2003 CHRYSLER CARAVAN roof rack

(2) Drain the engine cooling system. (Refer to 7 -
COOLING - STANDARD PROCEDURE - COOLING
SYSTEM DRAIN).
(3) Disconnect and isolate the battery negative
cable.
(4) Raise and support the vehicle.
(5) Disconnect the underbody refrigerant line seal-
ing plate from the rear heater-A/C unit evaporator
extension line sealing plate that extends through the
rear floor panel behind the right rear wheel housing
(Fig. 6).
(6) Remove the seals from the liquid line and suc-
tion line fittings and discard.
(7) Install plugs in, or tape over the opened liquid
line and suction line fittings and both ports in the
evaporator extension line sealing plate.
(8) Remove the three nuts that secure the rear
heater-A/C unit mounting studs to the rear floor
panel behind the right rear wheel housing (Fig. 7).
(9) Lower the vehicle.
(10) Remove the right quarter trim panel and
right D-pillar trim panel from the quarter inner
panel. (Refer to 23 - BODY/INTERIOR/QUARTER
TRIM PANEL - REMOVAL).
(11) Remove the rear A/C distribution duct from
the rear heater-A/C unit and the rear roof duct.
(Refer to 24 - HEATING & AIR CONDITIONING/
DISTRIBUTION - REAR/AUXILIARY A/C DISTRI-
BUTION DUCT - REMOVAL).
(12) Disconnect the body wire harness connector
for the rear heater-A/C unit housing from the rear
HVAC wire harness connector located near the
expansion valve at the back of the unit.
(13) Remove the two screws that secure the top of
the quarter trim panel attaching bracket to the quar-
ter inner panel.(14) Remove the two screws that secure the bottom
of the quarter trim panel attaching bracket to the
rear heater-A/C unit housing.
(15) Remove the rear heater distribution duct from
the right quarter inner panel. (Refer to 24 - HEAT-
ING & AIR CONDITIONING/DISTRIBUTION -
REAR/REAR HEATER DISTRIBUTION DUCT -
REMOVAL).
(16) Take the proper precautions to protect the
carpeting below the rear heater core from spilled
engine coolant and have absorbent toweling readily
available to clean up any spills.
(17) Disconnect the heater hoses at the rear heater
core. (Refer to 24 - HEATING & AIR CONDITION-
ING/PLUMBING - REAR/HEATER HOSE - REMOV-
AL).
(18) Install plugs in, or tape over the opened
heater core fittings and both heater hoses.
(19) Use absorbent toweling to mop up any engine
coolant spills from the preceding operation.
(20) Remove the screw that secures the back of the
rear heater-A/C unit housing to the right D-pillar
(Fig. 8).
(21) Remove the screw that secures the front of
the rear heater-A/C unit housing to the right quarter
inner panel.
(22) Lift the rear heater-A/C unit housing up far
enough for the lower mounting studs and the evapo-
rator extension lines to clear the mounting holes in
the rear floor panel.
(23) Remove the rear heater-A/C unit housing from
the vehicle.
(24) Use absorbent toweling to mop up any engine
coolant spills from the preceding operation.
Fig. 6 Refrigerant Lines
1 - UNDERBODY REFRIGERANT LINE SEALING PLATE
Fig. 7 Rear Heater-A/C Unit Mounting Studs
1 - REAR HEATER-A/C UNIT MOUNTING STUDS
RSDISTRIBUTION - REAR24-57
REAR HEATER-A/C HOUSING (Continued)
ProCarManuals.com

MANUAL ADJUSTER - INSTALLATION,
FRONT SEAT TRACK..................23-94
MANUAL ADJUSTER - REMOVAL, FRONT
SEAT TRACK........................23-94
MANUAL THREE ZONE - DESCRIPTION....24-1
MANUAL THREE ZONE - OPERATION......24-3
MANUAL TRACK - INSTALLATION,
FRONT SEAT RISER...................23-93
MANUAL TRACK - REMOVAL, FRONT
SEAT RISER.........................23-93
MANUAL TRANSAXLE - ASSEMBLY, T850 . 21-42
MANUAL TRANSAXLE - DESCRIPTION,
T850..............................21-21
MANUAL TRANSAXLE - DISASSEMBLY,
T850..............................21-35
MANUAL TRANSAXLE - INSTALLATION,
T850..............................21-51
MANUAL TRANSAXLE - OPERATION,
T850..............................21-24
MANUAL TRANSAXLE - REMOVAL, T850 . . 21-31
MANUAL TRANSAXLE - SPECIFICATIONS,
T850..............................21-56
MANUFACTURER PLATE - DESCRIPTION . Intro.-11
