2003 BUICK RANDEZVOUS ECO mode

In many crashes severe enough to inflate an air bag,
windshields are broken by vehicle deformation.
Additional windshield breakage may also occur from the
right front passenger air bag.
•Air bags are designed to inflate only once. After an
air bag inflates, you’ll need some new parts for your
air bag system. If you don’t get them, the air bag
system won’t be there to help you in another crash. A
new system will include air bag modules and possibly
other parts. The service manual for your vehicle
covers the need to replace other parts.
•Your vehicle is equipped with an electronic frontal
sensor, which helps the sensing system distinguish
between a moderate frontal impact and a more
severe frontal impact. Your vehicle is also equipped
with a crash sensing and diagnostic module, which
records information about the frontal air bag system.
The module records information about the readiness
of the system, when the system commands air bag
inflation and driver’s safety belt usage at deployment.
The module also records speed, engine RPM, brake
and throttle data.
•Let only qualified technicians work on your air bag
systems. Improper service can mean that an air bag
system won’t work properly. See your dealer for
service.
Notice:If you damage the covering for the driver’s
or the right front passenger’s air bag, or the air
bag covering on the driver’s and right front
passenger’s seatback, the bag may not work
properly. You may have to replace the air bag
module in the steering wheel, both the air bag
module and the instrument panel for the right front
passenger’s air bag, or both the air bag module
and seatback for the driver’s and right front
passenger’s side impact air bag. Do not open or
break the air bag coverings.
1-75
2003 - Rendezvous OM

HomeLink®Transmitter
HomeLink, a combined universal transmitter and
receiver, provides a way to replace up to three
hand−held transmitters used to activate devices such as
gate operators, garage door openers, entry door
locks, security systems and home lighting. Additional
HomeLink information can be found on the internet
at www.homelink.com or by calling 1−800−355−3515.
If your vehicle is equipped with the HomeLink
®
transmitter, it complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of the
device.
Changes and modifications to this system by other than
an authorized service facility could void authorization
to use this equipment.
Programming the HomeLink®
Transmitter
Do not use the HomeLink®Transmitter with any garage
door opener that does not have the“stop and reverse”
feature. This includes any garage door opener model
manufactured before April 1, 1982.
Keep the original transmitter for use in other vehicles as
well as for future HomeLink
®programming. It is also
recommended that upon the sale of the vehicle,
the programmed HomeLink
®buttons should be erased
for security purposes. Refer to“Erasing HomeLink®
Buttons”or, for assistance, contact HomeLink®on the
internet at: www.homelink.com or by calling
1-800-355-3515.
Be sure that people and objects are clear of the garage
door or gate operator you are programming. When
programming a garage door, it is advised to park outside
of the garage.
2-34
2003 - Rendezvous OM

8. Return to the vehicle. Firmly press and hold the
programmed HomeLink®button for two seconds,
then release. Repeat the press/hold/release
sequence a second time, and depending on the
brand of the garage door opener (or other rolling
code device), repeat this sequence a third time
to complete the programming.
HomeLink
®should now activate your rolling code
equipped device.
To program the remaining two HomeLink
®buttons,
begin with Step 2 of“Programming HomeLink®.”Do not
repeat Step 1.
Gate Operator and Canadian
Programming
Canadian radio-frequency laws require transmitter
signals to“time out”or quit after several seconds of
transmission. This may not be long enough for
HomeLink
®to pick up the signal during programming.
Similarly, some U.S. gate operators are manufactured to
“time out”in the same manner.
If you live in Canada, or you are having difficulty
programming a gate operator by using the
“Programming HomeLink
®”procedures (regardless of
where you live), replace Step 3 under“Programming
HomeLink
®”with the following:Continue to press and hold the HomeLink
®button while
you press and release every two seconds (cycle)
your hand-held transmitter until the frequency signal has
been successfully accepted by HomeLink
®. The
indicator light willflash slowly atfirst and then rapidly.
Proceed with Step 4 under“Programming HomeLink
®”
to complete.
Using HomeLink®
Press and hold the appropriate HomeLink®button for at
least half of a second. The indicator light will come
on while the signal is being transmitted.
Erasing HomeLink®Buttons
To erase programming from the three buttons do the
following:
1. Press and hold down the two outside buttons until
the indicator light begins toflash, after 20 seconds.
2. Release both buttons. Do not hold for longer than
30 seconds.
HomeLink
®is now in the train (learning) mode and can
be programmed at any time beginning with Step 2
under“Programming HomeLink
®.”
Individual buttons can not be erased, but they can be
reprogrammed. See“Reprogramming a Single
HomeLink
®Button”next.
2-36
2003 - Rendezvous OM

