2003 CHRYSLER CARAVAN battery location

INSTALLATION
INSTALLATION- HEATER CORE EXTENSION
TUBES
WARNING: REFER TO THE APPLICABLE WARN-
INGS AND CAUTIONS FOR THIS SYSTEM BEFORE
PERFORMING THE FOLLOWING OPERATION.
(Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING FRONT - WARNING - HEATER PLUMB-
ING).
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFOREATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
(1) Remove the plugs or tape from both heater core
tube fittings and both heater core ports.
(2) Position the heater core tubes and sealing plate
as a unit beneath the instrument panel.
(3) Align the engine compartment ends of both
heater core tubes with the openings in the dash
panel seal and push them simultaneously forward
through the seal far enough to engage the heater
core ends of the tubes with the heater core supply
and return ports.
(4) Position both heater core tubes and the sealing
plate simultaneously to the heater core supply and
return ports.
(5) The heater core tubes each have a slot that
must be indexed to a location tab within each of the
heater core ports. Adjust the position of the tubes as
required so that the sealing plate fits flush against
the heater core supply and return ports, which indi-
cates that the tubes are properly indexed.
(6) Install and tighten the screw that secures the
heater core tube sealing plate to the heater core sup-
ply and return ports. Tighten the screw to 3 N´m (27
in. lbs.).
(7) Position the heater core shield onto the distri-
bution housing. Be certain that the two location tabs
Fig. 18 Heater Core
1 - SEALING PLATE
2 - SCREW
3 - SCREWS (2)
4 - HEATER CORE
5 - HEATER CORE TUBES
Fig. 19 Accelerator Pedal
1 - SLIDE HEATER CORE PAST ACCELERATOR PEDAL
Fig. 20 Brake Pedal
1 - SLIDE HEATER CORE PAST BRAKE PEDAL
2 - DEPRESS BRAKE PEDAL
RSPLUMBING - FRONT24-77
HEATER CORE (Continued)
ProCarManuals.com

on the front of the shield are engaged in the recepta-
cles in the two lower finger formations of the evapo-
rator housing near the dash panel.
(8) Install and tighten the three screws that secure
the heater core shield to the left end of the HVAC
distribution housing. Tighten the screws to 2 N´m (17
in. lbs.).
(9) Reinstall the silencer under the driver side end
of the instrument panel. (Refer to 23 - BODY/IN-
STRUMENT PANEL/INSTRUMENT PANEL
SILENCER - INSTALLATION).
(10) Reconnect the heater hoses to the heater hose
tubes. (Refer to 24 - HEATING & AIR CONDITION-
ING/PLUMBING - FRONT/HEATER HOSE -
INSTALLATION).
(11) Reconnect the battery negative cable.
(12) Refill the engine cooling system. (Refer to 7 -
COOLING - STANDARD PROCEDURE - COOLING
SYSTEM REFILL).
INSTALLATION - HEATER CORE
WARNING: REFER TO THE APPLICABLE WARN-
INGS AND CAUTIONS FOR THIS SYSTEM BEFORE
PERFORMING THE FOLLOWING OPERATION.
(Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING FRONT - WARNING - HEATER PLUMB-
ING).
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
(1) While pushing the brake pedal downward and
pulling the accelerator pedal upward far enough for
clearance, slide the heater core into the distribution
housing.
(2) Install and tighten the two screws that secure
the heater core mounting plate to the distribution
housing. Tighten the screws to 2 N´m (17 in. lbs.).
(3) Remove the plugs or tape from the heater core
tube fittings and both heater core ports.
(4) Position both heater core tubes and the sealing
plate simultaneously to the heater core supply and
return ports.(5) The heater core tubes each have a slot that
must be indexed to a location tab within each of the
heater core ports. Adjust the position of the tubes as
required so that the sealing plate fits flush against
the heater core supply and return ports, which indi-
cates that the tubes are properly indexed.
(6) Install and tighten the screw that secures the
heater core tube sealing plate to the heater core sup-
ply and return ports. Tighten the screw to 3 N´m (27
in. lbs.).
(7) Position the heater core shield onto the distri-
bution housing. Be certain that the two location tabs
on the front of the shield are engaged in the recepta-
cles in the two lower finger formations of the evapo-
rator housing near the dash panel.