MAP SENSOR - DESCRIPTION..........14-30
MAP SENSOR - OPERATION............14-30
MASTER CYLINDER - LHD -
INSTALLATION........................6-10
MASTER CYLINDER - LHD - REMOVAL.....6-9
MASTER CYLINDER - RHD -
INSTALLATION.........................6-9
MASTER CYLINDER - RHD - REMOVAL.......6-8
MASTER CYLINDER BLEEDING -
STANDARD PROCEDURE................5-35
MASTER CYLINDER (FLUID RESERVOIR)
- ASSEMBLY.........................5-38
MASTER CYLINDER (FLUID RESERVOIR)
- DISASSEMBLY......................5-37
MATCH MOUNTING - STANDARD
PROCEDURE, TIRE AND WHEEL..........22-7
MATS - INSTALLATION, CARPETS AND
FLOOR.............................23-75
MATS - REMOVAL, CARPETS AND
FLOOR.............................23-74
MEASUREMENT - STANDARD
PROCEDURE, CURB HEIGHT.............2-54
MEASUREMENTS - SPECIFICATIONS,
GAP AND FLUSH....................23-121
MEASURING BEARING CLEARANCE
USING PLASTIGAGE - STANDARD
PROCEDURE.....................9-12,9-84
MEASURING CAMSHAFT END PLAY -
STANDARD PROCEDURE................9-29
MEASURING CONNECTING ROD
BEARING CLEARANCE - STANDARD
PROCEDURE........................9-120
MEASURING CRANKSHAFT END PLAY -
STANDARD PROCEDURE...............9-125
MEASURING TIMING CHAIN WEAR -
STANDARD PROCEDURE...............9-153
MECHANICAL - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS........9-6,9-80
MECHANISM - INSTALLATION,
GEARSHIFT.........................21-89
MECHANISM - REMOVAL, GEARSHIFT....21-87
MEMORIES, OPERATION - FUEL
CORRECTION OR ADAPTIVE............14-20
MEMORY SEAT/MIRROR MODULE -
DESCRIPTION.......................8E-10
MEMORY SEAT/MIRROR MODULE -
DIAGNOSIS AND TESTING
.............8E-10
MEMORY SEAT/MIRROR MODULE -
INSTALLATION
.......................8E-10
MEMORY SEAT/MIRROR MODULE -
OPERATION
.........................8E-10
MEMORY SEAT/MIRROR MODULE -
REMOVAL
..........................8E-10
MEMORY SET SWITCH - DESCRIPTION
. . . 8N-55
MEMORY SET SWITCH - INSTALLATION
. . 8N-56
MEMORY SET SWITCH - OPERATION
....8N-56
MEMORY SET SWITCH - REMOVAL
......8N-56
MEMORY SWITCH - DIAGNOSIS AND
TESTING
...........................8N-56
MEMORY SYSTEM - DESCRIPTION
......8N-51
MEMORY SYSTEM - DIAGNOSIS AND
TESTING
...........................8N-53
MEMORY SYSTEM - OPERATION
........8N-52
METRIC SYSTEM - DESCRIPTION
......Intro.-6MINI-TRIP COMPUTER - DIAGNOSIS
AND TESTING, COMPASS.............8M-10
MIRROR - DESCRIPTION, AUTOMATIC
DAY / NIGHT........................8N-47
MIRROR - DIAGNOSIS AND TESTING,
AUTOMATIC DAY / NIGHT..............8N-47
MIRROR - INSTALLATION, REAR VIEW . . . 23-80
MIRROR - INSTALLATION, SIDE VIEW....23-57
MIRROR - OPERATION, AUTOMATIC DAY
/ NIGHT............................8N-47
MIRROR - REMOVAL, REAR VIEW.......23-79
MIRROR - REMOVAL, SIDE VIEW........23-57
MIRROR - REMOVAL, SIDEVIEW........8N-49
MIRROR - STANDARD PROCEDURE,
HEATED.............................8G-6
MIRROR GLASS - INSTALLATION, SIDE
VIEW..............................23-58
MIRROR GLASS - REMOVAL, SIDE VIEW . . 23-58
MIRROR SWITCH - DESCRIPTION........8G-5
MIRROR SWITCH - EXPORT -
DESCRIPTION, POWER FOLDAWAY......8N-48
MIRROR SWITCH - EXPORT -
INSTALLATION, POWER FOLDAWAY......8N-49
MIRROR SWITCH - EXPORT -
OPERATION, POWER FOLDAWAY........8N-48
MIRROR SWITCH - EXPORT - REMOVAL,
POWER FOLDAWAY..................8N-48
MIRROR SWITCH - OPERATION..........8G-5
MIRROR TEST - DIAGNOSIS AND
TESTING, HEATED.....................8G-5
MIRRORS - DESCRIPTION, HEATED........8G-5
MIRRORS - DESCRIPTION, POWER......8N-45
MIRRORS - DIAGNOSIS AND TESTING,
POWER............................8N-46
MIRRORS - OPERATION, HEATED........8G-5
MIRRORS - OPERATION, POWER........8N-45
MISALIGNMENT - DIAGNOSIS AND
TESTING, DRIVE PLATE.................6-6
MODE DOOR ACTUATOR - DESCRIPTION . . 24-24
MODE DOOR ACTUATOR -
INSTALLATION..................24-25,24-36
MODE DOOR ACTUATOR - OPERATION . . . 24-24
MODE DOOR ACTUATOR - REMOVAL....24-25,
24-36
MODE, OPERATION - DRB IIITS TAT E
DISPLAY TEST........................25-9