Press the rear of the switch a second time and release
it to express-open the glass panel. The glass panel
and sunshade will fully open. When the glass panel is
express opening, pressing the switch in either direction
will stop it. If you press and hold the rear of the
switch, the express-open operation will be overridden.
To close the glass panel, press and hold the front of the
switch until the glass panel stops.
Vehicle Personalization
Some of your vehicle’s features can be reset or
customized according to your preference. The features
you can program depend on the options that came
with your vehicle.
If your vehicle has a DIC, seeDIC Vehicle
Personalization on page 3-57to customize your
features.
If you do not have the DIC, the following features
can be customized according to the options that your
vehicle has.
Entering Programming Mode
To program features, your vehicle must be in the
programming mode. Follow these steps:
1. Turn the ignition key to ON. The shift lever must be
in PARK (P).2. Press and hold the trip/reset button, located next to
the odometer for two seconds while the odometer is
in the odometer mode.
3. This message will appear in the message center,
located in the instrument panel cluster, as an
indication that your vehicle is ready to begin
programming.
If you have the remote keyless entry system, you
must press the LOCK button. This lets the
system know which transmitter is being
personalized, since each can be personalized
differently.
You can now program your choices.
To exit the programming mode, follow the steps listed
underExiting Programming Mode on page 2-51. United States
Canada
2-46
2003 - Rendezvous OM

Headlamp Exit Delay
This feature allows you to customize the headlamps and
parking lamps.
Programmable Modes
Mode 1:Off (The headlamps and parking lamps will
turn off at the same time that the ignition is turned
to OFF.)
Mode 2:15-Second Activation (The headlamps and
parking lamps will stay on for 15 seconds when
the ignition is turned to OFF.)
Mode 3:30-Second Activation (The headlamps and
parking lamps will stay on for 30 seconds when
the ignition is turned to OFF.)
Mode 4:60-Second Activation (The headlamps and
parking lamps will stay on for 60 seconds when
the ignition is turned to OFF.)
Your vehicle was originally programmed to Mode 3. The
mode may have been changed since then. To
determine the current mode, or to change the mode, do
the following:1. Follow the instructions forEntering Programming
Mode on page 2-46.
2. Turn the exterior lamp control from the off position
to the parking lamp position.
3. Count the number of chimes you hear. The number
of chimes indicates the vehicle’s current
programmed mode. If you do not wish to change
the current mode, you can either exit the
programming mode by following the instructions
later in this section or program the next feature
available on your vehicle.
4. Turn the exterior lamp control from the off position
to the parking lamp position to change the current
mode.
5. Turn the exterior lamp control from the off position
to the parking lamp position until you hear the
number of chimes corresponding to the mode
selection you want.
The mode you selected is now set. You can either exit
programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
2-47
2003 - Rendezvous OM