(8) Install and tighten the three screws that secure
the heater core shield to the left end of the HVAC
distribution housing. Tighten the screws to 2 N´m (17
in. lbs.).
(9) Reconnect the power brake booster input rod
(push rod) to the pin on the brake pedal arm(Refer to
5 - BRAKES/HYDRAULIC/MECHANICAL/POWER
BRAKE BOOSTER - INSTALLATION).
(10) Reinstall the brake lamp switch into its
mounting bracket(Refer to 8 - ELECTRICAL/LAMPS/
LIGHTING - EXTERIOR/BRAKE LAMP SWITCH -
INSTALLATION).
(11) Reinstall the silencer boot around the base of
the lower steering shaft on the dash panel.
(12) Reconnect the battery negative cable.
(13) Refill the engine cooling system. (Refer to 7 -
COOLING - STANDARD PROCEDURE - COOLING
SYSTEM REFILL).
(14) Operate system for two thermostat cycles to
assure elimination of air in the system.
HEATER HOSE
REMOVAL
There are several heater core plumbing configura-
tions used on this model, depending upon the engine
size and other optional equipment. One plumbing
configuration is used for all 2.4L engines (Fig. 21),
while the 3.3L and 3.8L engines have unique heater
return plumbing on the engine for models with or
without an optional engine oil cooler (Fig. 24) or (Fig.
25). There are also unique plumbing configurations
at the heater core for models with or without the
optional rear heater and air conditioner (Fig. 22) or
(Fig. 23). All models use a combination of formed
steel tubing and rubber hoses. In most cases, the
rubber hose is secured to the steel tubing with a
spring tension clamp.
24 - 78 PLUMBING - FRONTRS
HEATER CORE (Continued)
ProCarManuals.com

NATURAL VAC LEAK
DETECTION ASSY
REMOVAL
(1) Disconnect thew negative battery cable.
(2) Raise vehicle and support (Fig. 4).
(3) Unlock and disconnect the electrical connector.
(4) Remove the hoses from the NVLD valve.
(5) Remove the 2 fasteners.
(6) Remove the valve and bracket from vehicle
(Fig. 5).
(7) Remove valve from bracket (Fig. 6).
INSTALLATION
(1) Install NVLD valve to the bracket (Fig. 6).
(2) Install valve and bracket to the vehicle (Fig. 5).
(3) Install the 2 mounting bolts and tighten.
(4) Install the electrical connector and lock.
(5) Install the 2 hoses and lock the clamps.
(6) Lower vehicle.
LEAK DETECTION PUMP
REMOVAL
(1) Disconnect the negative battery cable.
(2) Raise and support the vehicle.
(3) Remove 3 hoses (Fig. 7).
(4) Remove the electrical connector (Fig. 8).
(5) Remove the 3 screws and remove LDP pump.
INSTALLATION
(1) Install LDP.
(2) Install the 3 screws and tighten (Fig. 8).
(3) Install the electrical connector.
(4) Install the 3 hoses (Fig. 7).
(5) Lower vehicle.
(6) Connect the negative battery cable.