MODES OF OPERATION - OPERATION....14-18
MODULAR CLUTCH ASSY - 2.4L GAS -
INSTALLATION........................6-11
MODULAR CLUTCH ASSY - 2.4L GAS -
REMOVAL...........................6-11
MODULE - DESCRIPTION, BODY
CONTROL...........................8E-3
MODULE - DESCRIPTION, FRONT
CONTROL...........................8E-7
MODULE - DESCRIPTION, FUEL PUMP....14-8
MODULE - DESCRIPTION, HEATED SEAT . . . 8E-8
MODULE - DESCRIPTION, INTEGRATED
POWER..........................8W-97-3
MODULE - DESCRIPTION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - DESCRIPTION, POWER . . 24-25,24-37
MODULE - DESCRIPTION, POWER
LIFTGATE CONTROL..................8E-10
MODULE - DESCRIPTION, REAR
DRIVELINE...........................3-23
MODULE - DESCRIPTION, REMOTE
KEYLESS ENTRY.....................8N-43
MODULE - DESCRIPTION, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - DESCRIPTION, SIDE IMPACT
AIRBAG CONTROL...................8O-17
MODULE - DESCRIPTION, SLIDING
DOOR CONTROL.....................8E-19
MODULE - DESCRIPTION,
TRANSMISSION CONTROL.............8E-20
MODULE - DIAGNOSIS AND TESTING,
FRONT CONTROL.....................8E-7
MODULE - DIAGNOSIS AND TESTING,
HEATED SEAT
........................8E-9
MODULE - DIAGNOSIS AND TESTING,
MEMORY SEAT/MIRROR
...............8E-10
MODULE - DIAGNOSIS AND TESTING,
REMOTE KEYLESS ENTRY
.............8N-43
MODULE - EXPORT - DESCRIPTION,
ANTENNA
...........................8A-6
MODULE - EXPORT - DIAGNOSIS AND
TESTING, ANTENNA
...................8A-7MODULE - EXPORT - INSTALLATION,
ANTENNA...........................8A-7
MODULE - EXPORT - OPERATION,
ANTENNA...........................8A-6
MODULE - EXPORT - REMOVAL,
ANTENNA...........................8A-7
MODULE - INSTALLATION, BODY
CONTROL...........................8E-5
MODULE - INSTALLATION, FRONT
CONTROL...........................8E-8
MODULE - INSTALLATION, FUEL PUMP....14-9
MODULE - INSTALLATION, HEATED SEAT . . 8E-10
MODULE - INSTALLATION, INTEGRATED
POWER..........................8W-97-4
MODULE - INSTALLATION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - INSTALLATION, POWER . 24-26,24-38
MODULE - INSTALLATION, POWER
LIFTGATE CONTROL..................8E-11
MODULE - INSTALLATION, REMOTE
KEYLESS ENTRY.....................8N-44
MODULE - INSTALLATION, SENTRY KEY
IMMOBILIZER.......................8E-19
MODULE - INSTALLATION, SIDE IMPACT
AIRBAG CONTROL...................8O-17
MODULE - INSTALLATION, SLIDING
DOOR CONTROL.....................8E-20
MODULE - INSTALLATION, WIPER.......8R-18
MODULE - OPERATION, BODY CONTROL . . . 8E-3
MODULE - OPERATION, FRONT
CONTROL...........................8E-7
MODULE - OPERATION, FUEL PUMP........14-8
MODULE - OPERATION, HEATED SEAT.....8E-9
MODULE - OPERATION, INTEGRATED
POWER..........................8W-97-3
MODULE - OPERATION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - OPERATION, POWER....24-26,24-37
MODULE - OPERATION, POWER
LIFTGATE CONTROL..................8E-11
MODULE - OPERATION, REAR
DRIVELINE...........................3-23
MODULE - OPERATION, REMOTE
KEYLESS ENTRY.....................8N-43
MODULE - OPERATION, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - OPERATION, SIDE IMPACT
AIRBAG CONTROL...................8O-17
MODULE - OPERATION, SLIDING DOOR
CONTROL..........................8E-19
MODULE - OPERATION, TRANSMISSION
CONTROL..........................8E-20
MODULE - REMOVAL, BODY CONTROL....8E-4
MODULE - REMOVAL, FRONT CONTROL . . . 8E-8
MODULE - REMOVAL, FUEL PUMP........14-8
MODULE - REMOVAL, HEATED SEAT......8E-9
MODULE - REMOVAL, INTEGRATED
POWER..........................8W-97-4
MODULE - REMOVAL, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - REMOVAL, POWER.....24-26,24-37
MODULE - REMOVAL, POWER LIFTGATE
CONTROL..........................8E-11
MODULE - REMOVAL, REMOTE KEYLESS
ENTRY
.............................8N-44
MODULE - REMOVAL, SENTRY KEY
IMMOBILIZER
.......................8E-18
MODULE - REMOVAL, SIDE IMPACT
AIRBAG CONTROL
...................8O-17
MODULE - REMOVAL, SLIDING DOOR
CONTROL
