2003 CHEVROLET C/K light

2-91 Exhaust Brake Indicator Light
(If Equipped)
If your vehicle is equipped
with an exhaust brake, you
will have this light, located
above the comfort controls
in the center of the
instrument panel.
The exhaust brake indicator light will come on and stay
on whenever the diesel engine exhaust brake or exhaust
restrictor is active. For more information, see ªDiesel
Engine Exhaust Brakeº in the Index.
Diff Lock Indicator Light (If Equipped)
This light located in the
center of the instrument
panel is on when the
inter
-axle differential
lock system is in use.
The light will come on momentarily during starting.
If the light fails to come on, have it repaired as soon
as possible so you will be aware when the lock system
is in use.

2-92 Daytime Running Lamps (DRL)
Indicator Light
This light is located on the
instrument panel cluster. It
goes on whenever the
Daytime Running Lamps
are on.
See ªDaytime Running Lampsº in the Index.
When it begins to get dark, the DRL indicator light is a
reminder to turn on your headlamps.
Low Washer Fluid Warning Light
This light will come on
when your vehicle is low on
windshield washer fluid.
For more information, see ªWindshield Washer Fluidº in
the Index.
Check Gages Indicator Light
This light will come on as
you're starting the engine,
just as a check.
If it ever comes on and stays on while you are driving,
however, it means that either your engine coolant
temperature gage or your engine oil pressure gage may
be showing a reading in the warning zone.
When the check gages light comes on, you will also hear
a warning tone. The tone and the light will stay activated
until the problem is corrected.
This light may also come on if your vehicle is equipped
with the optional automatic engine shutdown system and
engine shutdown has begun. See ªEngine Automatic
Shutdownº in the Index.

2-93 Fuel Gage
Your fuel gage is located on
the right side of your
instrument panel cluster.
When the ignition is on, your fuel gage lets you know
about how much fuel you have left. When the gage first
shows empty, you'll still have a little fuel left, but you
should get more fuel soon.
If your vehicle has dual fuel tanks, the reading on the
gage is the total fuel left in both tanks.
Here are four concerns of some operators. None of these
shows a problem with your fuel gage:

The gage moves a little when you turn a corner or
speed up.
The gage doesn't go back to empty when you turn
off the ignition.

At the gas station, the pump shuts off before the gage
reads full.

It takes a little more or less fuel to fill up than the
gage indicated.
If you have a diesel engine, also see your Caterpillar

Operation & Maintenance Manual.
Water in Fuel Warning Light (If Equipped)
If your vehicle is equipped
with a diesel engine, you
may have this light
This light will come on to warn you that there is water
in the fuel system. For more information on how this
light works, see ªDiesel Fuel Requirements and Fuel
Systemº in the Index.

2-94 Air Pressure Gage (If Equipped)
If your vehicle has air
brakes, the air pressure gage
is located above the
switchbank in the center of
the instrument panel.
This gage shows the air pressure for both your front and
rear brake systems.
If the needle on the gage indicates that the air pressure is
below 60 to 75 psi (415 to 517 kPa), the low air warning
light will come on. An alarm will also sound if this
happens.
The yellow pointer shows the pressure available for the
front system, while the green pointer shows pressure for
the rear. There should be no more than 4 psi (28 kPa)
difference showing between the systems.
Don't drive until both pointers are showing at least
115 psi (793 kPa), so you'll have enough air if you
need to apply your brakes.
Air Filter Restriction Indicator (Option)
This optional gage is
located above the
switchbank in the center
of the instrument panel.
It monitors the engine
air filter.
As the filter gets dirty, the yellow indicator will begin to
rise. When it reaches 25 inches of vacuum on the scale,
the filter should be replaced.
After replacing the filter, reset the gage by pressing in
the yellow reset button at the bottom of the gage.
If you have a diesel engine, also see your Caterpillar


Operation & Maintenance Manual.

3-4
(Bi-Level Air Conditioning): This setting divides
airflow between the floor vents and instrument panel
vents. The air conditioning compressor will cycle
continuously in this setting as long as the outside air
temperature is warm enough to activate the compressor.
(Vent): This setting directs air through the
instrument panel vents.
(Floor): This setting directs air through the
floor vents.
(Defog): This setting divides airflow between the
floor vents and windshield vents.
(Defrost): This setting directs air through the
windshield vents. This setting is used to remove fog or
ice from the windshield.
Air Conditioning (If Equipped)
Before using the air conditioning, open the windows to
clear the vehicle of hot air. This reduces the time it takes
for your vehicle to cool down. Then keep your windows
closed for the air conditioner to work at its best.You can use maximum air conditioning with the
temperature knob in the blue area when it's really hot
outside and you need to cool the inside air quickly.
Maximum air conditioning lets in only a little air from
the outside.
If you first use maximum air conditioning, you can then
use regular air conditioning with the temperature knob
in the blue area, as soon as the vehicle has cooled down,
so outside air will be going through your vehicle.
While in maximum air conditioning, regular air
conditioning, bi
-level air conditioning, defog or defrost
mode, you may notice a slight increase or decrease in
engine speed, due to compressor operation. This is
normal because the system is designed to cycle the
compressor on and off to maintain the desired
temperature.
Heating
On cold days, use floor with the temperature knob in the
red area. Outside air will be brought in, heated and
distributed through the floor vents. The heater works
best if you keep your windows closed while using it.
If you use the optional engine coolant heater before
starting your engine, your heating system will produce
warmer air faster to heat the passenger compartment in
cold weather. See ªEngine Coolant Heaterº in the Index.