Fig. 4 NVLD LOCATION
Fig. 5 NVLD REMOVAL/INSTALLATION
Fig. 6 NVLD VALVE AND BRACKET
RSEVAPORATIVE EMISSIONS25-13
ProCarManuals.com

COLUMN COVER BACKING PLATE -
REMOVAL, STEERING.................23-69
COLUMN TORQUE, SPECIFICATIONS.....19-14
COMBUSTION PRESSURE LEAKAGE
TEST - DIAGNOSIS AND TESTING,
CYLINDER........................9-83,9-9
COMMON PROBLEM CAUSES -
DIAGNOSIS AND TESTING.............21-30
COMMUNICATION RECEIVE - PCM INPUT
- OPERATION, DATA BUS..............8E-15
COMMUNICATIONS INTERFACE (PCI)
BUS, OPERATION - PROGRAMMABLE....14-21
COMPASS CALIBRATION - STANDARD
PROCEDURE.........................8M-3
COMPASS DEMAGNETIZING -
STANDARD PROCEDURE...............8M-4
COMPASS MINI-TRIP COMPUTER -
DIAGNOSIS AND TESTING.............8M-10
COMPASS VARIATION ADJUSTMENT -
STANDARD PROCEDURE...............8M-5
COMPASS/MINI-TRIP COMPUTER -
DESCRIPTION........................8M-9
COMPASS/MINI-TRIP COMPUTER -
INSTALLATION......................8M-10
COMPASS/MINI-TRIP COMPUTER -
OPERATION.........................8M-9
COMPASS/MINI-TRIP COMPUTER -
REMOVAL..........................8M-10
COMPLAINTS - DIAGNOSIS AND
TESTING, CLUTCH CHATTER..............6-6
COMPRESSION PRESSURE TEST -
DIAGNOSIS AND TESTING, CYLINDER . . 9-83,9-9
COMPRESSOR - 2.4/3.3/3.8L ENGINES -
REMOVAL............................24-64
COMPRESSOR - DESCRIPTION, A/C......24-63
COMPRESSOR - INSTALLATION.........24-65
COMPRESSOR - OPERATION, A/C........24-63
COMPRESSOR CLUTCH - DESCRIPTION . . 24-16
COMPRESSOR CLUTCH - OPERATION....24-17
COMPRESSOR CLUTCH AIR GAP -
STANDARD PROCEDURE...............24-17
COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE...............24-17
COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-20
COMPRESSOR CLUTCH RELAY -
DESCRIPTION.......................24-21
COMPRESSOR CLUTCH RELAY -
DIAGNOSIS AND TESTING.............24-22
COMPRESSOR CLUTCH RELAY -
INSTALLATION.......................24-22
COMPRESSOR CLUTCH RELAY -
OPERATION.........................24-21
COMPRESSOR CLUTCH RELAY -
REMOVAL..........................24-22
COMPRESSOR CLUTCH/COIL -
INSPECTION........................24-18
COMPRESSOR MOUNTING BRACKET -
2.4L ENGINE - INSTALLATION...........24-66
COMPRESSOR MOUNTING BRACKET -
2.4L ENGINE - REMOVAL..............24-65
COMPRESSOR NOISE DIAGNOSIS -
DIAGNOSIS AND TESTING.............24-63
COMPUTER - DESCRIPTION, COMPASS/
MINI-TRIP..........................8M-9
COMPUTER - DIAGNOSIS AND TESTING,
COMPASS MINI-TRIP
.................8M-10
COMPUTER - INSTALLATION, COMPASS/
MINI-TRIP
.........................8M-10
COMPUTER - OPERATION, COMPASS/
MINI-TRIP
..........................8M-9
COMPUTER - REMOVAL, COMPASS/
MINI-TRIP
.........................8M-10
CONCENTRATION TESTING - DIAGNOSIS
AND TESTING, COOLANT
...............7-19
CONDENSER - DESCRIPTION
...........24-66
CONDENSER - INSTALLATION
...........24-67
CONDENSER - OPERATION
.............24-66
CONDENSER - REMOVAL
..............24-66
CONDITION CHECK, STANDARD
PROCEDURE - FLUID LEVEL
...........21-201
CONDITIONING LINES - INSTALLATION,
REAR AIR
.........................24-105
CONDITIONING LINES - REMOVAL, REAR
AIR
..............................24-104
CONNECTING ROD - DESCRIPTION,
PISTON
........................9-116,9-42CONNECTING ROD - INSTALLATION,