..........................8E-19
MODULE - REMOVAL, WIPER
...........8R-18
MODULE - SPECIFICATIONS, REAR
DRIVELINE
...........................3-34
MODULE, BENCH SEAT - REMOVAL,
CHILD SEAT
.........................23-86
MODULE LAMP REPLACEMENT -
STANDARD PROCEDURE
...............8M-3
MODULE NOISE - DIAGNOSIS AND
TESTING, REAR DRIVELINE
.............3-24
MODULE OPERATION - DIAGNOSIS AND
TESTING, REAR DRIVELINE
.............3-26
MOLDING - INSTALLATION, FRONT
DOOR INNER BELT
..................23-112
MOLDING - INSTALLATION, FRONT
DOOR OUTER BELT
..................23-110
MOLDING - INSTALLATION, ROOF JOINT
. . 23-57
20 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

MOLDING - REMOVAL, FRONT DOOR
INNER BELT........................23-112
MOLDING - REMOVAL, FRONT DOOR
OUTER BELT.......................23-110
MOLDING - REMOVAL, ROOF JOINT......23-57
MOLDINGS - INSTALLATION, BODY SIDE . . 23-45
MOLDINGS - REMOVAL, BODY SIDE.....23-44
MONITORED COMPONENT -
DESCRIPTION........................25-1
MONITORED SYSTEMS - DESCRIPTION....25-6
MONITORING - DESCRIPTION, TIRE
PRESSURE..........................22-9
MONITORING - OPERATION, TIRE
PRESSURE..........................22-9
MOTOR - DESCRIPTION, BLOWER . . 24-43,24-53
MOTOR - DESCRIPTION, IDLE AIR
CONTROL..........................14-28
MOTOR - DESCRIPTION, LIFTGATE......8N-15
MOTOR - DESCRIPTION, SLIDING DOOR . . 8N-30
MOTOR - DIAGNOSIS AND TESTING,
BLOWER......................24-43,24-54
MOTOR - DIAGNOSIS AND TESTING,
DOOR LOCK........................8N-41
MOTOR - DIAGNOSIS AND TESTING,
RADIATOR FAN.......................7-29
MOTOR - DIAGNOSIS AND TESTING,
VENT WINDOW......................8N-63
MOTOR - EXPORT - DIAGNOSIS AND
TESTING, HEADLAMP LEVELING........8L-14
MOTOR - EXPORT - INSTALLATION,
HEADLAMP LEVELING.................8L-15
MOTOR - EXPORT - INSTALLATION,
HEADLAMP WASHER PUMP............8R-13
MOTOR - EXPORT - REMOVAL,
HEADLAMP LEVELING.................8L-14
MOTOR - EXPORT - REMOVAL,
HEADLAMP WASHER PUMP............8R-12
MOTOR - INSTALLATION, BLOWER . 24-46,24-56
MOTOR - INSTALLATION, FRONT
WASHER PUMP......................8R-8
MOTOR - INSTALLATION, FRONT WIPER . . . 8R-9
MOTOR - INSTALLATION, IDLE AIR
CONTROL..........................14-29
MOTOR - INSTALLATION, LIFTGATE......8N-15
MOTOR - INSTALLATION, REAR WASHER
PUMP.............................8R-14
MOTOR - INSTALLATION, REAR WIPER . . . 8R-15
MOTOR - INSTALLATION, SLIDING DOOR . 8N-31
MOTOR - INSTALLATION, SLIDING DOOR
LOCK..............................8N-44
MOTOR - INSTALLATION, SUNROOF.....23-118
MOTOR - INSTALLATION, VENT WINDOW . 8N-64
MOTOR - OPERATION, BLOWER....24-43,24-54
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-28
MOTOR - OPERATION, LIFTGATE........8N-15
MOTOR - OPERATION, SLIDING DOOR . . . 8N-30
MOTOR - REMOVAL, BLOWER.....24-46,24-56
MOTOR - REMOVAL, FRONT WASHER
PUMP..............................8R-8
MOTOR - REMOVAL, FRONT WIPER......8R-9
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-29
MOTOR - REMOVAL, LIFTGATE.........8N-15
MOTOR - REMOVAL, REAR WASHER
PUMP.............................8R-13
MOTOR - REMOVAL, REAR WIPER......8R-14
MOTOR - REMOVAL, SLIDING DOOR.....8N-30
MOTOR - REMOVAL, SLIDING DOOR
LOCK..............................8N-44
MOTOR - REMOVAL, SUNROOF........23-118
MOTOR - REMOVAL, VENT WINDOW.....8N-63
MOTOR - REMOVAL, WINDOW..........8N-64
MOTOR RELAY - DESCRIPTION,
BLOWER......................24-13,24-32
MOTOR RELAY - DIAGNOSIS AND
TESTING, BLOWER..............24-14,24-33
MOTOR RELAY - INSTALLATION,
BLOWER......................24-14,24-33
MOTOR RELAY - OPERATION, BLOWER
. . 24-13,
24-32
MOTOR RELAY - REMOVAL, BLOWER
....24-14,
24-33
MOTOR RESISTOR - DESCRIPTION,
BLOWER
......................24-14,24-34
MOTOR RESISTOR - DIAGNOSIS AND
TESTING, BLOWER
..............24-15,24-34
MOTOR RESISTOR - INSTALLATION,
BLOWER
......................24-16,24-35MOTOR RESISTOR - OPERATION,
BLOWER......................24-15,24-34
MOTOR RESISTOR - REMOVAL,
BLOWER......................24-16,24-35
