2002 YAMAHA YFM660R lock

8-81 1. Upper wheel hub nut 2. Lower wheel hub nut
1.Écrou supérieur de moyeu de roue
2.Écrou inférieur de moyeu de roue
1. Tuerca superior del cubo de la rueda
2. Tuerca inferior del cubo de la rueda
1. Locknut (× 2) 2. Adjusting bolt (× 2)
3. Alignment marks (× 2)
1. Contre-écrou (× 2) 2. Boulon de réglage (× 2)
3. Repères d’alignement (× 2)
1. Contratuerca (× 2) 2. Perno de ajuste (× 2)
3. Marcas de alineación (× 2)
EBU01026
Drive chain slack adjustment
1. Loosen the rear wheel hub upper and lower
nuts.
2. Loosen the adjusting bolt locknuts on each
side of the swingarm. To tighten the drive
chain, turn the adjusting bolts in direction
a.
To loosen the drive chain, turn the adjusting
bolts in direction
b and push the wheels for-
ward. Turn each adjusting bolt exactly the
same amount to maintain correct axle align-
ment.
There are alignment marks on each side of
the swingarm and on the hub. Use them to
check for proper wheel axle alignment.
3. After adjusting, tighten the adjusting bolt lock-
nuts and the wheel hub nuts to the specified
torques.
Tightening torques:
Locknut:
16 Nm (1.6 m·kgf)
Upper wheel hub nut:
90 Nm (9.0 m·kgf)
Lower wheel hub nut:
90 Nm (9.0 m·kgf)
U5LP61.book Page 81 Monday, August 27, 2001 3:49 PM

8-113 1. Headlight bulb holder
1. Fixation d’ampoule de phare
1. Portabombillas del faro
1. Headlight bulb 2. Headlight bulb holder
1. Ampoule de phare 2. Fixation d’ampoule
1. Bonbilla del faro 2. Portabombillas del faro
7. Push the headlight bulb holder inward, turn it
counterclockwise and remove the defective
bulb.
WARNING
_ A headlight bulb is hot when it is on and imme-
diately after it is turned off. Wait for the bulb to
cool down before touching or removing it. You
can be burned, or a fire could start if the bulb
touches something flammable. _8. Put a new headlight bulb into position and se-
cure it in place with the bulb holder.
9. Install the headlight bulb holder cover.CAUTION:_ Make sure the headlight bulb holder cover is
securely fitted over the bulb holder and seated
against the reflector. _10. Align the projections with the holders, install
the headlight unit into the case, and install the
screw.
11. Install the headlight cover in the original posi-
tion, and then install the screw.
U5LP61.book Page 113 Monday, August 27, 2001 3:49 PM

8-117 1. Lens 2. Screw (× 2)
1. Lentille 2. Vis (× 2)
1. Lente 2. Tornillo (× 2)
1. Bulb
1. Ampoule
1. Bombilla
EBU01021
Tail/brake light bulb replacement
1. Remove the screws and the lens.
2. Remove the defective bulb by pushing it in-
ward and turning it counterclockwise.
3. Install a new bulb by pushing it inward and
turning it clockwise.
4. Install the lens and tighten the screws.CAUTION:_ Do not overtighten the screws as the lens may
break. _
U5LP61.book Page 117 Monday, August 27, 2001 3:49 PM

9-1
EBU00418
CLEANING AND STORAGE
A. CLEANING
Frequent, thorough cleaning of your machine will
not only enhance its appearance but will improve
its general performance and extend the useful life
of many components.
1. Before cleaning the machine:
a. Block off the end of the exhaust pipe to pre-
vent water entry. A plastic bag and strong
rubber band may be used.
b. Make sure the spark plug and all filler caps
are properly installed.
2. If the engine case is excessively greasy, ap-
ply degreaser with a paint brush. Do not ap-
ply degreaser to the chain, sprockets or
wheel axles.
3. Rinse the dirt and degreaser off with a garden
hose. Use only enough pressure to do the
job.
U5LP61.book Page 1 Monday, August 27, 2001 3:49 PM

9-9
5. Block up the frame to raise all wheels off the
ground.
6. Tie a plastic bag over the exhaust pipe outlet
to prevent moisture from entering.
7. If storing in a humid or salt-air atmosphere,
coat all exposed metal surfaces with a light
film of oil. Do not apply oil to any rubber parts
or the seat cover.
8. Remove the battery and charge it. Store it in
a dry place and recharge it once a month. Do
not store the battery in an excessively warm
or cold place (less than 0°C or more than
30°C).NOTE:Make any necessary repairs before storing the
machine.
U5LP61.book Page 9 Monday, August 27, 2001 3:49 PM