PISTON.............................9-44
CONNECTING ROD - REMOVAL, PISTON . . . 9-43
CONNECTING ROD BEARING
CLEARANCE - STANDARD
PROCEDURE, MEASURING.............9-120
CONNECTING ROD, FITTING.............9-45
CONNECTING RODS - STANDARD
PROCEDURE, FITTING.................9-116
CONNECTOR - DESCRIPTION, DATA LINK . . 8E-6
CONNECTOR - INSTALLATION.......8W-01-11
CONNECTOR - OPERATION, DATA LINK....8E-7
CONNECTOR - REMOVAL...........8W-01-11
CONNECTOR, GROUND AND SPLICE
INFORMATION - DESCRIPTION........8W-01-7
CONNECTOR/GROUND/SPLICE LOCATION
- DESCRIPTION....................8W-91-1
CONSOLE - DESCRIPTION, OVERHEAD....8M-1
CONSOLE - DIAGNOSIS AND TESTING,
OVERHEAD..........................8M-2
CONSOLE - INSTALLATION, LOWER......23-68
CONSOLE - OPERATION, OVERHEAD......8M-2
CONSOLE - REMOVAL, LOWER..........23-68
CONSOLE - REMOVAL, OVERHEAD.......8M-6
CONSOLE LAMP SWITCH -
INSTALLATION, CENTER...............8L-26
CONSOLE LAMP SWITCH - REMOVAL,
CENTER............................8L-26
CONSOLE, SPECIAL TOOLS - OVERHEAD . . 8M-6
CONSOLE TRAY - BRACKET ASSEMBLY -
INSTALLATION, FLOOR................23-82
CONSOLE TRAY - BRACKET ASSEMBLY -
REMOVAL, FLOOR....................23-82
CONSOLE TRAY - INSTALLATION, FLOOR . . 23-81
CONSOLE TRAY - REMOVAL, FLOOR.....23-81
CONTAINER - DESCRIPTION, COOLANT
RECOVERY..........................7-19
CONTAINER - INSTALLATION, COOLANT
RECOVERY..........................7-20
CONTAINER - OPERATION, COOLANT
RECOVERY..........................7-19
CONTAINER - REMOVAL, COOLANT
RECOVERY..........................7-20
CONTAMINATION - DIAGNOSIS AND
TESTING, BRAKE FLUID................5-32
CONTINUITY - STANDARD PROCEDURE,
TESTING.........................8W-01-9
CONTROL (4 SPEED EATX ONLY) -
OPERATION, INTERACTIVE SPEED........8P-2
CONTROL ARM - DESCRIPTION, LOWER . . . 2-12
CONTROL ARM - INSPECTION, LOWER....2-14
CONTROL ARM - INSTALLATION, LOWER . . 2-15
CONTROL ARM - OPERATION, LOWER.....2-12
CONTROL ARM - REMOVAL, LOWER......2-12
CONTROL ARM (REAR BUSHING -
HYDRO) - ASSEMBLY, LOWER...........2-14
CONTROL ARM (REAR BUSHING -
HYDRO) - DISASSEMBLY, LOWER........2-14
CONTROL ARM (REAR BUSHING -
STANDARD) - ASSEMBLY, LOWER........2-14
CONTROL ARM (REAR BUSHING -
STANDARD) - DISASSEMBLY, LOWER.....2-13
CONTROL CABLE - INSTALLATION,
THROTTLE..........................14-35
CONTROL CABLE - REMOVAL,
THROTTLE..........................14-35
CONTROL CALIBRATION - STANDARD
PROCEDURE, HEATER-A/C..............24-8
CONTROL CIRCUIT TEST - DIAGNOSIS
AND TESTING.......................8F-30
CONTROL INFORMATION LABEL -
DESCRIPTION, VEHICLE EMISSION.......25-1
CONTROL MODULE - DESCRIPTION,
BODY...............................8E-3
CONTROL MODULE - DESCRIPTION,
FRONT..............................8E-7
CONTROL MODULE - DESCRIPTION,
POWER LIFTGATE....................8E-10
CONTROL MODULE - DESCRIPTION,
SIDE IMPACT AIRBAG
.................8O-17
CONTROL MODULE - DESCRIPTION,
SLIDING DOOR
......................8E-19
CONTROL MODULE - DESCRIPTION,
TRANSMISSION
......................8E-20
CONTROL MODULE - DIAGNOSIS AND
TESTING, FRONT
......................8E-7
CONTROL MODULE - INSTALLATION,
BODY
...............................8E-5CONTROL MODULE - INSTALLATION,
FRONT..............................8E-8
CONTROL MODULE - INSTALLATION,