MOUNT - INSTALLATION, FRONT....9-131,9-49
MOUNT - INSTALLATION, LEFT......9-133,9-50
MOUNT - INSTALLATION, REAR.....9-134,9-50
MOUNT - INSTALLATION, RIGHT....9-135,9-51
MOUNT - REMOVAL, FRONT........9-131,9-49
MOUNT - REMOVAL, LEFT.........9-133,9-49
MOUNT - REMOVAL, REAR.........9-133,9-50
MOUNT - REMOVAL, RIGHT........9-135,9-51
MOUNT BUSHINGS - INSTALLATION,
FRONT CROSSMEMBER...............13-12
MOUNT BUSHINGS - REMOVAL, FRONT
CROSSMEMBER.....................13-12
MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH...........8L-7
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH...............8L-6
MOUNTING - DESCRIPTION, ENGINE . 9-131,9-48
MOUNTING - STANDARD PROCEDURE,
TIRE AND WHEEL MATCH...............22-7
MOUNTING BRACKET - 2.4L ENGINE -
INSTALLATION, COMPRESSOR..........24-66
MOUNTING BRACKET - 2.4L ENGINE -
REMOVAL, COMPRESSOR...............24-65
MOUNTING STUDS - FRONT -
INSTALLATION, WHEEL................22-21
MOUNTING STUDS - FRONT - REMOVAL,
WHEEL............................22-20
MOUNTING STUDS - REAR -
INSTALLATION, WHEEL................22-22
MOUNTING STUDS - REAR - REMOVAL,
WHEEL............................22-21
MOUNTS - FRONT - INSTALLATION,
SPRING.............................2-42
MOUNTS - FRONT - REMOVAL, SPRING . . . 2-42
MOUNTS - REAR - INSTALLATION,
SPRING.............................2-43
MOUNTS - REAR - REMOVAL, SPRING....2-43
MUFFLER - INSTALLATION..............11-7
MUFFLER - REMOVAL..................11-7
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING
.......................8L-21
MULTI-FUNCTION SWITCH -
INSTALLATION
.......................8L-21
MULTI-FUNCTION SWITCH - REMOVAL
. . . 8L-21
NAME PLATES - ADHESIVE ATTACHED -
INSTALLATION, EXTERIOR
.............23-50
NAME PLATES - ADHESIVE ATTACHED -
REMOVAL, EXTERIOR
.................23-50
NAME PLATES - TAPE ATTACHED -
INSTALLATION, EXTERIOR
.............23-50
NAME PLATES - TAPE ATTACHED -
REMOVAL, EXTERIOR
.................23-50
NATURAL VAC LEAK DETECTION ASSY -
INSTALLATION
.......................25-13
NATURAL VAC LEAK DETECTION ASSY -
REMOVAL
..........................25-13
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP TO FILLER
..............7-27
NGC CONTROLLER - REMOVAL
.........8E-17
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY
.....................8N-47
NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC DAY
.............8N-47
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY
.....................8N-47
NO CUP HOLDER - INSTALLATION,
QUAD BUCKET SEAT SIDE SHIELD
.......23-96
NO CUP HOLDER - REMOVAL, QUAD
BUCKET SEAT SIDE SHIELD
............23-96
NOISE - DIAGNOSIS AND TESTING,
EXCESSIVE EXHAUST SYSTEM
...........11-2
NOISE - DIAGNOSIS AND TESTING,
REAR DRIVELINE MODULE
..............3-24
NOISE - DIAGNOSIS AND TESTING, TIRE
. . 22-14
NOISE - DIAGNOSIS AND TESTING,
WIND
...............................23-3
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, COMPRESSOR
...............24-63NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, HYDRAULIC LASH
ADJUSTER...........................9-34
NOISE SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO.................8A-11
NOISE SUPPRESSION COMPONENTS -
OPERATION, RADIO..................8A-12
NON-ABS JUNCTION BLOCK -
DESCRIPTION........................5-33
NON-ABS JUNCTION BLOCK -
INSTALLATION........................5-33
NON-ABS JUNCTION BLOCK -
OPERATION..........................5-33
NON-ABS JUNCTION BLOCK - REMOVAL . . . 5-33
NON-MONITORED CIRCUITS -
OPERATION..........................25-5
NOT FILL - DIAGNOSIS AND TESTING,
VEHICLE DOES......................25-16
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION....................Intro.-9
NVLD - INSTALLATION, WITH...........25-20
NVLD - REMOVAL, WITH..............25-19
O2 SENSOR - DESCRIPTION............14-31
O2 SENSOR - OPERATION.............14-31
OBTAINING DIAGNOSTIC TROUBLE
CODES - STANDARD PROCEDURE.......8E-15
OCCUPANT RESTRAINT CONTROLLER -
DESCRIPTION........................8O-7