4. Press the front of the power door lock switch to
change the current mode.
5. Press the front of the power door lock switch until
you hear the number of chimes corresponding to
the mode selection you want.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
Delayed Locking
This feature allows you to delay the locking of your
doors.
Programmable Modes
Mode 1:Off (Doors will always lock immediately when
you lock the doors using the power door lock switch
or the remote keyless entry transmitter.)
Mode 2:Delayed Locking (If the power door lock
switch or the remote keyless entry transmitter is used to
lock the vehicle while any door is open, you will hear
three chimes. The doors will not lock. Five seconds after
the last door is closed, all doors will lock.)Your vehicle was originally programmed to Mode 2. The
mode may have been changed since then. To
determine the current mode, or to change the mode, do
the following:
1. Follow the instructions forEntering Programming
Mode on page 2-46.
2. Press the back of the power door lock switch.
3. Count the number of chimes you hear. The number
of chimes indicates the vehicle’s current
programmed mode. If you do not wish to change
the current mode, you can either exit the
programming mode by following the instructions
later in this section or program the next feature
available on your vehicle.
4. Press the back of the power door lock switch to
change the current mode.
5. Press the back of the power door lock switch until
you hear the number of chimes corresponding to
the mode selection you want.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
2-49
2003 - Rendezvous OM

Remote Driver Unlock Control
This feature allows you to customize the UNLOCK
button on the remote keyless entry transmitter.
Programmable Modes
Your vehicle can be programmed to one of the following
modes.
Mode 1:Remote All Doors Unlock (When you press
UNLOCK on your remote keyless entry transmitter,
all doors will unlock.)
Mode 2:Remote Driver’s Door Unlock Only (When you
press UNLOCK on your remote keyless entry
transmitter once, the driver’s door will unlock. When you
press UNLOCK on your remote keyless entry
transmitter again withinfive seconds, all doors will
unlock.)
Your vehicle was originally programmed to Mode 2. The
mode may have been changed since then. To
determine the current mode, or to change the mode, do
the following:
1. Follow the instructions forEntering Programming
Mode on page 2-46.
2. Press UNLOCK on the remote keyless entry
transmitter.3. Count the number of chimes you hear. The number
of chimes indicates the vehicle’s current
programmed mode. If you do not wish to change
the current mode, you can either exit the
programming mode by following the instructions
later in this section or program the next feature
available on your vehicle.
4. Press UNLOCK on the remote keyless entry
transmitter to change the current mode.
5. Press UNLOCK on the remote keyless entry
transmitter until you hear the number of chimes
corresponding to the mode selection you want.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
Remote Lock and Unlock
Confirmation
This feature allows you to customize the feedback
received when locking or unlocking your vehicle with the
remote keyless entry transmitter.
Programmable Modes
Mode 1:Both Features Off (Remote lock and unlock
confirmation are disabled.)
2-50
2003 - Rendezvous OM

Mode 2:Exterior Lamps Flash Only
•When you use the remote keyless entry transmitter
to lock or unlock your vehicle, your headlamps and
parking lamps willflash briefly to let you know
the command has been received.
Mode 3:Exterior Lamps Flash and Horn Sound
•When you use the remote keyless entry transmitter
to lock your vehicle, your headlamps and parking
lamps willflash briefly on each press and your horn
will sound briefly on the second or any other
press to let you know the command has been
received.
•When you use the remote keyless entry transmitter
to unlock your vehicle, your headlamps and parking
lamps willflash briefly to let you know the
command has been received.
Your vehicle was originally programmed to Mode 3. The
mode may have been changed since then. To
determine the current mode, or to change the mode, do
the following:
1. Follow the instructions forEntering Programming
Mode on page 2-46.
2. Press the LOCK button on the remote keyless entry
transmitter.
3. Count the number of chimes you hear. The number
of chimes indicates the vehicle’s current
programmed mode. If you do not wish to changethe current mode, you can either exit the
programming mode by following the instructions
later in this section or program the next feature
available on your vehicle.
4. Press LOCK on the remote keyless entry transmitter
to change the current mode until you hear the
number of chimes corresponding to the mode
selection you want.
The mode you selected is now set. You can now exit
the programming mode by following the instructions next
in this section.Exiting Programming Mode
To exit programming mode, do one of the following:
•Press the odometer button, while in odometer mode
for two seconds, or
•turn the ignition key out of ON, or
•do not program any commands for one minute
while in programming mode, or
•shift out of PARK (P). SeeShifting Out of Park (P)
on page 2-28.
The programming mode message will turn off to let you
know that you are no longer in the programming mode.
2-51
2003 - Rendezvous OM