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 1B-14. . . . . . . . . . . . . . . . . . . . . . . . . Air Filter Assembly 1B-14. . . . . . . . . . . . . . . . . . . . . . .
Air Filter Element 1B-15. . . . . . . . . . . . . . . . . . . . . . . . .
Positive Crankcase Ventilation (PCV) Hose
and Valve 1B-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intake Manifold 1B-16. . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold (Typical) 1B-18. . . . . . . . . . . . . . . . .
Exhaust Manifold (Euro III) 1B-20. . . . . . . . . . . . . . . .
Timing Belt 1B-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pan 1B-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump 1B-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distributor Case 1B-26. . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Gasket 1B-28. . . . . . . . . . . . . . . . .
Engine Mount Damping Block 1B-32. . . . . . . . . . . . . .
Engine Mount Front Damping Bush 1B-34. . . . . . . . .
Engine Assembly 1B-35. . . . . . . . . . . . . . . . . . . . . . . . .
Unit Repair 1B-47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Valve Train
Components 1B-47. . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Block Components 1B-59. . . . . . . . . . . . . . . . .
Specifications 1B-71. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Specifications 1B-71. . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 1B-73. . . . . . . . . .
Special Tools 1B-75. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools Table 1B-75. . . . . . . . . . . . . . . . . . . . . . .

DAEWOO M-150 BL2
SECTION 1D
ENGINE COOLING
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 1D-2. . . . . . . . . . . . . . . . . .
General Description 1D-2. . . . . . . . . . . . . . . . . . . . . . .
Radiator 1D-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Surge Tank 1D-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coolant Pump 1D-3. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermostat 1D-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric Cooling Fan 1D-3. . . . . . . . . . . . . . . . . . . . . . .
Engine Coolant Temperature Sensor 1D-4. . . . . . . . .
Coolant Temperature Sensor 1D-4. . . . . . . . . . . . . . . .
Component Locator 1D-5. . . . . . . . . . . . . . . . . . . . . . . .
Coolant Hose and Components 1D-5. . . . . . . . . . . . .
Radiator/Fan 1D-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedure 1D-7. . . . . . .
Coolant Leaks Test 1D-7. . . . . . . . . . . . . . . . . . . . . . . .
Surge Tank Cap Test 1D-7. . . . . . . . . . . . . . . . . . . . . . .
Thermostat Test 1D-7. . . . . . . . . . . . . . . . . . . . . . . . . . . Cooling System Diagnosis 1D-8. . . . . . . . . . . . . . . . . .
Repair Instructions 1D-9. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 1D-9. . . . . . . . . . . . . . . . . . . . . . . . . .
Draining and Refilling the Cooling System 1D-9. . . .
Surge Tank 1D-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric Cooling Fan 1D-11. . . . . . . . . . . . . . . . . . . . . .
Radiator 1D-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermostat (Typical) 1D-12. . . . . . . . . . . . . . . . . . . . . .
Thermostat (Euro III) 1D-13. . . . . . . . . . . . . . . . . . . . . .
Coolant Temperature Sensor 1D-14. . . . . . . . . . . . . . .
Engine Coolant Temperature Sensor 1D-15. . . . . . . .
Coolant Pump 1D-15. . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 1D-17. . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Specifications 1D-17. . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 1D-18. . . . . . . . . .

ENGINE COOLING 1D–11
DAEWOO M-150 BL2
D102D505
Installation Procedure
1. Install the surge tank to the vehicle.
Install the surge tank with pressing down (1).
Connect the overflow hoses to the surge tank (2).
2. Secure the overflow hoses to the surge tank with the
hose clamps.
3. Fill the surge tank with coolant to the MAX mark.
D102D506
ELECTRIC COOLING FAN
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the electric cooling fan assembly.
Disconnect the cooling fan electrical connector (1).
Remove the bolts (2).
Remove the electric cooling fan assembly (3).
3.5–4.5 Nm
D12D507A
Installation Procedure
1. Install the electric cooling fan assembly with the bolts.
Tighten
Tighten the bolts to 3.5–4.5 Nm (31–40 lb-in).
2. Connect the cooling fan electrical connector.
3. Connect the negative battery cable.
D12D5081
RADIATOR
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the lower radiator hose and drain the en-
gine cooling system. Refer to “Draining and Refilling
the Cooling System” in this section.
3. Disconnect the upper radiator hose and the surge
tank hose.
Loosen the upper radiator hose clamp and discon-
nect the upper radiator hose (1).
Loosen the surge tank hose clamp and disconnect
the surge tank hose (2).

1D–12 ENGINE COOLING
DAEWOO M-150 BL2
D12D5091
4. Remove the electric cooling fan.
Refer to “Electric Cooling Fan” in this section.
5. Remove the radiator.
Remove the bolts (1).
Remove the radiator support brackets (2).
Remove the radiator (3).
6. Check the radiator for breaking, clog or other dam-
age.
Important: The radiator still contains a substantial
amount of coolant. Drain the remainder of the coolant
from the radiator into a drain pan.
D12D5101
Installation Procedure
1. Install the radiator with the mounting bolts (1) and the
support brackets (2).
Tighten
Tighten the support bracket bolts to 3.5–4.5 Nm
(31–40 lb-in).
2. Install the electric cooling fan.
Refer to “Electric Cooling Fan” in this section.
D12D5111
3. Connect the upper radiator hose to the radiator (1).
4. Connect the surge tank hose to the radiator (2).
5. Secure each hose with hose clamps.
6. Refill the engine cooling system. Refer to “Draining
and Refilling the Cooling System” in this section.
7. Connect the negative battery cable.
D102D512
THERMOSTAT (TYPICAL)
Removal Procedure
Caution: To prevent personal injury, do not remove
the surge tank cap while the engine and the radiator
are hot because the heat causes the system to re-
main under pressure. Scalding fluid and steam may
be blown out under pressure.
1. Remove air filter assembly. Refer to Section 1B,
SOHC Engine Mechanical.
2. Disconnect the lower radiator hose and drain the
coolant. Refer to “Drain and Refilling the Cooling Sys-
tem”
3. Disconnect the upper radiator hose.