OCCUPANT RESTRAINT CONTROLLER -
INSTALLATION.......................8O-7
OCCUPANT RESTRAINT CONTROLLER -
OPERATION..........................8O-7
OCCUPANT RESTRAINT CONTROLLER -
REMOVAL...........................8O-7
OIL - DESCRIPTION, FLEXIBLE FUEL
ENGINE..............................0-3
OIL - DESCRIPTION, REFRIGERANT......24-90
OIL - DIESEL ENGINES - DESCRIPTION,
ENGINE..............................0-6
OIL - OPERATION, REFRIGERANT........24-90
OIL AND FILTER CHANGE - STANDARD
PROCEDURE, ENGINE.............9-137,9-53
OIL AND LUBRICANTS - DESCRIPTION,
ENGINE..............................0-1
OIL COOLER - DESCRIPTION,
TRANSMISSION.......................7-37
OIL COOLER - INSPECTION,
TRANSMISSION.......................7-37
OIL COOLER - INSTALLATION,
TRANSMISSION.......................7-37
OIL COOLER & LINES - DESCRIPTION....9-138
OIL COOLER & LINES - INSTALLATION . . . 9-138
OIL COOLER & LINES - OPERATION......9-138
OIL COOLER & LINES - REMOVAL.......9-138
OIL COOLER - REMOVAL,
TRANSMISSION.......................7-37
OIL COOLER LINES - INSTALLATION,
TRANSMISSION.......................7-38
OIL COOLER LINES - REMOVAL,
TRANSMISSION.......................7-38
OIL FILTER - DESCRIPTION.............9-53
OIL FILTER - INSTALLATION........9-139,9-53
OIL FILTER - REMOVAL............9-139,9-53
OIL FILTER ADAPTER - INSTALLATION....9-139
OIL FILTER ADAPTER - REMOVAL.......9-139
OIL GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE.........9-10,9-86
OIL LEAK INSPECTION - DIAGNOSIS
AND TESTING, ENGINE..............9-8,9-82
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-90
OIL LEVEL CHECK - STANDARD
PROCEDURE, ENGINE.................9-137
OIL LEVEL CHECK, STANDARD
PROCEDURE - ENGINE.................9-53
OIL PAN - CLEANING.................9-140
OIL PAN - INSPECTION................9-140
OIL PAN - INSTALLATION..........9-140,9-54
OIL PAN - REMOVAL..............9-140,9-54
OIL PRESSURE - DIAGNOSIS AND
TESTING, CHECKING ENGINE
............9-52
OIL PRESSURE - DIAGNOSIS AND
TESTING, ENGINE
....................9-136
OIL PRESSURE RELIEF VALVE -
INSTALLATION
.......................9-141
OIL PRESSURE RELIEF VALVE -
REMOVAL
..........................9-141
OIL PRESSURE SWITCH - DESCRIPTION
. . 9-141
RSINDEX21
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

RETRACTOR - SECOND ROW - LEFT
OUTBOARD - REMOVAL, SEAT BELT.....8O-16
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD - INSTALLATION, SEAT
BELT ..............................8O-14
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD - REMOVAL, SEAT BELT.....8O-14
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT.............8O-15
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC - LWB -
REMOVAL, SEAT BELT................8O-15
RETRAIN - STANDARD PROCEDURE,
TIRE PRESSURE SENSOR..............22-10
RETURN - PCM INPUT - OPERATION,
SENSOR............................8E-15
RHD - DESCRIPTION...................5-35
RHD - INSTALLATION..........5-39,5-47,5-95
RHD - INSTALLATION, MASTER
CYLINDER............................6-9
RHD - INSTALLATION, PEDAL TORQUE
SHAFT..............................5-39
RHD - REMOVAL..............5-37,5-43,5-91
RHD - REMOVAL, MASTER CYLINDER......6-8
RHD - REMOVAL, PEDAL TORQUE
SHAFT..............................5-39
RHD GEAR - INSTALLATION............19-33
RHD GEAR - REMOVAL................19-31
RIGHT - CLEANING, EXHAUST
MANIFOLD..........................9-151
RIGHT - INSPECTION, EXHAUST
MANIFOLD...........................9-151
RIGHT - INSTALLATION, CYLINDER
HEAD COVER........................9-103
RIGHT - INSTALLATION, EXHAUST
MANIFOLD..........................9-151
RIGHT - REMOVAL, CYLINDER HEAD
COVER.............................9-102
RIGHT - REMOVAL, EXHAUST MANIFOLD . 9-150
RIGHT B-PILLAR SWITCH -
DESCRIPTION.......................8N-32
RIGHT B-PILLAR SWITCH -
INSTALLATION......................8N-32
RIGHT B-PILLAR SWITCH - OPERATION . . 8N-32
RIGHT B-PILLAR SWITCH - REMOVAL....8N-32
RIGHT D-PILLAR TRIM PANEL -
