2003 CADILLAC CTS turn signal

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Windows
2
-5 Keys
2
-7 Door Locks
2
-10 Remote Keyless Entry System
2
-16 Trunk Lid
2
-19 Theft
2
-21 Immobilizer
2
-24 New Vehicle ªBreak-Inº
2
-24 Ignition Positions
2
-27 Starting Your Engine
2
-28 Engine Coolant Heater (If Equipped)
2
-30 Automatic Transmission Operation
2
-37 Manual Transmission Operation
2
-38 Parking Brake
2
-40 Shifting Into PARK (P)
(Automatic Transmission Only)
2
-42 Shifting Out of PARK (P)
(Automatic Transmission Only)
2
-42 Parking Your Vehicle
(Manual Transmission Only)2
-43 Parking Over Things That Burn
2
-44 Engine Exhaust
2
-44 Running Your Engine While You're Parked
(Automatic Transmission)
2
-46 Turn Signal/Multifunction Lever
2
-56 Exterior Lamps
2
-59 Interior Lamps
2
-60 Mirrors
2
-70 OnStar
System (If Equipped)
2
-74 Sunroof (Option)
2
-75 HomeLink
Transmitter (If Equipped)
2
-80 The Instrument Panel -- Your
Information System
2
-85 Warning Lights, Gages and Indicators
2
-99 Driver Information Center (DIC)
2
-130 Vehicle Programming and
Personalization Features
2
-153 Navigation (Option)

2-46
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:

Turn and Lane
-Change Signals

Headlamps

Headlamp High/Low Beam
-Changer

Flash
-To-Pass Feature

Fog Lamps
For more information on the exterior lamps, see
ªExterior Lampsº later in this section.
Turn and Lane-Change Signals
To signal a turn, move the lever all the way up or down.
The lever returns automatically when the turn is
complete.
Arrows on the instrument
panel cluster flash in the
direction of the turn or
lane change.
Raise or lower the lever until the arrow starts to flash to
signal a lane change. Hold it there until the lane change
is complete. The lever returns to its original position
when it's released.
Arrows that flash rapidly when signaling for a turn or
lane change may be caused by a burned
-out signal bulb.
Other driver's won't see the signal.
Replace burned
-out bulbs to help avoid possible
accidents. Check the fuse and for burned
-out bulbs if the
arrow fails to work when signaling a turn. See ªFuses
and Circuit Breakersº in the Index for more information.

2-47
Turn Signal On Chime
If the turn signal is left on for approximately 1 mile
(1.61 km), a warning chime will sound and the
Turn Signal On message will appear on the Driver
Information Center (DIC) display. See ªTurn Signal
On Messageº later in this section for more information.
Headlamps
The exterior lamp control is located at the end of the
turn signal/multifunction lever.
: Turn the control with this symbol on it to operate
the exterior lamps.
The exterior lamp control has three positions:
: Turning the control to this position turns off all
lamps except the Daytime Running Lamps (DRL).
: Turning the control to this position turns on the
parking lamps together with the following:

Sidemarker Lamps

Taillamps

License Plate Lamps

Instrument Panel Lights
: Turning the control to this position turns on the
headlamps, together with the previously listed lamps
and lights.
AUTO (Automatic): Turning the control to this
position puts the headlamps in automatic mode. AUTO
mode will turn the exterior lamps on and off depending
upon how much light is available outside of the vehicle.
Wiper
-Activated Headlamps
This feature activates the headlamps and parking lamps
after the windshield wipers have been in use for
approximately six seconds. For this feature to work, the
exterior lamp control must be in AUTO.
When the exterior lamp control is off or in the parking
lamp position and the windshield wiper control is in any
position except off, the Headlamps Suggested message
will appear on the DIC display. See ªHeadlamps
Suggested Messageº later in this section for more
information.
When the ignition is turned to OFF, the wiper
-activated
headlamps will immediately turn off. They will also turn
off if the windshield wiper control is turned off.

2-48
Headlamp High/Low-Beam Changer
Push forward on the turn signal/multifunction lever to
change the headlamps from low to high beam. Pull the
lever back and then release it to change from high to
low beam.
This light on the instrument
panel cluster will be on,
indicating high
-beam usage.
Lamps On Reminder
A warning chime will sound if the exterior lamp control
is left on in either the headlamp or parking lamp
position and the driver's door is opened with the
ignition off.
Flash-To-Pass Feature
This feature allows you to use the high-beam headlamps
to signal the driver in front of you that you want to pass.
Pull and hold the turn signal/multifunction lever toward
you to use. When you do, the following will occur:

If the headlamps are either off, in low
-beam or in
Daytime Running Lamps (DRL) mode, the
high
-beam headlamps will turn on. They'll stay on
as long as you hold the lever there. Release the lever
to turn them off.