POWER LIFTGATE....................8E-11
CONTROL MODULE - INSTALLATION,
SIDE IMPACT AIRBAG.................8O-17
CONTROL MODULE - INSTALLATION,
SLIDING DOOR......................8E-20
CONTROL MODULE - OPERATION, BODY . . . 8E-3
CONTROL MODULE - OPERATION,
FRONT..............................8E-7
CONTROL MODULE - OPERATION,
POWER LIFTGATE....................8E-11
CONTROL MODULE - OPERATION, SIDE
IMPACT AIRBAG.....................8O-17
CONTROL MODULE - OPERATION,
SLIDING DOOR......................8E-19
CONTROL MODULE - OPERATION,
TRANSMISSION......................8E-20
CONTROL MODULE - REMOVAL, BODY....8E-4
CONTROL MODULE - REMOVAL, FRONT . . . 8E-8
CONTROL MODULE - REMOVAL, POWER
LIFTGATE...........................8E-11
CONTROL MODULE - REMOVAL, SIDE
IMPACT AIRBAG.....................8O-17
CONTROL MODULE - REMOVAL,
SLIDING DOOR......................8E-19
CONTROL MOTOR - DESCRIPTION, IDLE
AIR ...............................14-28
CONTROL MOTOR - INSTALLATION, IDLE
AIR ...............................14-29
CONTROL MOTOR - OPERATION, IDLE
AIR.................................14-28
CONTROL MOTOR - REMOVAL, IDLE AIR . . 14-29
CONTROL RELAY - DESCRIPTION,
TRANSMISSION.....................21-247
CONTROL RELAY - OPERATION,
TRANSMISSION.....................21-248
CONTROL SWITCH - DIAGNOSIS AND
TESTING, TRACTION...................5-82
CONTROL SYSTEM - DESCRIPTION,
TRACTION...........................5-76
CONTROL SYSTEM - OPERATION,
EVAPORATION.......................25-10
CONTROL SYSTEM - OPERATION,
TRACTION...........................5-77
CONTROLLER - DESCRIPTION,
OCCUPANT RESTRAINT................8O-7
CONTROLLER - INSTALLATION,
OCCUPANT RESTRAINT................8O-7
CONTROLLER - INSTALLATION, SBEC....8E-17
CONTROLLER - OPERATION, 8-VOLT
SUPPLY - PCM OUTPUT - SBEC.........8E-15
CONTROLLER - OPERATION, OCCUPANT
RESTRAINT..........................8O-7
CONTROLLER - REMOVAL, NGC.........8E-17
CONTROLLER - REMOVAL, OCCUPANT
RESTRAINT..........................8O-7
CONTROLLER - REMOVAL, SBEC........8E-16
CONTROLLER ANTILOCK BRAKE -
DESCRIPTION........................8E-5
CONTROLLER ANTILOCK BRAKE -
INSTALLATION........................8E-6
CONTROLLER ANTILOCK BRAKE -
OPERATION..........................8E-5
CONTROLLER ANTILOCK BRAKE -
REMOVAL...........................8E-6
CONVENTIONAL BATTERY CHARGING -
STANDARD PROCEDURE...............8F-11
CONVERTER - DESCRIPTION, CATALYTIC . . . 11-4
CONVERTER - DESCRIPTION, TORQUE . . . 21-242
CONVERTER - INSPECTION, CATALYTIC....11-5
CONVERTER - INSTALLATION, CATALYTIC . . 11-6
CONVERTER - INSTALLATION, TORQUE . . 21-247
CONVERTER - OPERATION, CATALYTIC....11-4
CONVERTER - OPERATION, TORQUE....21-245
CONVERTER - REMOVAL, CATALYTIC......11-5
CONVERTER - REMOVAL, TORQUE......21-247
CONVERTER HOUSING FLUID LEAKAGE -
DIAGNOSIS AND TESTING, TORQUE.....21-123
COOL DOWN TEST - DIAGNOSIS AND
TESTING, A/C
........................24-4
COOLANT - DESCRIPTION, ENGINE
.......7-19
COOLANT - DESCRIPTION, ENGINE
........0-3
COOLANT - STANDARD PROCEDURE,
ADDING ADDITIONAL
...................7-5
COOLANT CONCENTRATION TESTING -
DIAGNOSIS AND TESTING
..............7-19
RSINDEX7
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

SPEED SENSOR - INSTALLATION,
VEHICLE..........................21-115