3-5 Defogging and Defrosting
Turn the mode knob to defrost to remove fog or ice from
the windshield quickly in extremely cold conditions.
The temperature knob should be in the red area with the
fan knob toward high.
To keep the windshield clear and send heated air
through the floor vents, turn the mode knob to defog.
The air conditioning compressor may operate in this
setting to dehumidify the air.
Rear Window Defogger (If Equipped)
If you see lines running across the rear windows, you
have a rear window defogger. The lines warm the glass.
For best results, clear the windows of as much snow or
ice as possible before using the rear window defogger.
To turn on the rear window
defogger, press this button
located near the fan control.
An indicator light in the
button will come on when
the rear window defogger
is working.The rear window defogger will only work when the
ignition is in RUN.
The rear window defogger will turn itself off after
several minutes. If you need additional warming time,
press the button again. Pressing the button when the
indicator light is illuminated will turn the defogger off.
NOTICE:
Don't use a razor blade or something else sharp
on the inside of the rear window. If you do, you
could cut or damage the warming grid, and the
repairs wouldn't be covered by your warranty.
Do not attach a temporary vehicle license, tape or decals
across the defogger grid on the rear windows. Use care
not to damage the wiring bands that connect the rear
window defogger grid when operating the rear
swing
-out windows (if equipped).

3-23 Care of Your Cassette Tape Player
A tape player that is not cleaned regularly can cause
reduced sound quality, ruined cassettes or a damaged
mechanism. Cassette tapes should be stored in their
cases away from contaminants, direct sunlight and
extreme heat. If they aren't, they may not operate
properly or may cause failure of the tape player.
Your tape player should be cleaned regularly after every
50 hours of use. Your radio may display CLN to indicate
that you have used your tape player for 50 hours without
resetting the tape clean timer. If this message appears on
the display, your cassette tape player needs to be
cleaned. It will still play tapes, but you should clean it as
soon as possible to prevent damage to your tapes and
player. If you notice a reduction in sound quality, try a
known good cassette to see if the tape or the tape player
is at fault. If this other cassette has no improvement in
sound quality, clean the tape player.
For best results, use a scrubbing action, non
-abrasive
cleaning cassette with pads which scrub the tape head
as the hubs of the cleaner cassette turn. The
recommended cleaning cassette is available through
your dealer (GM Part No. 12344789).The cut tape detection feature of your cassette tape
player may identify the cleaning cassette as a damaged
tape. To prevent the cleaning cassette from being
ejected, use the following steps:
1. Turn the ignition to RUN or ACCESSORY.
2. Turn the radio off.
3. Press and hold the TAPE button for two seconds
until the radio produces one beep. CAS will flash on
the display for five seconds.
4. Insert the scrubbing action cleaning cassette.
5. Eject the cleaning cassette after the manufacturer's
recommended cleaning time.
After the cleaning cassette is ejected, the cut tape
detection feature will be active again.
You may also choose a non
-scrubbing action, wet-type
cleaner which uses a cassette with a fabric belt to clean
the tape head. This type of cleaning cassette will not
eject on its own. A non
-scrubbing action cleaner may
not clean as thoroughly as the scrubbing type cleaner.
The use of a non
-scrubbing action, dry-type cleaning
cassette is not recommended.

3-24
After you clean the player, press and hold the eject
button for three seconds to reset the CLN indicator. The
radio will display
--- to show the indicator was reset.
Cassettes are subject to wear and the sound quality
may degrade over time. Always make sure the cassette
tape is in good condition before you have your tape
player serviced.
Care of Your Compact Discs
Handle discs carefully. Store them in their original cases
or other protective cases and away from direct sunlight
and dust. If the surface of a disc is soiled, dampen a
clean, soft cloth in a mild, neutral detergent solution and
clean it, wiping from the center to the edge.
Be sure never to touch the signal surface when handling
discs. Pick up discs by grasping the outer edges or the
edge of the hole and the outer edge.
Care of Your Compact Disc Player
The use of CD lens cleaner discs is not advised, due to
the risk of contaminating the lens of the CD optics with
lubricants internal to the CD mechanism.
Fixed Mast Antenna
The fixed mast antenna can withstand most vehicle
washes without being damaged. If the mast should ever
become slightly bent, you can straighten it out by hand.
If the mast is badly bent, as it might be by vandals, you
should replace it.
Check occasionally to be sure the mast is still tightened
to the fender. If tightening is required, tighten by hand,
then with a wrench one quarter turn.
Chime Level Adjustment
The radio is the vehicle chime producer. The chime is
produced from the driver's side front door speakers. To
change the volume level, press and hold pushbutton 6
with the ignition on and the radio power off. The chime
volume level will change from the normal level to loud,
and HI will be displayed on the radio. To change back
to the default or normal setting, press and hold
pushbutton 6 again. The chime level will change from
the loud level to normal, and LO will be displayed.
Each time the chime volume is changed, three chimes
will sound as an example of the new volume selected.
Removing the radio and not replacing it with a factory
radio or chime module will disable vehicle chimes.