If the headlamps are in high
-beam mode, they will
switch to low beam. To return to high
-beam, push
the lever away from you.

2-49
Fog Lamps
Use the fog lamps for better vision in foggy or
misty conditions.
The fog lamp control is located on the turn
signal/multifunction lever to the left of the
steering column.The parking lamps must be on for the fog lamps
to work.
To turn the fog lamps on, turn the band on the lever up
to the fog lamp symbol and release it. The band will
return to its original position.
To turn the fog lamps off, turn the band up to the fog
lamp symbol and release it. The band will return to its
original position, and the fog lamps will turn off. If you
turn on the high
-beam headlamps, the fog lamps will
also turn off. They'll turn back on again when you
switch back to low
-beam headlamps.

2-56
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Applying the brake or shifting
into a lower gear will take you out of cruise control. If
you need to apply the brake or shift to a lower gear due
to the grade of the downhill slope, you may not want to
attempt to use your cruise control feature.Ending Cruise Control
To turn off the cruise control, step lightly on the brake
pedal, or press the cruise control on/off button on the
steering wheel.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.
Exterior Lamps
Headlamps
See ªTurn Signal/Multifunction Leverº listed previously
in this section for more information on the headlamps.

2-57
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset. Fully
functional daytime running lamps are required on all
vehicles first sold in Canada.
The DRL system will make the turn signal lamps come
on when the following conditions are met:

It is still daylight and the ignition is in ON
or START,

the exterior lamp control is in OFF or AUTO with
the headlamps off, and

an automatic transmission is not in PARK (P) or the
parking brake is not set on a manual transmission.
When DRL are on, only your turn signal lamps will be on.
No other exterior lamps will be on when the DRL are
being used. Your instrument panel won't be lit up either.
When the exterior lamp control is in AUTO and it's dark
enough outside, the DRL will turn off and the low
-beam
headlamps will turn on. When it's bright enough
outside, the low
-beam headlamps will go off, and the
DRL will turn back on.If it's dark enough outside and the exterior lamp control
is in OFF, a Headlamps Suggested message will appear
on the Driver's Information Center (DIC) display. This
message informs the driver that turning on the exterior
lamps is recommended even though the DRL are still
illuminated. Turning the exterior lamp control to AUTO
or to the low
-beam headlamp position will turn off the
DRL and cancel the Headlamps Suggested message.
If the parking lamps or the fog lamps were turned on
instead, the DRL will still turn off and the Headlamps
Suggested message will be displayed. You can turn it off
by pressing the OK button if you have the Navigation
audio system or the CLR button if you have the base
audio system.
To operate your vehicle with the DRL off, turn the
exterior lamp control to OFF. Then turn on the fog
lamps or parking lamps, and the DRL will turn off.
The Headlamps Suggested message will appear on the
DIC display. This will work regardless of gear position
and whether or not the parking brake is set.
As with any vehicle, you should turn on the regular
headlamp system when you need it.

2-77
2. Press the Learn or Smart button on the garage
door opener motor head unit. An indicator light will
begin to flash when the motor head unit enters the
training mode.
Following this step, you have 30 seconds to
start Step 3.
3. Return to HomeLink in your vehicle and firmly
press and release the programmed HomeLink button
three times.
The rolling
-code garage door opener should now
recognize HomeLink. You may either use HomeLink or
the hand
-held transmitter to open the garage door.
If after following these instructions, you still have
problems training the garage door opener, contact the
manufacturer of HomeLink at 1
-800-355-3515, or on
the internet at www.homelink.com.
Canadian Programming
Canadian Owners: During programming, the hand-held
transmitter may automatically stop transmitting after
two seconds. In this case, you should press and hold
the HomeLink button (see Steps 2 and 3 under
ªProgramming the HomeLink Transmitterº) while you
press and re
-press (cycle) your hand-held transmitter
every two seconds until HomeLink is trained.
Operating the HomeLink Transmitter
Press and hold the appropriate button on HomeLink for
at least half of a second. The indicator light will come
on while the signal is being transmitted.
Erasing Channels
To erase all three programmed channels, hold down the
two outside buttons until the indicator light begins to
flash (approximately 20 seconds). Release both buttons.