SPEED SENSOR - OPERATION, ENGINE . . . 14-26
SPEED SENSOR - OUTPUT -
DESCRIPTION......................21-241
SPEED SENSOR - OUTPUT -
INSTALLATION......................21-242
SPEED SENSOR - OUTPUT - OPERATION . 21-241
SPEED SENSOR - OUTPUT - REMOVAL . . 21-241
SPEED SENSOR - REMOVAL, FRONT
WHEEL.............................5-79
SPEED SENSOR - REMOVAL, VEHICLE . . . 21-115
SPEED SENSOR AIR GAP,
SPECIFICATIONS - WHEEL..............5-79
SPIRAL PLATE BATTERY CHARGING -
STANDARD PROCEDURE...............8F-10
SPLASH SHIELD - INSTALLATION,
FRONT WHEELHOUSE.................23-54
SPLASH SHIELD - REMOVAL, FRONT
WHEELHOUSE.......................23-54
SPLICE INFORMATION - DESCRIPTION,
CONNECTOR, GROUND..............8W-01-7
SPLICING - STANDARD PROCEDURE,
WIRE...........................8W-01-15
SPLIT - INSTALLATION, BENCH SEAT
RISER - 50/50.......................23-99
SPLIT - REMOVAL, BENCH SEAT RISER -
50/50..............................23-99
SPLIT, BENCH - INSTALLATION, SEAT
BACK HINGE COVERS - QUAD BUCKET,
50/50.............................23-100
SPLIT, BENCH - INSTALLATION, SEAT
CUSHION COVER - QUAD BUCKET,
50/50..............................23-99
SPLIT, BENCH - REMOVAL, SEAT BACK
HINGE COVERS - QUAD BUCKET, 50/50 . . 23-100
SPLIT, BENCH - REMOVAL, SEAT
CUSHION COVER - QUAD BUCKET,
50/50..............................23-98
SPOILER - INSTALLATION, LIFTGATE.....23-41
SPOILER - REMOVAL, LIFTGATE.........23-41
SPRING - DESCRIPTION, CLOCK.........8O-4
SPRING - INSTALLATION, CLOCK.........8O-5
SPRING - OPERATION, CLOCK...........8O-4
SPRING - REMOVAL, CLOCK............8O-4
SPRING CENTERING - STANDARD
PROCEDURE, CLOCK..................8O-4
SPRING FRONT BUSHING -
INSTALLATION, LEAF...................2-29
SPRING FRONT BUSHING - REMOVAL,
LEAF...............................2-28
SPRING MOUNTS - FRONT -
INSTALLATION........................2-42
SPRING MOUNTS - FRONT - REMOVAL....2-42
SPRING MOUNTS - REAR -
INSTALLATION........................2-43
SPRING MOUNTS - REAR - REMOVAL.....2-43
SPRINGS - DESCRIPTION, VALVE........9-106
SPRINGS - OPERATION, VALVE.........9-106
SPROCKET - INSTALLATION,
CRANKSHAFT...................9-156,9-65
SPROCKET - INSTALLATION, TIMING
CHAIN AND CAMSHAFT...............9-157
SPROCKET - REMOVAL, CRANKSHAFT . . . 9-156,
9-64
SPROCKET - REMOVAL, TIMING CHAIN
AND CAMSHAFT.....................9-156
SPROCKETS - INSTALLATION,
CAMSHAFT..........................9-65
SPROCKETS - REMOVAL, CAMSHAFT......9-64
STABILIZER - INSTALLATION...........23-32
STABILIZER - REMOVAL...............23-32
STABILIZER BAR - DESCRIPTION.....2-16,2-43
STABILIZER BAR - INSPECTION..........2-17
STABILIZER BAR - INSTALLATION........2-17
STABILIZER BAR - OPERATION.......2-16,2-44
STABILIZER BAR - REMOVAL............2-17
STABILIZER BAR CUSHION -
INSTALLATION.........................2-4
STABILIZER BAR CUSHION - REMOVAL.....2-4
STABILIZER SOCKET - INSTALLATION....23-32
STABILIZER SOCKET - REMOVAL........23-32
STAKING - STANDARD PROCEDURE,
HEAT
..............................23-10
STANDARD 4 CYLINDER - DESCRIPTION
. . . 8I-9
STARTER, SPECIFICATIONS
.............8F-34
STARTING - DESCRIPTION
.............8F-28
STARTING - OPERATION
...............8F-28STARTING - STANDARD PROCEDURE,
JUMP...............................0-15