INSTALLATION.......................23-80
RIGHT D-PILLAR TRIM PANEL -
REMOVAL..........................23-80
RIGHT MOUNT - INSTALLATION.....9-135,9-51
RIGHT MOUNT - REMOVAL........9-135,9-51
RIGHT OUTBOARD - INSTALLATION,
SEAT BELT & RETRACTOR - SECOND
ROW ..............................8O-14
RIGHT OUTBOARD - REMOVAL, SEAT
BELT & RETRACTOR - SECOND ROW....8O-14
RIGHT OUTBOARD WITH REAR HVAC -
LWB - INSTALLATION, SEAT BELT &
RETRACTOR - SECOND ROW...........8O-15
RIGHT OUTBOARD WITH REAR HVAC -
LWB - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW...........8O-15
RIGHT QUARTER TRIM PANEL -
INSTALLATION.......................23-78
RIGHT QUARTER TRIM PANEL -
REMOVAL..........................23-78
RING, FITTING - PISTON
................9-45
RING FITTING - STANDARD
PROCEDURE, PISTON
.................9-121
RINGS - INSTALLATION, PISTON
........9-121
RINGS - REMOVAL, PISTON
............9-121
RISER - 50/50 SPLIT - INSTALLATION,
BENCH SEAT
........................23-99
RISER - 50/50 SPLIT - REMOVAL,
BENCH SEAT
........................23-99
RISER - INSTALLATION, LUGGAGE RACK
. . 23-55
RISER - INSTALLATION, QUAD BUCKET
SEAT
..............................23-96
RISER - MANUAL TRACK -
INSTALLATION, FRONT SEAT
...........23-93
RISER - MANUAL TRACK - REMOVAL,
FRONT SEAT
........................23-93
RISER - REMOVAL, LUGGAGE RACK
.....23-54
RISER - REMOVAL, QUAD BUCKET SEAT
. . 23-96
RISER - SECOND ROW - INSTALLATION,
BENCH SEAT
.......................23-100RISER - SECOND ROW - REMOVAL,
BENCH SEAT........................23-99
RISER - THIRD ROW - INSTALLATION,
BENCH SEAT.......................23-100
RISER - THIRD ROW - REMOVAL,
BENCH SEAT.......................23-100
RKE TRANSMITTER PROGRAMING -
STANDARD PROCEDURE..............8N-43
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-3
ROAD TEST - DIAGNOSIS AND TESTING . 21-119
ROCKER ARMS - DESCRIPTION.........9-109
ROCKER ARMS - INSPECTION...........9-35
ROCKER ARMS - INSTALLATION.........9-35
ROCKER ARMS - OPERATION...........9-109
ROCKER ARMS - REMOVAL.............9-34
ROCKER ARMS AND SHAFT - ASSEMBLY . 9-109
ROCKER ARMS AND SHAFT -
DISASSEMBLY.......................9-109
ROCKER ARMS AND SHAFT -
INSTALLATION.......................9-110
ROCKER ARMS AND SHAFT - REMOVAL . . 9-109
ROD - DESCRIPTION, LIFT GEAR & LINK . 8N-16
ROD - DESCRIPTION, PISTON &
CONNECTING....................9-116,9-42
ROD - INSTALLATION, LIFT GEAR &
LINK..............................8N-16
ROD - INSTALLATION, OUTER TIE.......19-34
ROD - INSTALLATION, PISTON &
CONNECTING.........................9-44
ROD - OPERATION, LIFT GEAR & LINK.....8N-16
ROD - REMOVAL, LIFT GEAR & LINK.....8N-16
ROD - REMOVAL, OUTER TIE...........19-34
ROD - REMOVAL, PISTON &
CONNECTING.........................9-43
ROD BEARING CLEARANCE - STANDARD
PROCEDURE, MEASURING
CONNECTING........................9-120
ROD, FITTING - CONNECTING............9-45
RODS - STANDARD PROCEDURE,
FITTING CONNECTING.................9-116
ROOF JOINT MOLDING - INSTALLATION . . 23-57
ROOF JOINT MOLDING - REMOVAL......23-57
ROTATION - STANDARD PROCEDURE,
TIRE AND WHEEL.....................22-7
ROTOR - DIAGNOSIS AND TESTING,
BRAKE..............................5-51
ROTOR - INSTALLATION, FRONT BRAKE . . . 5-54
ROTOR - REMOVAL, FRONT BRAKE.......5-54
ROTOR, EXPORT - BRAKE..............5-55
ROTOR MACHINING - STANDARD
PROCEDURE, BRAKE...................5-53
ROTOR, SPECIFICATIONS - BRAKE........5-55
ROW - BENCH - INSTALLATION, SEAT
BELT BUCKLE - FIRST................8O-12
ROW - BENCH - REMOVAL, SEAT BELT
BUCKLE - FIRST.....................8O-12
ROW - INSTALLATION, BENCH SEAT
RISER - SECOND
....................23-100
ROW - INSTALLATION, BENCH SEAT
RISER - THIRD
.....................23-100
ROW - LEFT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR - SECOND
...............8O-16
ROW - LEFT OUTBOARD - REMOVAL,
SEAT BELT & RETRACTOR - SECOND
....8O-16
ROW - OUTBOARD - INSTALLATION,
SEAT BELT & RETRACTOR - FIRST
......8O-13
ROW - OUTBOARD - REMOVAL, SEAT
BELT & RETRACTOR - FIRST