STARTING SYSTEM TEST - DIAGNOSIS
AND TESTING.......................8F-28
STATE DISPLAY TEST MODE,
OPERATION - DRB IIIT.................25-9
STEERING - DIAGNOSIS AND TESTING,
SUSPENSION.........................2-49
STEERING BELT TENSION - STANDARD
PROCEDURE, CHECKING POWER..........7-8
STEERING COLUMN - DESCRIPTION.....19-10
STEERING COLUMN - DIAGNOSIS AND
TESTING...........................19-12
STEERING COLUMN COVER -
INSTALLATION, LOWER................23-69
STEERING COLUMN COVER -
INSTALLATION, OVER.................23-69
STEERING COLUMN COVER - REMOVAL,
LOWER............................23-69
STEERING COLUMN COVER - REMOVAL,
OVER..............................23-69
STEERING COLUMN COVER BACKING
PLATE - INSTALLATION................23-69
STEERING COLUMN COVER BACKING
PLATE - REMOVAL...................23-69
STEERING FASTENER TORQUE,
SPECIFICATIONS - POWER..............19-9
STEERING FLUID LEVEL CHECKING -
STANDARD PROCEDURE, POWER.......19-44
STEERING GEAR, SPECIAL TOOLS -
POWER............................19-34
STEERING KNUCKLE - INSPECTION........2-9
STEERING KNUCKLE - INSTALLATION........2-9
STEERING KNUCKLE - REMOVAL..........2-7
STEERING PUMP INITIAL OPERATION -
STANDARD PROCEDURE, POWER.......19-37
STEERING PUMP, SPECIAL TOOLS -
POWER............................19-43
STEERING, SPECIAL TOOLS - POWER.....19-9
STEERING SYSTEM - DESCRIPTION,
POWER.............................19-1
STEERING SYSTEM - OPERATION,
POWER.............................19-1
STEERING SYSTEM DIAGNOSIS CHARTS
- DIAGNOSIS AND TESTING.............19-3
STEERING SYSTEM FLOW AND
PRESSURE TEST - DIAGNOSIS AND
TESTING, POWER.....................19-1
STEERING WHEEL - INSTALLATION......19-24
STEERING WHEEL - REMOVAL..........19-23
STEM SEALS - DESCRIPTION, VALVE.....9-111
STEM SEALS - INSTALLATION, VALVE....9-112
STEM SEALS - REMOVAL, VALVE........9-112
STOP BUMPER - INSTALLATION.........23-25
STOP BUMPER - REMOVAL............23-25
STOP BUMPER BEZEL - INSTALLATION,
SLIDING DOOR......................23-25
STOP BUMPER BEZEL - REMOVAL,
SLIDING DOOR......................23-25
STOP LAMP - INSTALLATION, CENTER
HIGH MOUNTED......................8L-6
STOP LAMP - REMOVAL, CENTER HIGH
MOUNTED...........................8L-6
STOP LAMP UNIT - INSTALLATION,
CENTER HIGH MOUNTED...............8L-7
STOP LAMP UNIT - REMOVAL, CENTER
HIGH MOUNTED
......................8L-6
STORAGE BIN - INSTALLATION, UNDER
SEAT
.............................23-103
STORAGE BIN - REMOVAL, UNDER SEAT
. 23-103
STORAGE BIN GUIDE - INSTALLATION,
UNDER SEAT
.......................23-104
STORAGE BIN GUIDE - REMOVAL,
UNDER SEAT
.......................23-104
STORAGE BIN LOCK/LATCH -
INSTALLATION, UNDER SEAT
..........23-104
STORAGE BIN LOCK/LATCH - REMOVAL,
UNDER SEAT
.......................23-104
STRAP - INSTALLATION, CHECK
.........23-15
STRAP - INSTALLATION, FRONT
SEATBACK ASSIST
...................23-91
STRAP - REMOVAL, CHECK
............23-15
STRAP - REMOVAL, FRONT SEATBACK
ASSIST
............................23-91
STRIKER - INSTALLATION, CENTER
......23-27
STRIKER - INSTALLATION, FUEL FILL
DOOR BLOCKER LATCH
...............23-52STRIKER - INSTALLATION, GLOVE BOX
LATCH .............................23-64
STRIKER - INSTALLATION, HOLD OPEN
LATCH .............................23-26