...........8O-13
ROW - REMOVAL, BENCH SEAT RISER -
SECOND
............................23-99
ROW - REMOVAL, BENCH SEAT RISER -
THIRD
............................23-100
ROW - RIGHT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR - SECOND
...............8O-14
ROW - RIGHT OUTBOARD - REMOVAL,
SEAT BELT & RETRACTOR - SECOND
....8O-14
ROW - RIGHT OUTBOARD WITH REAR
HVAC - LWB - INSTALLATION, SEAT
BELT & RETRACTOR - SECOND
.........8O-15
ROW - RIGHT OUTBOARD WITH REAR
HVAC - LWB - REMOVAL, SEAT BELT &
RETRACTOR - SECOND
...............8O-15
ROW - THREE PASSENGER BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND
...........................8O-14ROW - THREE PASSENGER BENCH -
REMOVAL, SEAT BELT BUCKLE -
SECOND...........................8O-14
ROW INBOARD - 50/50 BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND...........................8O-12
ROW INBOARD - 50/50 BENCH -
REMOVAL, SEAT BELT BUCKLE -
SECOND...........................8O-12
ROW INBOARD - QUAD BUCKET -
INSTALLATION, SEAT BELT BUCKLE -
FIRST.............................8O-11
ROW INBOARD - QUAD BUCKET -
REMOVAL, SEAT BELT BUCKLE - FIRST . . . 8O-11
RUN WEATHERSTRIP - INSTALLATION,
FRONT DOOR GLASS................23-110
RUN WEATHERSTRIP - REMOVAL,
FRONT DOOR GLASS................23-110
RUNOUT - DIAGNOSIS AND TESTING,
CLUTCH COVER AND DISC...............6-6
RUNOUT, SPECIFICATIONS - TONE
WHEEL.............................5-79
SAFETY CERTIFICATION LABEL -
DESCRIPTION, VEHICLE.............Intro.-11
SAFETY PRECAUTIONS AND WARNINGS,
WARNING...........................23-1
SAFETY PRECAUTIONS, WARNING -
WINDSHIELD.......................23-105
SANDING/BUFFING & POLISHING -
DESCRIPTION, FINESSE...............23-84
SBEC CONTROLLER - INSTALLATION.....8E-17
SBEC CONTROLLER - OPERATION,
8-VOLT SUPPLY - PCM OUTPUT.........8E-15
SBEC CONTROLLER - REMOVAL.........8E-16
SCHEDULES - DESCRIPTION,
MAINTENANCE........................0-7
SCHEMATICS AND DIAGRAMS - 41TE
TRANSAXLE HYDRAULIC SCHEMATICS . . 21-169
SCHEMATICS, SCHEMATICS AND
DIAGRAMS - 41TE TRANSAXLE
HYDRAULIC........................21-169
SCREEN - DESCRIPTION, VIDEO........8A-16
SCREEN - INSTALLATION, VIDEO........8A-16
SCREEN - OPERATION, VIDEO..........8A-16
SCREEN - REMOVAL, VIDEO............8A-16
SCUFF PAD - INSTALLATION, REAR
FASCIA..............................13-4
SCUFF PAD - REMOVAL, REAR FASCIA....13-3
SDP POWER TRANSFER UNIT, SPECIAL
TOOLS..............................21-8
SEAL - ASSEMBLY, CALIPER PISTON . . 5-26,5-29
SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP TO FILLER NECK.........7-27
SEAL - DISASSEMBLY, CALIPER PISTON . . . 5-24,
5-28
SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL................9-127,9-40
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL................9-127,9-40
SEAL - INSTALLATION, DIFFERENTIAL
CARRIER............................21-9
SEAL - INSTALLATION, END COVER......21-11
SEAL - INSTALLATION, HALF SHAFT
INNER.............................21-12
SEAL - INSTALLATION, INPUT FLANGE....3-45
SEAL - INSTALLATION, INPUT SHAFT.....21-18
SEAL - INSTALLATION, INPUT SHAFT
COVER.............................21-14
SEAL - INSTALLATION, INPUT SHAFT
END ...............................21-16
SEAL - INSTALLATION, OUTER HALF
SHAFT.............................21-19
SEAL - INSTALLATION, OUTPUT FLANGE . . . 3-46
SEAL - OIL PUMP - INSTALLATION.....21-233
SEAL - OIL PUMP - REMOVAL.........21-232
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL................9-129,9-42
SEAL - REAR - REMOVAL, CRANKSHAFT
OIL ...........................9-128,9-41
SEAL - REMOVAL, DIFFERENTIAL
CARRIER............................21-9
SEAL - REMOVAL, END COVER..........21-11
SEAL - REMOVAL, HALF SHAFT INNER . . . 21-12
SEAL - REMOVAL, INPUT FLANGE
........3-44
SEAL - REMOVAL, INPUT SHAFT
........21-17
SEAL - REMOVAL, INPUT SHAFT COVER
. . 21-13
SEAL - REMOVAL, INPUT SHAFT END
....21-15
SEAL - REMOVAL, OUTER HALF SHAFT
. . . 21-19
RSINDEX27
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com