STRIKER - INSTALLATION, LATCH . . 23-19,23-40,
23-61
STRIKER - INSTALLATION, REAR LATCH . . 23-28
STRIKER - REMOVAL, CENTER..........23-27
STRIKER - REMOVAL, FUEL FILL DOOR
BLOCKER LATCH.....................23-52
STRIKER - REMOVAL, GLOVE BOX
LATCH .............................23-64
STRIKER - REMOVAL, HOLD OPEN
LATCH .............................23-26
STRIKER - REMOVAL, LATCH . 23-19,23-40,23-61
STRIKER - REMOVAL, REAR LATCH......23-28
STRIPPED THREAD REPAIR - STANDARD
PROCEDURE, MANIFOLD..............9-145
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS....................23-153
STRUCTURAL COLLAR - INSTALLATION....9-48
STRUCTURAL COLLAR - REMOVAL.......9-47
STRUT ASSEMBLY - ASSEMBLY..........2-23
STRUT ASSEMBLY - DESCRIPTION.......2-19
STRUT ASSEMBLY - DIAGNOSIS AND
TESTING............................2-20
STRUT ASSEMBLY - DISASSEMBLY.......2-21
STRUT ASSEMBLY - INSTALLATION.......2-25
STRUT ASSEMBLY - OPERATION.........2-19
STRUT ASSEMBLY - REMOVAL............2-20
STUDS - FRONT - INSTALLATION,
WHEEL MOUNTING...................22-21
STUDS - FRONT - REMOVAL, WHEEL
MOUNTING.........................22-20
STUDS - REAR - INSTALLATION, WHEEL
MOUNTING.........................22-22
STUDS - REAR - REMOVAL, WHEEL
MOUNTING.........................22-21
SUCTION LINE - INSTALLATION . . . 24-102,24-91
SUCTION LINE - REMOVAL.......24-101,24-90
SUN VISOR - INSTALLATION...........23-81
SUN VISOR - REMOVAL...............23-81
SUN VISOR SUPPORT - INSTALLATION . . . 23-81
SUN VISOR SUPPORT - REMOVAL.......23-81
SUNROOF - DESCRIPTION............23-113
SUNROOF - DIAGNOSIS AND TESTING . . . 23-113
SUNROOF ASSEMBLY - INSTALLATION . . 23-117
SUNROOF ASSEMBLY - REMOVAL......23-117
SUNROOF GLASS PANEL ADJUSTMENT,
ADJUSTMENTS.....................23-117
SUNROOF MOTOR - INSTALLATION.....23-118
SUNROOF MOTOR - REMOVAL.........23-118
SUNROOF SWITCH - INSTALLATION.....23-120
SUNROOF SWITCH - REMOVAL........23-120
SUNSHADE - INSTALLATION...........23-118
SUNSHADE - REMOVAL..............23-117
SUPPLEMENTAL DIESEL HEATER
WIRING - INSTALLATION.............24-112
SUPPLEMENTAL DIESEL HEATER
WIRING - REMOVAL.................24-112
SUPPLEMENTAL HEATER - DCHA -
DIAGNOSIS AND TESTING, DIESEL......24-107
SUPPLEMENTAL HEATER - DCHA -
EXPORT - DESCRIPTION, DIESEL.......24-106
SUPPLY - PCM OUTPUT - OPERATION, 5
VOLT ..............................8E-15
SUPPLY - PCM OUTPUT - SBEC
CONTROLLER - OPERATION, 8-VOLT.....8E-15
SUPPORT - INSTALLATION, LUMBAR....23-104
SUPPORT - INSTALLATION, SUN VISOR . . . 23-81
SUPPORT - REMOVAL, LUMBAR.......23-104
SUPPORT - REMOVAL, SUN VISOR......23-81
SUPPORT CYLINDER - INSTALLATION....23-42
SUPPORT CYLINDER - REMOVAL........23-42
SUPPORT PLATE - DRUM BRAKE -
INSTALLATION........................5-56
SUPPORT PLATE - DRUM BRAKE -
REMOVAL...........................5-56
SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO NOISE...........8A-11
SUPPRESSION COMPONENTS -
OPERATION, RADIO NOISE.............8A-12
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
.......9-11,9-85
SUSPENSION - DESCRIPTION, FRONT
......2-2
SUSPENSION - DESCRIPTION, REAR
......2-26
SUSPENSION - OPERATION, FRONT
........2-2
SUSPENSION - OPERATION, REAR
........2-26
RSINDEX31
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com